Memphis Shades 2320-0070 User manual

2320-0070 SPORTSHIELD DETACHABLE MOUNTING KIT HARLEY WIDE, BLACK
MOUNTING INSTRUCTIONS
Figure 3Figure 1
Space Approx.
2" apart.
WARNING:
"Mounting clamps
backwards will cause
damage to your tank."
Figure 2
MEB8920 1-1-11
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
No additional tools required for this kit.
1. Cover gas tank and front fender with a towel to avoid
damage during installation.
2. Install the windshield mounting plates onto the windshield,
using the bolts that are pre-assembled on the mounting plates.
The Santoprene grommets should be inserted through the
holes in the windshield so that the flat round part of the grom-
met lies flat on each side of the plastic. Tabs point in towards
the headlight. (see figure 1 )
3. Loosely install the four Fork Clamps on the forks, approxi-
mately 2" apart. (see figure 2)
4. Start with Fork Clamp Bushing adjusted to rear of slot (see
figure 4) Then adjust as needed and check for clearance. (See
warning above.)
5. Slip the windshield mounting plates and windshield onto
the fork clamps, (see figure 3 and 5) and secure the left and
right side locking mechanism
6. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after in-
stalling the windshield! (see figure 5)
Read and follow these directions carefully.
During installation, make certain that when turning the
forks, there can be no interference with wiring or cables
AND, that the windshield can not hit the gas tank,
through the windshield's full range of adjustment.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
Start with Fork Clamp Bushing ad-
justed to rear of slot. Then adjust as
needed and check for clearance. (See
above "Read and Follow Directions
Warning.")
Fig. 4
Bushings
Throttle side,
front of bike
INCORRECT
CORRECT

CORRECT
Fully engaged
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
123
Figure 5
4
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
R322C/T
LATCH
ASSEMBLY
1. M532
2. M520
3. M1136
4. M1135
2
3
1
BUSHING
ASSEMBLY
4
2320-0070 SPORTSHIELD KIT
2320-0070 SPORTSHIELD DETACHABLE MOUNTING KIT HARLEY WIDE
MOUNTING INSTRUCTIONS
PART #
M8920
M543
DESCRIPTION
MOUNTING INSTRUCTIONS
SANTOPRENE GROMMET
M504EB
M505EB
SOCKET SHOULDER WASHER
BUTTON NUT
4
4
4
M302
1/4"-20 x 1/2” SS SOCKET HEAD CAP SCREW 4
M1136EB
RIGHT SPORTSHIELD MOUNTING PLATE 1
M1135EB
LEFT SPORTSHIELD MOUNTING PLATE
QTY.
1
1
M520
INNER ADJUSTABLE FORK CLAMP 4
M532
OUTER DETACHABLE ADJUSTABLE FORK CLAMP 4
PART #
M369
DESCRIPTION
STAINLESS STEEL WASHER
M306 1/4"-20 x 5/8" SS SOCKET HEAD CAP SCREW 4
4
M313 3/16" ALLEN WRENCH COVER 1
QTY.
M310 3/16" SHORT ARM ALLEN WRENCH 1
R329 SLOT NUT 4
R323
BUSHING ASSEMBLY (2 PART) 4
M318EB
1" SOCKET SHOULDER WASHER 4
R324
#207 EPDM O-RING 4
BUSHING ASSEMBLY
A C
C
D
E
F
A. R329
B. M369
C. R323
D. R324
E. R318
F. M306
B
R322C/T LATCH ASSEMBLY 2
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us at
[email protected]