Two Brothers Racing 005-630406V User manual

Parts List
IMPORTANT - PLEASE READ CAREFULLY
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
We recommend that this performance part be installed by a qualied
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions rst before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Installation Instructions
1. Make sure the bike is completely cool before starting
the installation. Make sure the bike is secure on a
center stand or ideally a service lift.
2. Remove right side panel.
3. Remove upper mufer mounting bolts.
4. Remove S-bend mufer joint clamp.
5. Remove mufer assembly.
6. Assemble the V.A.L.E.™unit by slipping the S-bend
tube through the X-lite™ring. Use the 4 (four) 6 x
14mm bolts and split lock washers to loosely attach
the X-Lite™ ring to mufer inlet.
7. Make sure that the supplied barrel clamp is at the
S-bend joint to the head pipe, slip S-bend tube of
V.A.L.E.™muffler assembly into head pipe. Use
supplied 8 x 45mm socket head with washer through
muffler mount and spacer (tapered side towards
mufer) then loosely attach to motorcycle using the
OEM nut.
Qty. Description Part Number
1 M-7 Mufer Canister 005-63-206M/207M
1 Stainless Steel S-Bend Tube 005-6301S
1 HARDWARE KIT 005-63-3
1 X-Ring Kit 005-7-2-3KIT
1 Barrel Clamp 005-27-59MSH
1 8mm Flat Washer 005-WF8
1 20mm Spacer 005-S-22-20
1 8x45mm Socket Head Cap Screw 005-SH845
1 Spark Arrestor (aluminum canister only) 005-106S
8. Making sure that the V.A.L.E.™assembly is oriented
correctly, securely tighten upper mufer mounting bolt.
9. Securely tighten the 4 (four) 6 x 14mm hex head bolts
of the V.A.L.E.™assembly.
10. Securely tighten the lower mufer barrel clamp.
11. Re-install right side panel.
12. Double check to make sure that all hardware is fully
tightened.
13. Before you run the bike, clean off all ngerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run
the bike and enjoy. It is normal for some white smoke to
appear the rst time you start the bike. This is packing/
manufacturing oil from inside the pipe burning off.
Check for gaps or leaks. If you nd a leak, a little high
temperature silicon sealant should x it. After 50 to
100 miles, recheck all fasteners for tightness.
Mufer Inlet
X-Lite™ Ring
S-Bend Tube
V.A.L.E.™ Assembly Detail
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a
soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright nish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the berglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon ber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the berglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon ber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon ber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
1997-2013 Kawasaki
KLR650
Slip-on V.A.L.E.™ Exhaust System with M-7 Canister
Part # 005-630406V / 005-63407V

Parts List
Qty. Description Part Number
1 M-7 Mufer Canister 005-63-206M/207M
1 Stainless Steel S-Bend Tube 005-6301S
1 HARDWARE KIT 005-63-3
1 X-Ring Kit 005-7-2-3KIT
1 Barrel Clamp 005-27-59MSH
1 8mm Flat Washer 005-WF8
1 20mm Spacer 005-S-22-20
1 8x45mm Socket Head Cap Screw 005-SH845
1 Spark Arrestor (aluminum canister only) 005-106S
1997-2013 Kawasaki
KLR650
Slip-on V.A.L.E.™ Exhaust System with M-7 Canister
Part # 005-630406V / 005-63407V