Memphis Shades 2320-0026 User manual

Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
Additional tools required, that are not included in this kit.
7/16" or 11mm wrench.
1. Cover gas tank and front fender with towels to avoid
damage during installation.
4. Install the two mounting plates onto the windshield, using
the bolts that are pre-assembled on the mounting plates. The
Santoprene Grommets should be inserted through the holes in
the windshield so that the flat round part of the Grommet lies
flat on each side of the windshield. Tabs point in towards the
headlight. (See Figure 1)
5. Slip the windshield mounting plates and windshield onto
the upper and lower bushing assemblies, (see figure 2 and 3)
and secure the left and right side locking mechanism.
6. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make sure
the Locking Mechanism is Fully Engaged after installing
the windshield! (see figure 3)
MOUNTING INSTRUCTIONS
2320-0026 Detachable Plate Only Kit
Sportshield for H-D Covered with Light Bar
MEM8823 05-30-08
Read and follow these directions carefully.
During installation, make sure that the windshield and hard-
ware do not interfere with any cables or wiring when the forks
are turned all the way in either direction. Also make sure,
through the full range of adjustment, that the windshield and
hardware do not hit the tank.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
Figure 1 Figure 2

2320-0026 Detachable Plate Only Kit
Sportshield for H-D Covered with Light Bar
MOUNTING INSTRUCTIONS
2320-0026
PLATE ONLY
KIT
MEM8823 05-30-08
CORRECT
Fully engaged
Locking mechanism
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
Figure 3
Loosen Allen Bolts A & B to adjust angle, then re-tighten Allen
Bolts.
R322c/tS
SLANT
LATCH
ASSEMBLY
1. M1149
2. M1150
1 2
4
QTY .
4
4
2
2
8
BUTTON NUTM505
DESCRIPTIONPART #PART #
M1150
M8823
DESCRIPTION
RIGHT SPORTSHIELD MOUNTING PLATE
MOUNTING INSTRUCTIONS/PARTS LIST
QTY.
1
1
M1149 LEFT SPORTSHIELD MOUNTING PLATE 1
M578 SELF ADHESIVE PLASTIC WASHER 4
4M301 1/4" - 20 X 3/8" SOCKET HEAD CAP SCREW
M302
1/4”-20 x 1/2” SS SOCKET HEAD CAP SCREW
M504 SOCKET SHOULDER WASHER
R322c/tS SLANT LATCH ASSEMBLY
R326 LATCH SPRING
R334 LATCH SCREW
R329 SLOT NUT 4
M501 3/4” BEVELED SOCKET WASHER 4
SANTOPRENE GROMMETM543 4
1234
A
B
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us by email:
[email protected]