Mercia Garden Products 03DTSHCR0909GD4TW-V2 User manual
2mm Drill bit
x2
ANY QUESTIONS?
Scan the QR code to
contact us via our customer
portal.
PLEASE SCAN HERE:
8
Some steps within this set of instructions come with an added video guide for your
convenience. These can be accessed via the QR code and used to aid you in constructing that
step. See below for how to use.
You can also nd all the videos on our youtube channel:
https://www.youtube.com/@merciagardenproducts8716/videos
ACCESSING VIDEO GUIDES...
1.Find the QR code within the instruction step...
2. Open camera app...
3. Scan QR code...
4. Watch the video...
On your personal smart device (phone, tablet etc), open your camera app or QR code scanner
app.
To scan the QR code, hold the camera over the QR code so that it can be seen on the screen.
Once the QR code has been registered, follow the prompts on your device to open the video.
(This will vary depending on your device.)
Please note: Ensure to use the back camera of your smart device as this will scan the QR code more
accurately.
The video guide will now be displayed on your smart device.
Parts Needed- No. QTY 1
No. QTY 1
No. QTY 1
Step.....
Within the instruction step, there will be an icon in the top right that has a QR code in. This
is where the video can be accessed from.
Please note: not every step has a video guide.
Disclaimer: The garden building constructed in the video guides may be
constructed dierently to your building. Please ensure to read your instructions
carefully to avoid error.
ACCESSING VIDEO GUIDES...
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Width = 3164mm
Depth = 2918mm
Height = 2146mm
Base Dimensions:
Width = 3033mm
Depth = 2799mm
23
24
13
15
1
Door Panel
QTY 1
AI-03S11SHDD1627X2092-V1
2
Window Panel
QTY 2
AI-03S11SH2TFWC1600X2092-V1
Roof Support Bar 44x58x2740mm QTY 1
F4458-2740mm
Fascia 12x95x1445mm QTY 4
S1295-1445mm
Fascia 12x95x1689mm QTY 2
S1295-1689mm
Fascia 12x95x1725mm QTY 1
S1295-1725mm
Cover Trim 12x40x2105mm QTY 4
S1240-2105mm
Cover Trim 12x40x2008mm QTY 2
S1240-2008mm
Door Strip 12x40x1261mm QTY1
S1240-1261mm
Rear Roof Frame 28x28x2888mm QTY 1
FS2828-2888mm
Front Roof Frame 28x28x1678mm QTY 1
FS2828-1678mm
Panel Joint Frame 28x28x1920mm QTY 1
FS2828-1920mm
25
20
14
21
22
17
19
Rear Cover Trim 12x60x1915mm QTY 2
S1260-1915mm
Locating Block 28x28x239mm QTY 2
FS2828-239mm
3
Large Right Panel
QTY 1
AI-03S11SHPGR1389X2094-V1
4
Small Right Panel
QTY 1
AI-03S11SHPGR1417X2017-V1
5
Large Left Panel
QTY 1
AI-03S11SHPGL1389X2094-V1
6
Small Left Panel
QTY 1
AI-03S11SHPGL1417X2017-V1
8
Angled Floor
1503x2800mm
QTY 1
AI-R11MBAF1503X2800-V1
7
Floor
648x2800mm
QTY 2
AI-R11MBF648X2800-V1
9
Roof
843x2889mm
QTY 2
AI-S11MBPR843X2889-V1
10
Angled Roof
1204x2889mm
QTY 1
AI-S11MBANGRR1204X2889-V1
11
Master Door QTY 1
AI-STDFGMD603X1715-V1
12
Secondary Door QTY 1
AI-STDFGSD603X1715-V1
16
Door Strip 12x40x1740mm QTY 2
S1240-1740mm
18
Contents:
Green Label Blue Label
Green Label
Green Label
Blue Label
Blue Label
34
29
32
31
35
33
Butt Hinge QTY 6
PI-07-0066
Press Lock QTY 1
PI-07-0162
Handle QTY 2
PI-07-0081
L-Bracket QTY 2
PI-07-0012
Turn Button QTY 2
PI-07-0034
Barrel Bolt QTY 2
PI-07-0114
30
Felt QTY 3
PI-01-0013
Rain Guard - 28x44x1400mm QTY 3
RG2844-1400mm
27
28
Rear Panel Framing 28x28x2780mm QTY 1
FS2828-2780mm
26
Front Panel Framing 28x28x1600mm QTY 1
FS2828-1600mm
30mm Screw x 71
50mm Screw x 122
60mm Screw x 6
40mm Screw x 33
Felt Tacks x100
25mm Screw x 40
Nail Bag
There may be extra screws present in the nail bag
10mm Screw x 12
35mm Bolt x 4
Pre Assembly
Before assembling remove the transportation blocks from the bottom
of each panel.
Take care removing the blocks as to not damage the panels. Tap with a
at headed screwdriver and hammer.
Dispose of the blocks once removed.
PLEASE SCAN HERE:
Pre drill
hole
25mm
screw
1
11
12
32
Step 1
Parts needed - No.1 QTY 1
No.11 QTY 1
No.12 QTY 1
No.32 QTY 6
Lay the Door Panel (No.1) on a at surface and place
the doors (No.11 and No.12) within the Door Panel
aperture. Position the doors so that they are equally
spaced within the opening and interlock as shown.
Fix the Butt Hinges (No.32) onto the door and Door
Panel as shown. Ensure that the screws go through
the cladding and into the framing behind.
**PLEASE NOTE** Before tting the hinges, ensure
the inner door framing is the correct way round as
shown in the illustration.
36x25mm Screws
IMPORTANT: Pre-drill before xing screws.
11
12
50mm
screw
Pre drill
hole 6
35
4
Step 2
Parts needed - No.3 QTY 1
No.4 QTY 1
No.5 QTY 1
No.6 QTY 1
Fix Large Right Panel (No.3) to Small
Right Panel (No.4) and Fix Large Left
Panel (No.5) to Small Left Panel
(No.6) using 4 50mm screws per join.
8x50mm Screws
IMPORTANT: Pre-drill before xing screws.
IMPORTANT: Pre-drill before xing screws.
50mm
screw
Pre drill
hole
8
77
Step 3
Parts needed - No.7 QTY 2
No.8 QTY 1
Place oors (No.7 & No.8) on a rm and
level base, ensure base has suitable
drainage free from areas where standing
water can collect. (See front page on
base requirements).
Fix the three oor panels together as
shown using 50mm screws at an angle
and alternate the positions.
12x50mm Screws
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
60mm
screw
Step 4
Parts needed - No. 1 QTY 1
No. 2 QTY 2
Place the Door Panel (No. 1) and the
Window Panels (No. 2) onto the oor.
Fix the corners with 3x60mm screws as
shown in the illustration.
Do not secure the building to the oor
until the roof is tted.
6x60mm Screws
2
1
aa
a
a
a
a
2
a
IMPORTANT: Pre-drill before xing screws.
Step 5
Parts needed - No.5 QTY 1
No.6 QTY 1
No.18 QTY 1
Place the two already assembled Left
Panels (No.5 and No.6) against the
oor and the Window Panel.
Fix the corners with 3x50mm screws
as shown in the illustration.
Attach the Panel Joint Frame (No.18)
into place with 3x50mm screws.
Do not secure the building to the
oor until the roof is tted.
6x50mm Screws
50mm
screw
Pre drill
hole
a
a
a
18
6
5
18
a
IMPORTANT: Pre-drill before xing screws.
Step 6
Parts needed - No. 3 QTY 1
No. 4 QTY 1
Using the same method outlined
in Step 5 place the two already
assembled Right Panels (No.3 &
No.4) against the oor and other
Panels securing using 6x50mm
screws.
From the inside x the corners with
3x50mm screws as shown in the
illustration.
Do not secure the building to the
oor until the roof is tted.
6x50mm Screws
50mm
screw
Pre drill
hole
4
3
a
a
a
a
a
a
a
IMPORTANT: Pre-drill before xing screws.
50mm
screw
Pre drill
hole
Step 7
Parts needed - No. 26 QTY 1
No. 27 QTY 1
Place the Rear Panel Framing (No.26)
on top of the Right Panels. Fix in place
using 4x50mm screws.
Place the Front Panel Framing (No.27)
on top of the Window Panel. Fix in
place using 3x50mm screws.
7x50mm Screws
26
27
IMPORTANT: Pre-drill before xing screws.
Step 8
Parts needed - No.19 QTY 1
No.31 QTY 2
Fix an L bracket (No. 31) ush to
each end of the roof support (No.
19) using 2x30mm screws for each
bracket. Position the roof support
(No. 19) in-between the left
gables and the window panel
opposite.
Line the roof support up so it sits
centrally at the panel join and x in
place with 2x30mm screws. Make
sure the roof support sits centrally
to the window upright shown in
the illustration. Fix in place with
2x30mm screws.
8x30mm Screws
Pre drill
hole
30mm
screw
19
31
31
¡
IMPORTANT: Pre-drill before xing screws.
Step 9
Parts needed - No.9 QTY 2
No.10 QTY 1
Layout the Roof Panels (No.9 & No.10)
on a at level surface and position
them as shown in the diagram. Secure
the panels together using 50mm
screws and alternate the positions.
12x50mm Screws
9
9
10
50mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
24
23
40mm
screw
Pre drill
hole
Step 10
Parts needed - No.13 QTY 2
No.23 QTY 1
No.24 QTY 1
Attach the front (No.24) roof
framing to the roof as shown in the
illustration using 3x30mm screws.
Attach the rear (No.23) roof
framing to the roof as shown in the
illustration using 5x30mm screws.
*Ensure to x the framing the
opposite direction to the roof
bearers.
Fix the Locating Blocks (No.13) to
the opposing sides to the roof
framing (these blocks are to help
square the roof when tted).
12x40mm Screws
** If the Shed add on pack has been purchased, do
not t No.23 ,the rear roof framing, until instructed
to do so in the Shed add on Pack instructions**
13
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
50mm
screw
Step 11
Parts needed - No.9 QTY 2
No.10 QTY 1
Place all Roof sections (No.9 & No.10)
on top of the building, ensure the roof
framing slots over each side equally all
the way around.
Fix the Roof Panels into position using
50mm screws, ensuring there is no
more than 300mm between each
screw.
Make sure that the screws line up with
the vertical framing inside the building
and along the length of the internal
roof support bar.
33x50mm Screws
10
9
9
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
30mm
screw
Step 12
Further secure the Roof Panels in place
using 30mm screws. Ensure to screw
through the cladding with no more
than 300mm between each screw.
28x30mm Screws
Step 13
Secure the building to the oor. Fix the
panels onto the oor using 50mm
screws in alignment with the oor joists
*Ensure to screw through the framing
into the oor bearers.
29x50mm Screws
50mm
screw
Pre drill
hole
b
b
b
b
b
b
b
b
b
bb
b
IMPORTANT: Pre-drill before xing screws.
30mm
screw
Pre drill
hole
14
15 15
IMPORTANT: Pre-drill before xing screws.
Step 14
Parts needed - No.14 QTY 1
- No.15 QTY 2
Fit the Door Strip (No.14 & No.15)
to the framing of the door panel,
secure using 3x30mm screws per
strip
9x30mm Screws
*Internal View*
IMPORTANT: Pre-drill before xing screws.
35mm
bolt
35
Step 15
Parts needed - No. 29 QTY 2
- No. 35 QTY 2
Fix the door handles (No.35) to the
outside of the master and secondary
door using the 35mm bolts provided.
Fix the Turn buttons (No.29) at the top
and bottom of the secondary door
using 2x30mm screws.
2x30mm Screws
4x35mm Bolts
35
Pre drill
hole
10mm
screw
29
29
29
35
*External View*
Secondary door Master door
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
10mm
screw
25mm
screw
34
*Internal View*
Secondary Door
Master Door
b
Pre drill
holes
33
Attach the press lock (No.34) to the
master door with 4x25mm screws,
aligning the barrel with the key hole.
*Ensure the key turns and locks
properly before xing to the door.
Place the Tower Bolts (No.33) roughly
into position at the top/bottom of the
secondary door. With a pencil mark
around the bolt.
After marking the bolt onto the panel,
drill a hole for the barrel bolt to locate
into.
Following the hole being drilled, place
the tower bolts into position and secure
using 4x10mm screws per bolt.
8x10mm Screws
4x25mm Screws
c
Step 16
Parts needed - No. 33 QTY 2
No. 34 QTY 1
c
a
b
a
Step 17
Parts needed - No. 30 QTY 1
Cut four strips from the rolls of felt
(No.30):
2 x 430cm (L) X 100cm (W)
1 x 350cm (L) X 100cm (W)
1 x 150cm (L) X 100cm (W)
Place the felt on top of the roof and
align as shown in diagram ensuring
each strip overlaps the next by
20cm. Ensure all strips over hang
roof by 5cm.
Ensure strip 1 is the rst piece
placed down then lay sheet 2, 3 and
then 4 on top.
Cut the sides as shown in diagram
at the dotted lines, use fascia width
as guide for overhang.
Fix each sheet using felt tacks along
where sheet overlap.
Use felt tacks at 100mm intervals.
200 x Felt Tacks
HANDLE
WITH CARE
12
3
4
100cm
20cm
20cm
20cm
5cm
5cm
5cm
430cm
350cm
150cm
1
2
3
4
5cm
30
30
30
30
Please note: It is advisable to place a board across the length of
the roof to kneel on whilst felting.
Felt
tacks
**If Shed add on Pack has been purchased,
please move onto the Add on Pack Instructions**
100mm
IMPORTANT: Pre-drill before xing screws.
30mm
screw
Pre drill
hole
16
16
16
16
Step 18
Parts needed - No. 16 QTY 4
Fit the Cover Trims (No.16) to the front
of the building onto the joins of the
panels, secure using 3x30mm screws
per cover trim.
12x30mm Screws
Step 19
Parts needed - No. 17 QTY 2
- No. 25 QTY 2
Fit the Cover Trims (No.17) to the
back of the building onto the joins
of the panels, secure using 3x30mm
screws per cover trim.
Fix the rear cover trims (No.25) to
the back of the building, aligning
with the edge of the panel.
12x30mm Screws
30mm
screw
Pre drill
hole
25 25
17
17
IMPORTANT: Pre-drill before xing screws.
IMPORTANT: Pre-drill before xing screws.
Step 20
Parts needed - No. 20 QTY 4
No. 21 QTY 2
No. 22 QTY 1
Fit the fascias (No.20, 21 & 22) to
the building over the felt and
secure in place with 3x40mm
screws per cover trim.
Make sure the fascias at the back
of the building t lower than the
roof height to allow water to run
o.
21x40mm Screws
40mm
screw
Pre drill
hole
20
20
20
20
21
22 21
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
50mm
screw
Step 21
Parts Needed - No.28 QTY 3
Fix the rain guards (No.28) above the
door and both sets of windows, securing
in place using 3x50mm screws per guard,
ensuring to screw through the framing.
9x50mm Screws
28
28
28
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
AFTER TREATMENT:
score around protective
cover on glazing and
carefuly peel
covering back
Want to share your experience with us?
Leave us a review on Feefo, TrustPilot or Google.
Your reviews help other people nd and trust our
business, as well as helping to play an important role
in our growth and improvement!
¡
¡
¢
ANY QUESTIONS?
Scan the QR code to
contact us via our customer
portal.
PLEASE SCAN HERE:
¢
£
¡
£
1
2
3
4
5
6
7
8
9
¤
¥
¤
2
1
¦
3
4
¥
£
¦
¡
¥
12
£
¦
¡
Table of contents
Other Mercia Garden Products Garden House manuals
Mercia Garden Products
Mercia Garden Products 01DTSHPN0806SDFW-V1 User manual
Mercia Garden Products
Mercia Garden Products 01DTPRMSHAX1010DDOP-V1 Instruction manual
Mercia Garden Products
Mercia Garden Products 03TGCORSE0408-V1 Instruction manual
Mercia Garden Products
Mercia Garden Products 0619LOG018-V4 Instruction manual
Mercia Garden Products
Mercia Garden Products SI-002-001-0022 User manual
Mercia Garden Products
Mercia Garden Products 01DTOVRA0806SDFW-V1 Instruction manual
Mercia Garden Products
Mercia Garden Products 01OVLPA0304SDNW-V1 User manual
Mercia Garden Products
Mercia Garden Products 0634LOG209-V4 Instruction manual
Mercia Garden Products
Mercia Garden Products 0628RASH0302FBSDNW-V1 User manual
Mercia Garden Products
Mercia Garden Products 01OVLPA0806SDFW-V2 User manual
Mercia Garden Products
Mercia Garden Products 01DTOVRA0604SDFW-V1 User manual
Mercia Garden Products
Mercia Garden Products 02DTSHOPN0305-V1-PEFC Instruction manual
Mercia Garden Products
Mercia Garden Products 0644LOG133-V4 Instruction manual
Mercia Garden Products
Mercia Garden Products 01OVLPA0705SDFW-V1 Instruction manual
Mercia Garden Products
Mercia Garden Products 01GRODB1008-V3 Instruction manual
Mercia Garden Products
Mercia Garden Products 01PTOSBA0705SDFW-V1 Instruction manual
Mercia Garden Products
Mercia Garden Products 03TGCOR0707-V5 Instruction manual
Mercia Garden Products
Mercia Garden Products 01GRO1006DD-V2 Instruction manual
Mercia Garden Products
Mercia Garden Products 01DTOVRA0806SDFW-V2 User manual
Mercia Garden Products
Mercia Garden Products 0628AXNE0503HGDD2MW-V1 User manual
Mercia Garden Products
Mercia Garden Products 03DTSHPN0409DSHPB-V1 User manual
Mercia Garden Products
Mercia Garden Products 0628AXNE0403HGDD1SW-V1 User manual
Mercia Garden Products
Mercia Garden Products 01OVLPA1010DDFW-V1 User manual
Mercia Garden Products
Mercia Garden Products 01PTOSBA0306DDNW-V1 Instruction manual
Popular Garden House manuals by other brands
Palmako
Palmako FRB28-3226 installation manual
Lemeks
Lemeks Palmako FR28-3232-9 Assembly, installation and maintenance manual
Lemeks
Lemeks Palmako FR44-5540-9 Assembly, installation and maintenance manual
OLT
OLT Santa Rosa SR812-FJ-Cedar Assembly manual
Luoman
Luoman Lillevilla 264-1 Assembly and Maintenance
Palmako
Palmako Susanna FR44-5340 installation manual
Palmako
Palmako Roger FR44-3857-2 installation manual
Lemeks
Lemeks ELF16-3535 installation manual
Lemeks
Lemeks Palmako FR44-5123 Assembly, installation and maintenance manual
Lemeks
Lemeks Palmako FR28-3020-2 Assembly, installation and maintenance manual
Solid
Solid S8969 Assembly instructions
Werth-Holz
Werth-Holz 46210 Assembly
Lemeks
Lemeks Palmako 109503 Assembly, installation and maintenance manual
STILLA
STILLA Oxford 6x9 S3021 Assembly instructions
Panda
Panda XPANDAOFFICE Assembly instructions
Décor et Jardin
Décor et Jardin 67457S900 Assembly Notice
Outdoor living today
Outdoor living today SS84S-METAL-FJ Assembly manual
Luoman
Luoman LILLEVILLA Tyrni Assembly and Maintenance