Mercia Garden Products 10DTSHAX0806-V1 User manual







 

 
















  



2mm Drill bit
x2 





















































¡







 


































¢













¡





 
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Width = 2056mm
Depth = 2458mm
Height = 2054mm
Base Dimensions:
Width = 1888mm
Depth = 2386mm
Large Mesh Panel QTY 2
AI-10S11MESDP1193X1560-V1
Gable Top QTY 1
AI-S11SHASDGT1808X402-V1
Finial QTY 2
Shed Diamond
L Bracket QTY 4
PI-07-0012
Turn Button QTY 6
PI-07-0034
Pad Bolt QTY 1
PI-07-0035
Ply Triangle QTY 2
Roof Panel QTY 4
AI-S11MBAR1205X1075-V1
6” T-Hinge QTY 7
PI-07-0082
Door Panel QTY 1
AI-10S11SHAGSD1808X1959-V1
Side Panel QTY 2
AI-S11SHPP1193X1571-V1
Plain Panel QTY 1
AI-10S11SHAGP1808X1972-V1
Mesh Door QTY 1
AI-10S11MESLFD538X1639-V1
Small Mesh Panel QTY 2
AI-10S11MESSP630X1560-V1
Door A QTY 1
AI-S11FMBMZBD542X965-V1
Door B QTY 1
AI-S11FMBMZBD542X695-V1
Fascias - 12x60x1100mm QTY 4
S1260-1100mm
25
9 10 11
21
27
23
24
22
1
5678
234
Ridge Bar - 27x44x1153mm QTY 1
F2744-1153mm
12
Bearer - 27x44x1119mm QTY 2
F2744-1119mm
13
Bearer - 27x44x1860mm QTY 3
F2744-1860mm
14
29
Support Framing - 28x28x949mm QTY 2
FS2828-949mm
19
20 28
Ridge Bar - 27x44x1137mm QTY 1
F2744-1137mm
15
16
Cover Trim - 12x40x1582mm QTY 4
S1240-1582mm
17
Bearer - 27x44x1135mm QTY 2
F2744-1135mm
18
8x6 Building Contents:
10DTSHAX0806-V1
Felt
Capping Felt
Floor QTY 3
AI-S21MBF599X1122-V1
Door Strip - 12x27x1615mm QTY 1
S1227-1615mm
U Shaped Channel QTY 2
PI-07-0013
26

£
 
Roof Panel QTY 2
AI-S11MBAR630X1075-V1
Bearer - 27x44x630mm QTY 3
F2744-630mm
U Shaped Channel QTY 3
PI-07-0013
40mm screws x 62
50mm screws x 76
70mm screws x 32
30mm screws x 141
31
32
30
36
Truss support - 27x44x958mm QTY 2
F2744-G-978mm (958mm nished length, 1 x angled cut)
33
Truss Block - 27x44x140mm QTY 2
F2744-G-160mm (140mm nished length, 1 x angled cut)
34
Truss Brace - 27x44x450mm QTY 1
F2744-G-450mm (450mm nished length, 2 x angled cuts)
35
Nail Bags
There may be extra screws present in the nail bag
30mm Black Screw x 6
Felt Tacks x 150
2x6 Pack B Contents:
10DTSHAX0206PB-V1
Small Mesh Panel QTY 2
AI-10S11MESSP630X1560-V1
*If you have purchased a 2ft extension pack B, please follow steps for
‘Extension Pack B’ where relevant.*
Overall Dimensions:
Width = 2056mm
Depth = 2458mm
Height = 2054mm
Base Dimensions:
Width = 1888mm
Depth = 2386mm
10x6 Building.
10DTSHAX0806-V1 + 10DTSHAX0206PB-V1
Pre Assembly
Before assembling, remove the transportation
blocks from the bottom of each panel.
Take care removing the blocks as to not damage
the panels. Tap with a at headed screwdriver
and hammer.
Dispose of the blocks once removed.


 
Step 1
Parts Needed - No. 13 QTY 2
No. 14 QTY 2
Position the bearers (No. 13 & 14) on your
base as shown, ensure bearers No.13 sits
inside bearers No.14.
Fix the framing together with 2x70mm
screws per corner.
Ensure to construct your bearers on a rm
and level base, that has suitable drainage
free from areas where standing water can
collect. (See front page on base require-
ments).
8x70mm screws.
Pre drill
hole
70mm
screw
13
14
IMPORTANT: Pre-drill before xing screws.
13
14
IMPORTANT: Pre-drill before xing screws.
2
3
Step 2
Parts Needed - No. 3 QTY 1
No. 2 QTY 1
Place the Side Panel (No. 2) and the Plain
Panel (No. 3) onto the bearers and x
together at the corner with 3x50mm
screws.
**Do NOT x to the bearers until the Roof
is secured**
3x50mm screws.
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
2
Step 3
Parts Needed - No. 2 QTY 1
Place the second Side Panel (No. 2) onto
the bearers and x to the Plain Gable with
3x50mm screws.
**Do NOT x to the bearers until the
Roof is secured**
3x50mm screws.
Pre drill
hole
50mm
screw
a
a
a
a
1
Pre drill
hole
50mm
screw
Step 4
Parts Needed - No. 1 QTY 1
Place the Door Panel (No. 1) onto the
bearers. Fix the Door Panel (No. 1) to the
side panels with 3x50mm screws per side.
**Do NOT x to the bearers until the
Roof is secured**
6x50mm screws.
IMPORTANT: Pre-drill before xing screws.
a
a
a
a
a
a
a


 
IMPORTANT: Pre-drill before xing screws.
15
15
14
Step 5
Parts Needed - No. 14 QTY 1
No. 15 QTY 2
Place the remaining bearers (No.14 & 15)
into position as shown and secure to each
with 2x70mm screws per corner.
*The Run bearers do not x to the Kennel
area*
4x70mm screws.
Pre drill
hole
70mm
screw
Step 5a - EXTENSION PACK B
Parts Needed - No. 14 QTY 1
No. 15 QTY 2
No. 33 QTY 2
Place the remaining bearers (No.14 & 15
& 33) into position as shown and secure to
each with 2x70mm screws per corner.
Secure the adjacent bearers together
using 2x70mm screws per join. Screw at
an angle through to the next bearer.
*The Run bearers do not x to the Kennel
area*
8x70mm screws.
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
70mm
screw
15
15
33
33
14
Step 5b - EXTENSION PACK B
Parts Needed - No. 30 QTY 2
Locate the Small Mesh Panels (No. 30) on
top of the front bearers.
Fix to the adjacent panel using 3x50mm
screws per panel.
**Do NOT x to the bearers until the
Roof is secured**
6x50mm screws.
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
50mm
screw
30
30
a
a
a
a
a
a
a

¡
 
4
Step 6
Parts Needed - No. 4 QTY 2
Locate both Large Mesh Panel (No. 4) onto
the front bearers as shown.
Fix the panels into the adjacent panels with
3x50mm screws per panel.
**Do NOT x to the bearers until the Roof
is secured**
6x50mm screws.
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
4
aa
a
a
a
a
a
10X6 EXTENSION PACK B
4
4
a
a
a
a
a
a
IMPORTANT: Pre-drill before xing screws.
6
6
Step 7
Parts Needed - No. 6 QTY 2
Locate both Small Mesh Panels (No. 6)
onto the front bearers as shown.
Fix to the Large Mesh Panels with 3x50mm
screws per panel, making sure you screw
from the inside.
**Do NOT x to the bearers until the
Roof is secured**
6x50mm screws.
Pre drill
hole
50mm
screw
a
a
a
a
a
a
a
10X6 EXTENSION PACK B
6
6
a
a
a
a
a
a


 
Step 8
Parts Needed - No. 10 QTY 1
Locate the Gable Top (No. 10) on top
of the two Small Mesh Panels (No. 6),
as shown.
Secure in place using 4x50mm
screws per panel.
4x50mm screws
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
10X6 EXTENSION PACK B
10
10
Step 9
Parts Needed - No. 24 QTY 2
Locate the Ply Triangles (No. 24)
to the top and bottom of the
door way, as shown.
Fix in place using 2x40mm
screws per triangle.
4x40mm screws
Pre drill
hole
40mm
screw
24
IMPORTANT: Pre-drill before xing screws.
10X6 EXTENSION PACK B
24
24

¤
 
17
16
Step 10
Parts Needed - No. 16 QTY 1
No. 17 QTY 1
No. 22 QTY 4
Inside the Kennel part of the building,
locate the Ridge Bar (No.17) in between
the Plain Panel and the Door Panel, in line
with the central framing of the gables.
Fix the Ridge Bar (No.17) in place using
one L-bracket (No.22) per end. Secure
with 4x30mm screws per bracket.
In the Run part of the building, locate the
Ridge Bar (No.16) in between the Door
Panel and the Gable Top, in line with the
central framing of the gables.
Fix the Ridge Bar (No.16) in place using
one L-bracket (No.22) per end. Secure
with 4x30mm screws per bracket.
16x30mm screws
IMPORTANT: Pre-drill before xing screws.
22
22
22
22
Pre drill
hole
30mm
screw
22
22
22
Step 10a - EXTENSION PACK B
Parts Needed - No. 16 QTY 1
No. 17 QTY 1
No. 22 QTY 4
No. 32 QTY 1
No. 33 QTY 4
Inside the Kennel part of the building,
locate the Ridge Bar (No.17) in between
the Plain Panel and the Door Panel, in line
with the central framing of the gables.
Fix the Ridge Bar (No.17) in place using
one L-bracket (No.22) per end. Secure
with 4x30mm screws per bracket.
Secure the Ridge Bars (No.16 & 33)
together using the U-channel (No.32)
with 6x30mm screws. Ensure the framing
is ush and level.
In the Run part of the building, locate the
assembled Ridge Bar (No.16 & 33) in
between the Door Panel and the Gable
Top, in line with the central framing of the
gables.
Fix the assembled Ridge Bar in place using
one L-bracket (No.22) per end. Secure
with 4x30mm screws per bracket.
22x30mm screws
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
30mm
screw
17
16
22
22
22
22
33
32
32
22
22
22


 
Step 11
Parts Needed - No. 19 QTY 2
Locate the Support Framing (No.19) ush
with the front of the Gable Top (No.10)
Secure in place with 3x50mm screws per
frame, screwing through the framing into
the Gable behind.
6x50mm screws
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
50mm
screw
19
19
10X6 EXTENSION PACK B
19
19
Step 12
Parts Needed - No. 11 QTY 4
No. 26 QTY 2
Pre drill
hole
30mm
screw
IMPORTANT: Pre-drill before xing screws.
aPlace the Roof Panels (No.11) on top of
the building, making sure the framing
in the roof panels sits rmly within the
Gables and on top of the ridge bar.
**Make sure that you have got the
Roof Panels the correct was around,
with the recess at the top of the apex,
as shown in the diagram.
Ensure the edges of the Roof Panels are
ush with the outer cladding of the
Plain Gable and the Gable Top.
Once the Roofs have been located on
the building, Locate a U-channel
(No.26) across the join between the
two adjacent Roof Panels framing, as
shown.
Ensure the U-channel is spaced over
both Roofs framing equally, and secure
in place using 6x30mm screws per
channel.
Repeat this for both Roofs.
From the top, x directly through the
roof panels (No.11) and into the Ridge
Bars below using 12x50mm screws.
It is essential that the Ridge Bars and
Roof Panel framing pull together when
xed. You may require another person
pushing the Ridge Bars up from below
to achieve this.
**Note: Be cautious of the roof panels
before they are secured to the
building. They may need added
support until xed.
12x30mm screws.
12x50mm screws.
c
b
50mm
screw
11
11
11
11
26
b
c
a
26
11 11
b