Mercia Garden Products 03BRN0705-V3 Instruction manual

N/A
Overlap
Cladding
Shiplap
Cladding
Solid Sheet
Roof
T&G Roof
Solid Sheet
Floor
T&G Floor
Fixed
Windows
Opening
Windows
No
Windows
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be erected by two
adults
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are coated with a water based high quality colorant; this only
helps to protect the product during transit and for up to 3 months against
mould. To validate your guarantee and ensure longevity of the product, it is
ESSENTIAL the building is treated with a wood preserver within the rst three
months of assembly and thereafter in accordance with the manufactures
recommendations. Care must be taken to ensure the product is placed on a
suitable base
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products
independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer
to diagrams for the base dimensions, The base should be slightly smaller than
the external measurement of the building, i.e. The cladding should overlap the
base, creating a run o for water. It is also recommended that the oor be at
least 25mm above the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Please retain product label and instructions for future reference
P 1
General Instructions
Refer to the instructions pages for your specic product code
The images used throughout the instruction manual are generic and for
illustration purposes only; they may vary dependant on your actual product. It is
strongly advised they are read and understood before attempting installation.
03BRN0705-V3
7x5 Bournmouth Summerhouse
03BRN0707-V3
7x7 Bournmouth Summerhouse with Veranda
03BRN0807-V3
8x7 Bournmouth Summerhouse with Veranda

P 2
03BRN0705-V3
Overall Dimensions:
Length = 1744mm
Width = 2281mm
Height = 2191mm
Base Dimensions:
Length = 1448mm
Width = 2082mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Fixing Kit
Contents
2
1
3
4
5
67
9
11
12
13 14 15 16 17
10
Eaves Frame - 28x28x1720mm Qty 2
Angled Fascia Block - 44x44x340mm Qty 1
Ridge Bar - 27x44x1457mm Qty 1
Finial Qty 2
Fascia - 12x60x1240mm Qty 4
Fascia Block - 27x44x140mm Qty 2
Chrome
handle
Qty 2
Press lock
Barrel bolt
Qty 2
Corner
Bracing
Qty 2
Turn
button
Qty 2
Butt hinge
Qty 6
Felt
20
18
19
8
Door Gable Plain Gable Plain Side
Qty 2
Floor Roof Sheet
Qty 2
Master
Door
Slave
Door
Nail Bag
50mm Screw x26
40mm Screw x22
16mm Black Screw x6
30mm Screw x50
35mm Bolt x4
10mm Screw x12
Felt Tacks x75
25mm Screw x18

P 3
Please retain product label and instructions for future reference
Step 1
Remove transportation
blocks from the bottom
of each panel before
beginning assembly. Each
Panel should have two.
Step 2
Lay the door gable on a flat
surface and place both doors
into the door aperture.
Position the doors so that they
are equally spaced within the
opening.
Fix the butt hinge to the doors
using 25mm screws. Ensuring
the doors are positioned
equally fix the hinges to the
door panel using 30mm
screws.
Pre drill
hole
18x25mm Screws
15
18x30mm Screws
30mm
screw
25mm
screw
16 7
Step 3
Place the floor on a firm and
level base, ensure the base has
suitable drainage free from
areas where standing water
can collect. (See front page on
base requirements).
4
Fix the corner with 3x
50mm screw as shown in
the diagram.
Step 4
3x50mm screws
Pre drill
hole
50mm
screw
23

P 4
Please retain product label and instructions for future reference
Fix the corners with 3x
50mm screw as shown in
the diagram.
Step 5
9x50mm screws
Pre drill
hole
50mm
screw
1
3
Fix a corner brace to both
ends of the ridge bar using
30mm screws. Fix the Ridge
bar between both gables
ensuring the top edges of
the ridge bar finish flush
with the top of the gales. Fix
in place using 30mm screws
Step 6
9
20
8x30mm screws
30mm
screw
Pre drill
hole
Fix a roof eave to the edge
of the roof sheet using
30mm screws. Do this for
both roof eaves and roof
sheets.
Step 7
8x30mm screws
30mm
screw
Pre drill
hole
5
8
Fix the roof sheets on either
side of the building as
shown in the diagram.
Fix the panels into position
using 30mm screws from
the top of the panel straight
into the framing and ridge
bar.
Step 8
16x30mm screws
30mm
screw
Pre drill
hole
5
5

P 5
Please retain product label and instructions for future reference
14x50mm screws
Fix the panels onto the
floor using 50mm screws in
alignment with the floor
joists.
Step 9
50mm
screw
Pre drill
hole
6x40mm screws
Fix the angled fascia block
to the apex of the two roof
sheets, ensure the block sits
flush with the edge of the
roof sheets. Secure with
2x40mm screws.
Place a fascia block in the
middle of each roof sheet
flush with the edge, fix in
place with 2x40mm screw
Step 10
40mm
screw
Pre drill
hole
11 12
12
HANDLE
WITH CARE
12
3
4
Cut felt into 3 equal sheets
measuring 1820mm and lay onto
roof as shown in diagram ensuring
there is a 50mm overhang around
the sides.
Fix using felt tacks at 100mm
intervals
Step 11
75x felt tacks
14

P 6
Please retain product label and instructions for future reference
Fit the fascias to the front and back
of the roof sheets ensuring to trap
the felt between the fascia and the
roof sheet. Use 40mm screws to x
the fascias in place.
Fix the nial where the fascias come
together at the apex of the building
at the front and back using 40mm
screws.
Step 12
16x40mm screws
40mm
screw
Pre drill
hole
10
13
10
10
10
13
Pre drill holes then fix the Chrome
Handle using 35mm bolt as shown
in diagram.
Step 13
2x35mm Bolt
35mm
bolt
Pre drill
hole
17
Step 14
16
18
Fix the press lock to the door
using 4x16mm black screws
ensuring the key hole lines up
with the hole in the door.
Fit the barrel bolts to top and
bottom of the door as shown in
the diagram. Use 4x10mm
screws per barrel bolt.
Ensure doors open and close
freely.
16mm
screw
Pre drill
hole
4x16mm Black Screws
12x10mm Screws
10mm
screw
Pre drill
hole
2x16mm Black screws
These turn buttons help to keep your doors
straight during high levels and low levels of
moisture content in the air.
Slave Door
Locking Door
19
Step 15
Attach a turn button to the top and
bottom of the slave door using 16mm
black screws.
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
AFTER TREATMENT:
score around protective
cover on glazing and
carefuly peel
covering back
16mm
screw
Pre drill
hole