Mercia Garden Products Wessex 03WES0808-V3 Instruction manual

P 1
03WES0808-V3
8x8 Wessex Summerhouse
2mm Drill bit
x2 Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All buildings should be
erected by two adults
For ease of assembly, you
MUSTpilot drill all screw
holes and ensure all screw
heads are countersunk.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatanundilutedcontains:boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
Please retain product label and instructions for future reference
General Instructions
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, Wood saw, Step ladder, Hammer and a
Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for up to 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufacturers recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for your specic product code
For ease of assembly, you
will need a tape measure to
check dimensions of
components.
Pressure Treated Timber
Pressure treating is a chemical process which helps to protect wood against adverse weather which could
lead to rot or insect damage.
The most common chemicals used to pressure treat wood are Alkaline Copper Quaternary(ACQ),
Copper Azole (CA), and Micronized Copper Quaternary(MCQ).
Safety:Always wear gloves, eye protection and a dust mask when handling wood. Due to chemicals in
pressure treated wood, never burn its sawdust or scraps; instead dispose in a landll.

50mm Screw x 29
40mm Screw x14
Felt Tacks x100
20mm Screw x12
30mm Screw x70
30mm Black Screw x48
Door Gable
AI-03WESDG2354X2213-V3
Plain Gable
AI-03WESG2354X2213-V3
Window Panel
AI-03WESWP1757X1698-V3 x2
Plain Panel
AI-03WESPP1757X1698-V3 x2
Floor
AI-03WESF2350X1753-V3
Window
AI-03FW540X1132-V1
Veranda
AI-03WESV2387X628-V3
Roof
AI-03WESR2409X1345-V3
x2
Rail
AI-03WESRAIL-V3
x2
Master Door
AI-03MDFG1720X475-V1
Slave Door
AI-03FG1720X475-V1
Fascia 1385mm S1365-1385mm angled x4
Veranda Upright 1699mm F2744-1720mm angled x2
Cover Strips 1694mm S1240-1694mm x4
Window Cross A 500mm WC1627-500mm x6
Window Cross B 1094mm WC1627-1094mm x3
Press Lock
PI-07-0018
2x Ring Pull
PI-07-0032
6x Hinge
PI-07-0004
2x Turn Button
PI-07-0032
20mm Black Screw x10
10mm Screw x6
P 2
03WES0808-V3
Overall Dimensions:
Width = 2494mm
Depth = 2457mm
Height = 2293mm
Base Dimensions:
Width = 2379mm
Depth = 2395mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
2
134
567
20
8
12
910 11
14
16
17
18 19
13
21
Gable Trims 624mm S1228-624mm x8
15
Nail Bag
22
PI-07-0011
4x Window Blocks
23
2x Shed Finial
SHED DIAMOND FINIAL

2
4
3
5
P 3
Please retain product label and instructions for future reference
Step 1
Place the Floor (No. 5)onto a at,
level base, ensuring the base has
suitable drainage, free from areas
where standing water can collect.
Step 2
Place the Plain Gable (No. 2)and Plain
Panel (No. 4)onto the Floor. Secure the
Panels together with 3x50mm screws as
shown.
**Do not x to the Floor until the Roof is
itted.
3x50mm screws.
Pre drill
hole
50mm
screw
Step 3
Fix the Window panel (No. 3)into position
with 3x50mm screws.
**Do not x to the Floor until the Roof is
itted.
3x50mm screws.
Pre drill
hole
50mm
screw
Pre Assembly
Remove the transportation blocks from
the bottom and top of each panel
before beginning assembly

P 4
Please retain product label and instructions for future reference
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Step 4
Fix the Door Gable (No. 1)into position
with 3x50mm screws.
**Do not x to the Floor until the Roof is
itted.
3x50mm screws.
Pre drill
hole
50mm
screw
Step 5
Place the Veranda (No. 6)at the front of
the building.
**Do not x to the Floor until the Roof is
tted.
Step 6
Place a Roof panel (No. 7)onto the build-
ing, making sure the Roof rests into the
gaps in the framing in the front and back
panel.
Fix as shown with 6x30mm screws.
**Do not x to the Floor until the Roof is
itted.
6x30mm screws.
Pre drill
hole
30mm
screw
Step 7
Fix the Veranda Upright (No. 13)to the
building as shown with 2x50mm screws.
**Do not x to the Floor until the Roof is
itted.
2x50mm screws.
Pre drill
hole
50mm
screw
1
6
7
13

P 5
Please retain product label and instructions for future reference
Step 8
Place the Right Roof (No. 7)onto the
building, making sure the Roof rests into
the gaps in the framing on the front and
back panel.
Fix as shown with 6x30mm screws.
Fix the Veranda Upright (No. 13)to the
building as shown with 2x50mm screws.
**Do not x to the Floor until the Roof is
itted.
6x30mm screws.
2x50mm screws.
Pre drill
hole
30mm
screw
Step 9
Fix the Gable Trims (No. 15)to the build-
ing with 2x30mm screws per Trim.
Fix the Cover Strips (No. 14)to the corners
of the building with 3x30mm screws per
trim. The Trims attached to the front of
the building will need to be cut to t at
angle.
Repeat for the rear of the building.
**Do not x to the Floor until the Roof is
itted.
28x30mm screws.
Pre drill
hole
30mm
screw
Step 10
Fix the building to the Floor with
4x50mm screws per panel.
16x50mm screws.
Pre drill
hole
50mm
screw
Step 11
Fix the Rails (No. 8)to the building as
shown with;
- 3x40mm screws through into the
veranda per rail.
- 4x40mm screws through into the
building and into the veranda upright per
rail.
14x40mm screws.
Pre drill
hole
40mm
screw
15
15
7
15
15
8
8
13
50mm
screw
*Cut down
trims to t
14 14

P 6
Please retain product label and instructions for future reference
Please retain product label and instructions for future reference
HANDLE
WITH CARE
12
3
4
Step 12
Cut the Felt into 3 equal lengths and lay
onto the roof as shown in the diagram.
Making sure there is 50mm of overhang.
Fix to the buildings using evenly spaced
felt tacks.
100xFelt tacks.
Step 13
To x the Window (No. 11) into the panels
that accomodate a window. First x the
Window Block to the Window as shown
with 1x30mm screw.
Place the Window into the window hole
and x by screwing though the Window
Block (No. 22) with 2x30mm screws as
shown.
4 window blocks per window.
*Screw into the Window rst.
**Door Gable windows come secured
within the panel.
12x30mm screws.
Pre drill
hole
30mm
screw
Step 14
Fix 3 Hinges (No. 20)to each Door
(No. 9 & No. 10)securing with 4x30mm
black screws per hinge. Position as
shown.
Fix each Door to the building with
4x30mm black screws per hinge.
48x30mm black screws.
Pre drill
hole
30mm
screw
Felt tacks

P 7
Please retain product label and instructions for future reference
Step 15
Fix the Fasicas (No. 12)to the building
with 3x30mm screws per Fascia.
12x30mm screws.
Pre drill
hole
30mm
screw
Step 16
Fix the Finials (No. 23)to the building
with 2x30mm screws per Finial.
4x30mm screws.
Pre drill
hole
30mm
screw
Step 17
Fix a Ring Pull (No. 19)to each door with
4x20mm black screws per Finial.
8x20mm black screws.
Pre drill
hole
20mm
screw
12
12
12
12
23
23
19 19
18
Step 18
Fix the Press lock (No. 18)to the
back of the Master door with
4x30mm screws. Making sure to
align the key holes.
4x30mm screws.
Pre drill
hole
20mm
screw

P8
Please retain product label and instructions for future reference
Step 20
Fix the Window Crosses (No. 16 & No. 17)
into the windows securing with 6x20mm
screws.
Further secure the crosses with 10mm at
each meeting point.
12x20mm screws.
6x10mm screws.
Pre drill
hole
10mm
screw
Step 19
Fix the Turn Buttons (No. 21)to the top of
each door with 1x20mm black screw per
Button.
2x20mm black screws.
Pre drill
hole
20mm
screw
21
17
16
16
20mm
screw
AFTER TREATMENT:
score around protective
cover on glazing and
carefuly peel
covering back
It is ESSENTIAL that you apply wood treat-
ment immediately after the building has
been assembled.