Mercia Garden Products 01OSBP0602SD Instruction manual

01OSBP0602SD
N/A
Overlap
Cladding
Shiplap
Cladding
Solid Sheet
Roof
T&G Roof
Solid Sheet
Floor
T&G Floor
Fixed
Windows
Opening
Windows
No
Windows
6X2’6”Wall Pent
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be erected by two
adults
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to
protect the product during transit and for upto 3 months against mould. To
validate your guarantee and ensure longevity of the product, it is ESSENTIAL the
building is treated with a wood preserver within the rst three months of
assembly and thereafter in accordance with the manufactures recommenda-
tions. Care must be taken to ensure the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Whilst all products manufactured are made to the
highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot
accept responsibility for your safety whilst erecting or
using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
**Protim Fentex E5**
Biocidal Product Regulation (EU 528/2012) Article 58 Information
Protim Fentex E2 preserved wood is a “treated article” which incorporates biocidal products.
Wood correctly preserved with Protim Fentex E2 is protected against mould in storage.
Contains: IPBC (3-iodo-2-propynyl-N-butyl carbamate) and propiconazole.
Wear gloves when handling freshly treated wood.
Avoid breathing dust when cutting treated or untreated wood.
Dispose of o-cuts responsibly – do not burn.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer
to diagrams for the base dimensions, The base should be slightly smaller than
the external measurement of the building, i.e. The cladding should overlap the
base, creating a run o for water. It is also recommended that the oor be at
least 25mm above the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Please retain product label and instructions for future reference
P 1
General Instructions
Refer to the instructions pages for you specic product code

1 2 3 4 5 6 7 8
9
Pre drill
hole
50mm
screw
4
7
2
P 2
01OSBP0602SD
Overall Dimensions:
Length = 1786mm
Width = 797mm
Height = 1960mm
Base Dimensions:
Length = 1786mm
Width = 797mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Front Panel Plain Gable Door Gable Rear Panel Double Door
QTY 2
Side Door Floor Roof Sheet
QTY 2
Gable Tops
L & R
Door Block - 140mm QTY 2
Eaves Frame - 1786mm
Cover Trim - 1759mm QTY 2
Rear Fascia - 1810mm
Side Fascia - 830mm QTY 2
30mm Screw x110
50mm Screw x30
40mm Screw x15
10mm Felt Tacks x80
Turn Button QTY 2 Pad Bolt QTY 2
T-Hinge QTY 6
Pre Assembly
Remove transportation blocks
from each panel before
beginning assembly.
Step 1
Place the oor on a rm and level
base, ensure the base has suitable
drainage and is free from areas
where standing water can collect.
Nail Bag
Step 2
Fix the corners with
3x50mm screws.
Do NOT secure to the
oor until the roof
is tted.
3x50mm Screws
10
11
12
13
14
15 16
16

Pre drill
hole
50mm
screw
3
1
Pre drill
hole
30mm
screw
Pre drill
hole
50mm
screw
P 3
Please retain product label and instructions for future reference
Step 3
Fix the corners with
3x50mm screws.
Do NOT secure to the
oor until the roof
is tted.
9x50mm Screws
9
9
Step 4
Place the Gable Tops onto the
building, ensuring the framing
is level and ush with the
gable. Secure using 4x30mm
Screws as shown in the
illustration.
4x30mm Screws
8
11
Step 5
Fix the eaves frame to the edge
of the roof sheet using 4x30mm
screws.
Place the roof into position
ensuring the eaves frame sits
against the front panel.
Screw into position using
10x30mm screws as shown
in the illustration.
*Fix eaves frame to roof
sheet rst.
14x30mm Screws
Step 6
Secure the building to the
oor using 12x50mm
screws.
Ensure to align the
screws with the oor
bearers.
12x50mm Screws
Pre drill
hole
30mm
screw

Step 7
Lay the sheet of felt onto the roof
ensuring there is approximately
50mm of overhang around the
sides.
Fix using 80x felt tacks at 100mm
intervals.
80x Felt Tacks
Felt
tacks
P 4
Please retain product label and instructions for future reference
Step 8
Fix the T-hinges to the doors with
30mm screws ensuring to locate
the screws into the door framing.
Position each door into the door
gap leaving 2mm gap between the
doors and the building. Fix in place
using 30mm screws.
Attach the pad bolts to the
horizontal brace of either
double door and the bolt
retainer on the opposite door.
Secure the door block & turn
buttons to the top & bottom
framing of the door with the
retainer attached, using 30mm
screws
58x30mm Screws
Pre drill
hole
30mm
screw
16
17
15 10
Step 9
Attach the cover trims to
the side of the building
using 3x30mm screws
per trim.
6x30mm Screws
Pre drill
hole
30mm
screw
12 12
14
14
13
Step 10
Fit the fascia boards to the
rear and sides of the building
using 3x40mm screws per
fascia.
Attach the remaing pad bolt
to the side door following
the same method outlined
in Step 8.
10x30mm Screws
9x40mm Screws
Pre drill
hole
30mm
screw
40mm
screw
17

It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
P 5
Please retain product label and instructions for future reference