Merrithew STOTT PILATES STABILITY CHAIR User manual

E
B
CA
9
16
17
H
156
2
4
78
3
SPLIT-PEDAL
CHAIR BODY
WITH HANDLES
F
G
Ahorizontal frame complete with pedal
Bwooden sides (R/L)
Cchair handle receptacles (R/L)
Dvertical frame
Emiddle support
Fchair handles (R/L)
Gchair handles chrome extension (R/L)
Hchair top
GLOSSARY OF PARTS
1, 2, 3, 91⁄4" x 2" carriage bolts with nuts
41⁄4" x 1-1⁄2" hex bolts with washers
5, 61⁄4" x 1-1⁄2" hex bolts with washers and nuts
7, 81⁄4" x 2-1⁄4" hex bolts with washers and nuts (models with handles)
7*, 8* 1⁄4" x 2" carriage bolts with nuts (models without handles)
10, 11, 12, 13 1⁄4" x 2" hex bolts with washers
14, 15 3⁄8" x 3⁄4" hex bolts with washers
16 5/16" pop-up pins
17 1/4" x 1" round stud knobs
18 heavy chair springs (red)
19 light chair springs (blue)
20 chair lock
21 star knobs
◗1/2"x 7/16" open end wrench (supplied)
◗1/2"x 9/16" open end wrench (supplied)
TOOLS REQUIRED
5
6
1
2
3
9,
7*
8*
*indicates models without handles
4
7
8
10
11
12
13
14
15
STABILITY CHAIR
ASSEMBLY INSTRUCTIONS
ASSEMBLY MANUAL
0681P-2 PRINTED IN CANADA. © 2003 MERRITHEW CORPORATION. ALL RIGHTS RESERVED. ™/® TRADEMARK OR REGISTERED TRADEMARK OF MERRITHEW CORPORATION, USED UNDER LICENSE.
stabilityCHAIR
2200 Yonge Street, #500, Toronto, ON, M4S 2C6 phone: [phone]
fax: [phone] email: [e-mail] website: www.merrithew.com
TROUBLESHOOTING
CHECKLIST
CHECK THAT...
■■all holes on wooden panels match
with metal frames, middle support
and chair handle receptacles
■■pop-up pins and stud knobs work
properly on handle receptacles
■■lock on split-pedal works properly

1ALL MODELS Take horizontal frame
complete with pedal [A] and fix
wooden sides [B] on each side with one
1/4"x 2" carriage bolt/nut [position 9]
ensuring the logo faces outward.
Do not tighten.
2ALL MODELS Slide vertical frame
[D] between the two wooden sides
[B] at the back, making sure the 1"
square tube with eyehooks faces out
and the holes for the chair seat face up.
Match the three holes on each side of
the wooden sides [B] with vertical frame
[D] and fix six 1/4"x 2" carriage
bolts/nuts [positions 1,2,3].
Do not tighten.
3ALL MODELS Fix middle support
[E] between the two wooden sides,
using two 1/4"x1-1/2" hex bolts with
washers on outside [position 4], making
sure holes for chair seat face up.
4aMODELS WITHOUT HANDLES Fix wooden sides to horizontal
frame with 1/4"x2" carriage bolts/nuts
[position 7,8]. Fix two 1/4"x1-1/2" hex
bolts/nuts [position 5,6] with washers
in remaining holes on wooden sides.
Tighten all hardware.
4bMODELS WITH HANDLES Fix bottom end of chair
handle receptacles [C] to wooden
sides and horizontal frame using two
1/4"x 2-1/4" hex bolts/nuts with
washers only on outside [position 7,8].
Fix top end of chair handle receptacles
to wooden sides using two 1/4"x1-1/2"
hex bolts/nuts with washers on both
sides [position 5,6]. Tighten all hardware.
5ALL MODELS Place chair seat [H]
on top of middle support [E] and
vertical frame [D]. Align evenly along
wooden sides and fix four 1/4"x2"
hex bolts with washers [10,11,12,13],
from bottom to hold chair seat on frame.
Tighten all hardware.
6MODELS WITH HANDLES
Assemble chair handles [F]
and chair handle chrome extensions
[G] each with two 3/8"x3/4"
hex bolts [14,15] with washers
and tighten.
Note: Chair handles and chrome
extensions come as right and left.
7MODELS WITH HANDLES Loosen
round stud knob [17]. Pull pop-up
pin [16] and insert complete chair
handle [F,G] into chair handle receptacle
[C]. Ensure bolt head at [15] faces out.
Release pop-up pin at desired height
and tighten round stud knob [17] to
secure handle in receptacle. Adjust
handle height following same procedure.
Note: To prevent damage to vinyl on chair
seat make sure bolt head at position #15
faces away [out] from the chair.
8ALL MODELS Attach all springs;
heavy springs [18] to inner
eyehooks and light springs [19]
to outer eyehooks.
Note: Attach springs to hooks on pedal
first, then to hooks on vertical frame.
9SPLIT PEDALS To split pedals:
Loosen both star knobs [21]
and lift open side of lock [20] from
star knob and rotate so it is completely
under one pedal. Tighten both
star knobs.
To join pedals: Loosen both star
knobs [21] and rotate lock [20] to
hook onto metal shaft of star knob.
Tighten both star knobs.
STABILITY CHAIR
ASSEMBLY INSTRUCTIONS
IMPORTANT: DO NOT TIGHTEN ANY BOLTS OR SCREWS PRIOR TO FINISHING COMPLETE ASSEMBLY.
FOR SAFETY REASONS: DO NOT LIFT CHAIR FROM CHAIR SEAT, GRIP METAL FRAME INSTEAD.
SPECIAL
FEATURES
ALSO
AVAILABLE
adjust spring tension with easy
hook-on system
lock split-pedal together for use
as a single pedal
shoponlinewww.merrithew.com
D
20
19
18
21
STABILITY CHAIR DVDS
Enhance your performance
with any or all of our videos
that coach you through each
level of core stability training.
WALL CHART
A great way to support client
instruction and brighten up
your studio or gym.
WARNING: As with any athletic activity, the use of exercise equipment involves risk of injury, damage and/or death. By choosing to use STOTT PILATES equipment,
you and/or your clients/patients assume responsibility for that risk, not the people who sold you the equipment, distribute it and/or manufacture it.
To prevent unsafe or improper use of STOTT PILATES equipment, please read all assembly and safety information thoroughly and follow the directions carefully. Contact the
manufacturer if you have any questions or concerns. Please also ensure that you and your clients/patients have received proper instruction regarding the correct and safe use
of STOTT PILATES equipment.
Like any mechanical device, Pilates equipment and its components are subject to wear and stress. Proper maintenance and timely replacement of your equipment or component
parts is your responsibility as it helps reduce the risk of injury. As it is impossible to predict every situation and condition that will occur while using STOTT PILATES equipment,
Merrithew Health and Fitness™makes no representation about the safe use of its equipment under all conditions.
COURSE MANUAL
Details the full Stability Chair
repertoire including exercise
descriptions and photographs.
Call or email today for
more information.