Merrithew Reformer Parts list manual

For video assembly
instructions, visit
merrithew.com/
eq-assembly
Please review this important assembly and warranty information about your replacement
MERRITHEW™equipment parts and keep it handy for future reference.
Reformer
Spring Replacement
REPLACEMENT GUIDE

Reformer Spring Replacement Guide2
3. Using second 7⁄16" wrench on opposite side, loosen nylon
locknut. This may require a bit of torque force. Discard used nylon
locknuts. New ones are provided with newsprings.
5Repeat steps 2 to 4 on remaining springs.
4. Remove spring bolt from spring anchoring bar,
thenpull ball end of the spring out of holder.
2. With 7/16" wrench or pliers, hold fixed cube nut in place.1. Remove carriage. Find full instructions on page 22
ofyourReformer Owner's Manual or view video online at
merrithew.com/support/equipment-manuals-assembly
Removing Springs
Important: Read full instructions before beginning.
For step-by-step video instruction visit merrithew.com/eq-assembly
Bolt End of Spring
Ball End of Spring
NYLON LOCKNUTSPRING BALL SPRING COILS SPRING SLEEVE SPRING BOLTFIXED CUBE NUT
6. Affix the sticker provided with your spring replacement
package to the underside of the Carriage.
REMOVAL & INSTALLATION IMPORTANT
Replace all springs every 24 months and spring clips
every 12 months, or as needed within that period.
FAILURE TO PERFORM RECOMMENDED SAFETY
CHECKS, OR USING EQUIPMENT WITH IMPROPERLY
ADJUSTED, BROKEN OR WORN PARTS, COULD RESULT
IN SERIOUS BODILYINJURY.

3
Installing New Springs
3. Insert spring bolt through the corresponding hole on
springanchoring bar.
4. Thread nylon locknut onto spring bolt.
7. Repeat steps 1 to 6 for remaining springs 8. Replace carriage. Find full instructions on page 23 of
yourReformer Owner's Manual or view video online at
merrithew.com/support/equipment-manuals-assembly
6. Both nylon locknut and fixed cube nut should be snugup
against spring anchoring bar.
CAUTION: Do not overtighten. Doing so could cause the spring
anchoring bar to collapse.
5. Hold fixed cube nut in place with 7⁄16" wrench.
Usingsecond 7⁄16" wrench, tighten nylon locknut.
NOTE: Do not reuse old nylon locknuts.
1. Remove nylon locknut from spring bolt. 2. Insert the spring through the spring holder.
Required Tools
2 Open End Wrenches, 1/2"(13mm) x 7/16"(14mm)
Open End
Wrench
Phillips
Screwdriver
Pliers or
Vice Grips
+ +
or

THE FINE PRINT
Warranty
MERRITHEW™warrants that all new equipment is free of manufacturing defects in workmanship and materials, subject to the terms below.
Thiswarranty becomes effective at the invoice date of the original purchase. Parts repaired or replaced under the terms of this warranty
willbe warranted for the remainder of the original warranty period.
It is the purchaser’s responsibility to notify the Company of any change of contact information. This ensures, that in the unlikely event
ofareplacement or safety notice, we are able to contact you immediately.
This warranty applies to equipment only:
w While it remains in the possession of the original purchaser and proof
of purchase is demonstrated
wIf claims are made within the part-specific warranty period
w If upgrades are made as required by MERRITHEW
This warranty shall be null and void if:
w Equipment failure is a result of improper assembly,
installationormaintenance
w The equipment is used for any other purpose other than as
intended, or is stored or used outdoors, or in environments
without adequate climate/humidity controls
wEquipment has been subjected to accident, misuse, abuse,improper
service, or any modification not authorizedbyMERRITHEW
This warranty does not cover damage to the finish of any equipment
nor shipping charges, customs clearance fees (if applicable), or any costs
incurred in installing repaired or replacement parts shipped under the
provisions of this warranty.
Two (2) Year Limited Warranty
MERRITHEW will, at its option, repair or replace springs that fail for any
reason, provided such failure is reported to MERRITHEW within a period
oftwo years from the invoice date of the original purchase.
Failure to change springs every two (2) years may void warranty.
One (1) Year Limited Warranty
On all spring clips.
We recommend that spring clips (including those attached to traditional-
style ropes) be changed annually
Disclaimer of Implied Warranties and LimitationofRemedies
Repair or replacement of defective parts is your exclusive remedy under
the terms of this limited warranty. In the event of parts availability issues,
MERRITHEW will not be responsible for any consequential or incidental
damages arising from the breach of either this limited warranty or any
applicable implied warranty, or for failure or damage resulting from acts
ofnature, improper care and maintenance, accident, alteration, replacement
of parts by anyone other than MERRITHEW, misuse, transportation, abuse,
hostile environments (inclement weather, acts of nature), improper
installation or installation not in accordance with local codes or
printedinstructions.
This limited warranty is the sole express warranty given by
MERRITHEW. No product performance, specification or description
wherever appearing is warranted by MERRITHEWexcept to the
extent set forth in this limited warranty. Any implied warranty
protection arising under the laws of any state, provinceor territory
including implied warranty of merchantability or fitness for a
particular purpose, oruse, is hereby limited in duration to the
duration of this limited warranty.
Neither distributors, dealers, web resellers, nor the retailers selling this
product have any authority to make any additional warranties or to
promise remedies in addition to, or inconsistent with those stated above.
MERRITHEW’s maximum liability, in any event, shall not exceed the purchase
price of the product paid by the originalpurchaser.
2200 Yonge Street, Suite 500, Toronto, Ontario, Canada M4S 2C6
416.482.4050 | 1.800.910.0001 | 0800.328.5676 UK | ext. 0907
[email protected]om | merrithew.com
P00178-03 PM-P0002A FEB17 ™/® Trademark or registered trademark of Merrithew Corporation, used under license. Printed in Canada. All rights reserved.
*US Patent No. 7857736, 5792033, 2179793 and other US and foreign patents pending.
IMPORTANT
Please keep this guide in a safe place.
If you have questions, issues or are missing parts:
Please contact customercar[email protected]
416.482.4050 |1.800.910.0001 |0800.328.5676 UK |ext. 0907