Merrithew Spx reformer stott pilates User manual

Please review this important assembly, safety and warranty information about

your new STOTT PILATES®equipmentand keep it handy for future reference.

Owner’sMANUAL

Part Identification for STOTT PILATES®SPX®

1 Star Knobs 1/2"

2 Accessory Board Receptacles

3 Easy-Roll Wheels

4 Wooden Standing Platform

5 Gearbar Slots [fig. B]

6 Springs [fig. B]

7 Footbar

8 Swing Arm Support

9 5/16" Socket Head Cap Screws

10 Spring Sleeves

11 Footbar Adjustment Cradles

12 Plastic Spring Holder [fig. E]

13 Small Swing Arm Bars

14 Large Swing Arm Bars

15 Aluminum Rails

16 Carriage

17 Adjustable Headrest

18 Shoulder Rests

19 Double Loop Straps [fig. F]

20 Serial Number Sticker

21 Star Knobs 3/8" [fig. C & G]

22 Ropes

23 Pulleybars

24 Stand Up Pulley Springs

25 Pulleys

26 Gearbar [fig. B]

27 Chrome Tubes [fig. C]

28 5/8" Bronze Bushings [fig. D]

29 Floating Roller & Rod System [fig. D]

30 Fixed Rollers [fig. E]

31 Rubber Carriage Stopper [fig. A]

32 Carriage Stopping System [fig. A]

33 Stopper Plates

34 Pulleybar Receptacles [fig. G]

Reformer

REQUIRED TOOLS:

ONE FLAT-HEAD SCREWDRIVER

ONE 1/4" (6MM) HEX KEY (SUPPLIED)

ONE OPEN-END WRENCH (SUPPLIED)

1/2" (13MM) X7/16" (11MM)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

User’s Guidelines

The STOTT PILATES SPX®Reformer is a sophisticated

piece of Pilates equipment that, when used properly,

can facilitate many Pilates exercises safely and

effectively. However, care and caution must be taken

as there are some inherent dangers when using

any exercise equipment – especially when spring

resistance is involved.

For inexperienced or first-time users,

the STOTT PILATES SPX Reformer should

only be used under the supervision

of a trained professional.

This STOTT PILATES SPX Reformer Owner’s Manual

includes general guidelines for setup and usage.

To get the most out of your Reformer, STOTT PILATES

offers a full range of instructional DVDs and Manuals.

Personalized training is offered through our Licensed

and Corporate Training Centers or from Certified

STOTT PILATES instructors.

Mechanical

Safety Check

Proper maintenance and timely replacement

of your equipment or component parts is

your responsibility. Conduct a regular

inspection of the following:

Daily:

◗Check wear on ropes, replace as needed.

◗Clean rails with damp soft cloth.

◗Ensure shoulder rests are fully seated on carriage

◗Clean all upholstery areas after each use, using a

soft cloth and gentle cleanser.

Weekly:

◗Ensure that all nuts, bolts and screws are secure

and tight.

◗Ensure plastic feet are securely attached and have

the flat side facing towards the floor.

◗Ensure footbar is level and not spinning.

◗Ensure swing arm supports are securely fastened.

◗Inspect and confirm pulleybar star knobs are

securely tightened.

◗Ensure eyehooks are aligned parallel to the rails.

◗Inspect rollers for excessive wear, replace as needed.

◗Sit on carriage and test roll, listen for any thumping

or grinding – it should be a quiet ride.

◗Check all springs for wear and damage,

replace immediately as needed.

Monthly:

◗Check rope wear and replace as necessary.

◗Check that spring bolts and spring balls are

securely fastened.

◗Check all spring clips to ensure proper fastening.

◗Check star knobs for wear and replace as necessary.

◗Check strap wear and replace as necessary.

Yearly:

◗Replace all spring clips

Every 2 years:

◗Replace all springs

Refer to the assembly section in this manual

for initial assembly instructions and part labeling.

FAILURE TO PERFORM RECOMMENDED SAFETY

CHECKS, OR USING THE MACHINE WITH IMPROPERLY

ADJUSTED, BROKEN OR WORN PARTS COULD

RESULT IN SERIOUS BODILY INJURY.

IMPORTANT!

This manual contains important assembly, safety and

usage information. Read the manual carefully before

using your new STOTT PILATES®SPX®Reformer*and

keep the manual handy for future reference.

UNSAFE OR IMPROPER USE OF THIS EQUIPMENT

BY FAILING TO READ AND COMPLY WITH ALL

REQUIREMENTS AND WARNINGS COULD RESULT

IN SERIOUS INJURY.

It is impossible to predict every situation and

condition which can occur while using your Reformer.

STOTT PILATES makes no representation about the

safe use of the Reformer under all conditions. There

are risks associated with the use of any exercise

equipment which cannot be predicted or avoided,

and you assume the responsibility for that risk.

STOTT PILATES recommends cautious assembly and

usage and wishes you many hours of safe and

effective exercise.

IMPROPER USE OF EXERCISE EQUIPMENT

MAY CAUSE SERIOUS INJURY. TO REDUCE RISK,

PLEASE READ THE FOLLOWING:

Reformer Safety:

◗Before starting any exercise program,

consult a physician.

◗Use equipment for intended exercises only.

◗Before moving a STOTT PILATES®Reformer,

ensure springs are attached so carriage is

secure and ropes do not drag.

◗Ensure the equipment is properly adjusted for

your size and ability level.

◗Stop exercising immediately if you experience

chest pain, feel faint, have difficulty breathing

or experience any discomfort.

◗Keep body, clothing and hair free from all moving parts.

◗Do not use if equipment appears worn,

broken or damaged.

◗Do not attempt to repair equipment yourself.

◗Do not allow children to use or be around

equipment without adult supervision.

◗For optimal performance, allow at least two

feet of clear space on either side of a

STOTT PILATES Reformer.

GETTING ON THE REFORMER

STOP! Before getting on, ensure that at least

one spring is securely attached to the gearbar!

Standing or Kneeling Positions

The carriage is a moving platform. Special attention

must always be paid to maintaining your balance

and stability, especially when performing kneeling

or standing exercises. See cautions above.

1Before you begin, ensure that one or more

springs are engaged in the gearbar to secure

the carriage.

2Step carefully with one foot onto carriage –

a gripper mat may be used to prevent slipping.

[Gripper mat not supplied, see replacement parts,

page 10].

3Place other foot carefully onto the wooden

standing platform.

NEVER stand with both feet on

wooden standing platform.

Secure Hands & Feet

Whenever placing hands or feet on the footbar,

shoulder rests or headrest, ensure they will not

slip during exercise. Gripper mats may be used.

CAUTION

SUPINE POSITION (lying on back)

1Sit on Reformer carriage, legs off to one side.

2Reach hand nearest the footbar across your

body and place it onto the shoulder rest.

3Tuck opposite shoulder under arm and roll

onto back lowering head onto headrest.

4Bring legs up and place feet on footbar

lowering arms by side.

1Insert gearbar [26] into middle gearbar slot [5]

with the concave indentations facing wooden

standing platform [4] [see inset].

3NOTE: With two people, tilt Reformer onto one side.

As one person steadies Reformer, insert free ends

of ropes [22] through back of pulleys [25], then

through chrome tubes [27] underneath carriage.

2Insert pulleybars [23] into receptacles [34] at rear

of Reformer and tighten star knobs at base of

receptacles. Ensure eyehooks on top of pulleybars

are parallel to aluminum rails [15] and that star

knobs are fully tightened so there is no movement

of the pulleybars.

Assembly Instructions

4Tie a knot leaving a 6-8" tail to prevent ropes

from passing back through chrome tubes.

12 Place double loop straps [19] on carriage so

D-rings on straps line up with back of metal plate

of shoulder rests.

Subtle adjustments can be made to length of

ropes by sliding chrome tubes [27]. Secure by

tightening star knobs [21].

5Return Reformer to upright position.

7Ensure shoulder rest pommel handles are positioned

to the outside of the shoulder rest frames.

8Place ¼” black washers over the shoulder rests

screw hole slots.

6Position shoulder rests directly over screw holes.

9Insert ¼”-20 x 1 ¼” screws through washers and

into top of screw holes.

10 Use the 1⁄8” Allen key provided to tighten, ensuring

the shoulder rests are secure.

11 To determine correct length of ropes, set carriage

stopper in second hole from footbar. Engage

spring (6) in gearbar (5) so carriage (16) does not

move.

Safety & Usage

GEARBAR

The gearbar position determines the amount of initial

tension on the springs. The slot closest to the wooden

standing platform is position #1; the next is position

#2; the next is position #3. Lower position numbers

provide higher spring tension.

Adjusting the Gearbar

◗Do not sit on carriage while adjusting.

◗Remove all springs from gearbar.

◗Place gearbar in desired position.

◗Ensure gearbar slides fully into slots.

◗Ensure concave indentations face toward footbar.

Position gearbar relative to the carriage to create initial

tension on the springs, i.e. the gearbar should not be

in position #3 if the carriage stopper is in position #1

or #2 as there will not be any spring tension.

CARRIAGE STOPPER

The carriage stopper position determines how close

the carriage slides in toward the wooden standing

platform and dictates the range of motion required

of the body’s joints. The hole closest to the wooden

standing platform is referred to as position #1;

the next hole is position #2, etc.

Adjusting the Carriage Stopper

◗Do not sit on carriage while adjusting.

◗Remove all springs from gearbar.

◗Insert carriage stopper in one of six positions.

◗Be sure carriage stopper is completely

inserted in the hole and is not loose.

The carriage stopper position should usually be

selected so that when lying supine (on your back),

with heels on the footbar, there is a 90 degree

angle of flexion at the hip joint when the carriage

is against the carriage stopper. If injury, disease or

other limitations restrict flexion at the hips or knees,

adjust the carriage stopper by placing it farther out.

Adjustments can also be made for the exercise

being performed.

NOTE: The carriage stopper must be inserted in one

of the six positions AT ALL TIMES. Using the Reformer

without the carriage stopper may cause damage to

the gearbar assembly or rollers.

#6 #5 #4 #3 #2 #1

SPRINGS

REPLACE ALL SPRINGS EVERY 24 MONTHS.

The number of springs attached to the gearbar

determines the total amount of resistance.

SPX®Reformers are equipped with four

100%-tension springs, and one 50% spring.

Adjusting Springs

◗Take care when attaching and detaching springs.

◗For safety, place one hand on gearbar.

◗Firmly grasp spring (not the ball on the spring)

and stretch it to hook to or unhook from gearbar.

◗Ensure ball end rests securely in concave

indentations of gearbar.

FOOTBAR

The footbar can be set at four different heights

to facilitate various Reformer exercises and to

accommodate physical differences and abilities.

The cradle closest to the gearbar is position #1

the cradle farthest away is position #4.

Adjusting the Footbar

◗The footbar can be adjusted while standing

beside the Reformer or sitting on the carriage.

◗Gently pull footbar up and lift swing arm

support out of footbar adjustment cradle.

◗Lift or lower footbar to the desired height

and place swing arm support securely

into nearest footbar adjustment cradle.

NOTE: It is highly recommended that the Reformer be

placed on some type of non-skid material to prevent

slipping and/or damage to flooring or carpet.

HEADREST

The headrest adjusts to three positions: flat,

half-raised or fully raised. It should be adjusted on

an individual basis to ensure neck and shoulders

are comfortable and tension-free when lying supine.

In exercises where the hips are lifted higher than

the shoulders, headrest should be flat – even when

beginning from a supine position. In some exercises

it is raised to provide a brace for the feet.

Adjusting the Headrest

◗With no weight on headrest, lift it and hinge

adjustment block to rest securely onto wooden

edge of carriage.

MOVING REFORMERS

The front end of all Reformers have a set of easy-roll

wheels that make moving or repositioning simple for

anyone of moderate strength.

◗Ensure springs are attached so carriage is secure,

and ropes do not drag.

◗Stand at the back of Reformer, grasp the horizontal

metal bar, and gently lift. Lift Reformer high enough

to engage easy-roll wheels.

◗Keep Reformer at waist-height or lower. Do not lift

higher as this may result in damage to floor surface.

#1 #2 #3 #4

Care & Cleaning

We recommend wiping the vinyl surface with a mixture

of water and tea tree oil, a natural disinfectant available

at most pharmacies or health food stores. Add 1tsp

of tea tree oil to a 1L or 1qt spray bottle of water.

A mixture of mild soap and water can be used to

remove more persistent dirt. Ensure cleaner does

not leave an oily residue, or make surfaces slippery.

The inside of the aluminum rails and rollers should

be cleaned weekly with window cleaner and a cloth.

Spray cleaner onto cloth first, avoid spraying directly

onto surfaces, rollers or aluminum rails.

CAUTION: Never use oil lubricants as they

may damage rollers.

FLOATING ROLLERS

With carriage removed from rails, slide floating rollers

into bronze bushings. Then follow directions for replacing

carriage [on page 16].

CAUTION: Never use oil lubricants as they

may damage rollers.

FIXED ROLLERS

With carriage removed from rails, attach fixed roller

with the aid of a ratchet and 1/2" socket attachment.

Ensure fixed rollers are securely fastened. Follow

directions on removing carriage [on pg 12] and

replacing carriage [on page 16].

Traditional Spring Package (5 Springs) ST-05057

High-Precision Spring Package (5 Springs) ST-05058

Basic Spring Package (4 Springs) ST-05070

Footbar – SPX (Double) ST-05069

Padded Platform Extender – SPX ST-02074

Reformer Ropes (pair) ST-06016

Fixed Rollers (pair) ST-06013

Floating Rollers (pair) ST-06014

Carriage Stopper ST-06012

Reformer Box Footstrap ST-02018

Spring Sleeve ST-05070

Shoulder Rests (pair) ST-02023

Spring Clip ST-02020

Foam-Grip Handles (pair) ST-02007

Padded Long Spine Straps (pair) ST-02016

Soft Reformer Loops (pair) ST-02009

Maple Roll-Up Pole ST-06008

Gripper Mat ST-02022

Floating Roller

Bronze Bushing

Replacement and optional parts:

Replacement Parts

1312

2Using a flat head screwdriver, remove stopper plates.

Steps to Removing and Replacing Springs

1To remove carriage, remove pulleybars and place on

the floor, on either side of the aluminum rails.

4Place carriage face-down on the ground.

NOTE: Ensure it is placed on a soft surface that

will not scrape vinyl.

2Using second 7/16" wrench on opposite side

of spring anchoring bar, loosen nylon locknut.

This may require a bit of torque.

NOTE: DISCARD used nylon locknuts. (New nylon

locknuts are provided with new springs.)

3Remove spring from spring anchoring bar.

1With 7/16" wrench, hold fixed cube nut in place.

4Pull spring out of the plastic spring holder.

Step 2. Removing SpringsStep 1. Removing Carriage

3NOTE:Requires two people.

Carefully slide carriage out of the aluminum rails

keeping carriage level until completely free of rails.

Turn carriage over ensuring rollers are secure and

do not come in contact with the floor.

5Repeat steps 1 to 4 on remaining springs. 6Remove spring sleeves from old springs

and slide onto new springs, if applicable.

REQUIRED TOOL:

FLAT-HEAD

SCREWDRIVER

REQUIRED TOOLS:

TWO OPEN-END WRENCHES

1/2" (13MM) X7/16" (11MM)

Spring Anchoring Bar

Fixed Cube Nut

1514

Place 50% spring in the center and two

100% springs on either side.

1Starting with spring #1 from your spring package,

remove nylon locknut from bolt end of spring.

2Start at one end of the carriage. Thread bolt end of

spring #1 through first hole of plastic spring holder.

Place 50% spring in the center, and 25% spring to

one side. Place 100% springs in remaining positions.

4Thread nylon locknut into spring bolt.

3Insert spring bolt through the corresponding hole

on spring anchoring bar.

Step 3. Installing New Springs

5Hold fixed cube nut in place with 7/16" wrench.

Using second wrench, tighten the new nylon locknut.

NOTE: DO NOT REUSE old nylon locknuts.

100 100100 10050 100 10050 10025

if this set purchased start here:

#1#2#3#4#5#1#2#3#4#5

6Both nylon locknut and fixed cube nut should be

snug against the spring anchoring bar.

7Repeat steps 1 to 6 for remaining springs.

TRADITIONAL SPRING PACKAGE

4X100%, 1 X50% arrange as follows:

HIGH-PRECISION SPRING PACKAGE

3X100%, 1 X50%, 1 X25% arrange as follows:

NOTE: SPX®Reformers arrive with four 100% springs, and one 50% spring.

Replacement spring packages are also available.

Determine replacement spring package.

Springs are color-coded at the ball end. Red = 100%, Blue = 50%, White = 25%

100 10025 10050

#1#2#3#4#5

HIGH-PRECISION SPRING PACKAGE

3X100%, 1 X50%, 1 X25% arrange as follows:

Leaving middle position free, place 100% springs

in remaining positions on the carriage, as illustrated

on right. Install 50% spring in the center.

100

#1#2#3#4

SPX SPRING PACKAGE

4X100% arrange as follows:

100 100 100

REQUIRED TOOLS:

FLAT-HEAD SCREWDRIVER

TWO OPEN-END WRENCHES

1/2" (13MM) X7/16" (11MM)

NOTE: Spring sleeves are required for proper function

of this Reformer if it features a plastic spring holder.

8Write date of installation on the sticker provided

with spring replacement package. Affix sticker

on the underside of Reformer carriage.

Springs should be replaced every 24 months,

or as needed within that period.

1716

Step 4. Replacing Carriage

2Wipe inside of aluminum rails with window

cleaner and/or a dry cloth to remove dust or dirt.

Spray cleaner onto cloth first. Avoid spraying

directly onto surfaces, rollers or aluminum rails.

Insert carriage stopper in one of six positions.

1Remove carriage stopper.

3Ensure that pulleybars are still on the floor on either

side of aluminum rails. Carefully turn carriage to its

side while ensuring rollers never come in contact

with the floor. Now, prepare for another person

to take hold of opposite side of the carriage.

4Slide rollers into c-channels.

NOTE: To prevent damaging rollers, it is strongly

advised two people hold carriage. One person guides

rollers carefully into channels while the other

supports opposite side of carriage. Once rollers

are secured in channels, guide carriage into place.

6Using a flat head screwdriver, replace stopper plates.

5 CAUTION: When guiding carriage straight into

aluminum rails, move slowly and carefully as the

rollers are sensitive. Once rollers are within rails

they are protected.

7Insert pulleybars into receptacles at rear of Reformer

and fully tighen star knobs so pulleybars are secure.

Ensure eyehooks on top of pulleybars are parallel

to aluminum rails.

8Replace gearbar and engage springs before resuming

use of your Reformer.

REQUIRED TOOL:

ONE FLAT-HEAD

SCREWDRIVER

1918

PADDED PLATFORM EXTENDER

Extends the wooden standing platform to

accommodate a variety of exercises, providing

added comfort and safety. Can also be used

on the carriage to bring the pelvis and spine

to a neutral position when sitting.

◗Remove footstrap (if applicable) and

lower footbar completely.

◗Place desired springs in gearbar.

◗Place padded platform extender on rails ensuring

it is firmly in place against wooden standing

platform and does not move.

◗Gripper mats may be used.

GETTING ON THE REFORMER

STOP! Before getting on, ensure that at least

one spring is securely attached to the gearbar!

Standing or Kneeling Positions

The carriage is a moving platform. Special attention

must be paid to maintain balance and stability,

especially when performing kneeling or

standing exercises.

1Ensure that one or more springs are engaged

in the gearbar to secure the carriage.

2Step with one foot onto carriage – a gripper mat

may be used to prevent slipping.

[Gripper mat not supplied, see replacement parts,

page 10].

3Place other foot on the wooden standing platform.

NEVER stand with both feet on

wooden standing platform.

GRIPPER MATS

Versatile non-slip mats are handy to increase

traction and prevent slipping or sliding

(see image above for example of usage).

Optional Reformer Accessories

MAT CONVERTER

Adding a mat converter creates a safe,

stable surface for matwork.

Installing the Mat Converter

◗Remove footstrap (if applicable).

◗Place footbar down and disconnect springs.

◗Slide carriage back against pulleybars, ensuring

ropes are wrapped out of the way.

◗Insert mat converter ensuring it is pressed

completely into place.

ACCESSORY BOARDS

Optional accessory boards can be added to

SPX Reformers to further increase exercise options.

◗Jumpboard and Cardio-Tramp™for plyometric

and aerobic exercises.

◗Rotational Diskboard™for controlled internal

and external rotation.

◗Rotational Diskboard Deluxe™allows greater

range and asymmetrical movements when

working in controlled rotation.

◗Soft footbar accommodates sensitive feet.

Installing Accessory Boards

◗Lower footbar to lowest position.

◗Insert accessory board into receptacles in wooden

standing platform and ensure it slides down fully.

◗Tighten star knobs located under

wooden standing platform.

FOOTSTRAP

Footstrap is included with purchase of a Reformer box.

Attaching the Footstrap

◗Loop footstrap around wooden standing platform

and adjust the length by attaching spring clip to one

of the three D-rings.

◗Footstrap should be adjusted so that there is

tension with knees slightly flexed. It is important

to keep feet hooked securely under footstrap.

REFORMER BOX

Reformer boxes can be used to facilitate or

modify exercises.

Positioning the Reformer Box

◗Place Reformer box on top of carriage with either

long or short side facing forward.

◗Box can be placed over or against shoulder rests

in the “short box” position.

METAL ROLL-UP POLE

Perfect to provide added scapular awareness,

it can be used with multiple Reformer exercises.

212020

Warranty

STOTT PILATES®REFORMERS

Merrithew Health & Fitness™warrants that all new Reformer products are free of manufacturing defects in workmanship and

materials, subject to the terms below. This warranty becomes effective at the invoice date of the original purchase. Parts repaired

or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period.

This warranty applies to the SPX and Club SPX Reformers only:

◗While equipment remains in the possession of the original purchaser and proof of purchase is demonstrated

◗If claims are made within the part-specific warranty period

◗If upgrades are made as required by Merrithew Health & Fitness

THIS WARRANTY SHALL BE NULL AND VOID IF:

◗Reformer springs are not changed every two (2) year

◗All safety and usage guidelines as specified in the appropriate equipment manuals are not followed

◗The equipment is used for any other purpose other than as intended

◗If equipment failure is a result of improper maintenance

◗If equipment has been subjected to accident, misuse, abuse, improper service, or any modification not

authorized by Merrithew Health & Fitness

This warranty does not cover damage to the finish of any STOTT PILATES equipment, or shipping charges, customs clearance fees

(if applicable) or any costs incurred in installing repaired or replacement parts shipped under the provisions of this warranty.

LIMITED LIFETIME WARRANTY (AT HOME AND SPX MODELS)

On aluminum rails, components of the frame and related welding, Gearbar, and Footbar mechanisms (excluding Rubber Footbar)

when used in a home or non-commercial setting.

TEN (10) YEAR LIMITED WARRANTY (CLUB AND SPX MODELS)

Merrithew Health & Fitness will, at its option, repair or replace any of the parts listed below,

provided that the part(s) fail due to a defect in workmanship or materials:

◗Aluminum rails

◗Components of the frame and related welding

◗Gearbar

◗Footbar mechanism

FOR SPX®

, AT HOME SPX®AND CLUB SPX®MODELS:

ONE (1) YEAR LIMITED WARRANTY

On wear and tear items including ropes, straps, spring clips, plastic pulley bar receptacle sleeves, non skid tape on footbar,

spring covers and plastic spring holders.

TWO (2) YEAR LIMITED WARRANTY

On all other Reformer components. Merrithew Health & Fitness, at its option, repair or replace warranted parts, provided that

these part(s) fail due to a defect in workmanship or materials and provided such failure is reported to Merrithew Health & Fitness

within the part-specific warranty period.

90-DAY UPHOLSTERY FABRIC WARRANTY

The vinyl fabric upholstery on your STOTT PILATES Reformer will be replaced if it fails to give normal wear for 90 days

after delivery. Proof of damage may be required. This warranty does not cover cuts, burns, stains, soiling, pet damage, damage to

fabric caused by abrasive, corrosive or chemical cleansers, or damage caused by other unreasonable use. If the identical fabric is

not available, Merrithew Health & Fitness will provide an equivalent fabric.

DISCLAIMER OF IMPLIED WARRANTIES AND LIMITATION OF REMEDIES

Repair or replacement of defective parts is your exclusive remedy under the terms of this limited warranty. In the event of

parts availability issues, Merrithew Health & Fitness will not be responsible for any consequential or incidental damages arising

from the breach of either this limited warranty or any applicable implied warranty, or for failure or damage resulting from acts

of nature, improper care and maintenance, accident, alteration, replacement of parts by anyone other than Merrithew Health

& Fitness, misuse, transportation, abuse, hostile environments (inclement weather, acts of nature), improper installation or

installation not in accordance with local codes or printed instructions.

This limited warranty is the sole express warranty given by Merrithew Health & Fitness. No product

performance, specification or description wherever appearing is warranted by Merrithew Health & Fitness

except to the extent set forth in this limited warranty. Any implied warranty protection arising under

the laws of any state, province or territory including implied warranty of merchantability or fitness for

a particular purpose, or use, is hereby limited in duration to the duration of this limited warranty.

Neither dealers, web resellers, nor the retailers selling this product have any authority to make any additional warranties or to

promise remedies in addition to or inconsistent with those stated above. Merrithew Health & Fitness maximum liability, in any

event, shall not exceed the purchase price of the product paid by the original purchaser.

Warranty

STOTT PILATES®REFORMERS

Merrithew Health & Fitness™warrants that all new Reformer products are free of manufacturing defects in workmanship and

materials, subject to the terms below. This warranty becomes effective at the invoice date of the original purchase. Parts repaired

or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period.

This warranty applies to the SPX®and Club SPX®Reformers only:

◗While equipment remains in the possession of the original purchaser and proof of purchase is demonstrated

◗If claims are made within the part-specific warranty period

◗If upgrades are made as required by Merrithew Health & Fitness

THIS WARRANTY SHALL BE NULL AND VOID IF:

◗Reformer springs are not changed every two (2) years

◗All safety and usage guidelines as specified in the appropriate equipment manuals are not followed

◗The equipment is used for any other purpose other than as intended

◗If equipment failure is a result of improper maintenance

◗If equipment has been subjected to accident, misuse, abuse, improper service, or any modification not

authorized by Merrithew Health & Fitness

This warranty does not cover damage to the finish of any STOTT PILATES equipment, or shipping charges, customs clearance fees

(if applicable) or any costs incurred in installing repaired or replacement parts shipped under the provisions of this warranty.

LIMITED LIFETIME WARRANTY (AT HOME AND SPX®MODELS)

On aluminum rails, components of the frame and related welding, gearbar, and footbar mechanisms (excluding rubber footbar)

when used in a home or non-commercial setting.

TEN (10) YEAR LIMITED WARRANTY (CLUB AND SPX®MODELS)

Merrithew Health & Fitness will, at its option, repair or replace any of the parts listed below,

provided that the part(s) fail due to a defect in workmanship or materials:

◗Aluminum rails

◗Components of the frame and related welding

◗Gearbar

◗Footbar mechanism

FOR SPX®

, AT HOME SPX®AND CLUB SPX®MODELS:

ONE (1) YEAR LIMITED WARRANTY

On wear and tear items including ropes, straps, spring clips, plastic pulleybar receptacle sleeves, non-skid tape on footbar,