Metra Electronics 95-7418 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-7418
Flat Blade Screwdriver I Phillips Screwdriver
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
•DDIN Head Unit Provision
•STACKED ISO DIN Head Unit Provision
A) Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
95-7418
A
APPLICATIONS
2002-2004 Nissan Altima

Dash Disassembly ............................................................................ 1
Kit Assembly ................................................................................. 2-3
Final Assembly ................................................................................. 4
95-7418
TABLE OF CONTENTS

1
95-7418
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove the trim panel
surrounding the climate controls.
(Figure A)
2
2002-2004 NISSAN ALTIMA
Remove (1) Phillips screw (bottom
right side of panel) securing the
panel surrounding the radio then
unclip and remove the panel.
(Figure B,C)
3
Remove (4) Phillips screws securing
radio to remove. (Figure D)
4
Remove the screws securing the
factory brackets to the radio and
remove brackets. (Retain brackets
for re-use during kit assembly.)
5
DASH DISASSEMBLY
A
B
D
C

2
95-7418
KIT ASSEMBLY
Snap the 95-7418 trim plate into the
radio trim panel. (Figure A)
1
Install from rear
A
Slide the DDIN radio unit into the
factory brackets and secure the unit
to the brackets using the screws
supplied with the head unit.
(Figure
B)
2
DOUBLE DIN HEAD UNIT PROVISION
B

3
1
Slide the stacked ISO DIN units into
the factory brackets and secure the
units to the brackets using the
screws supplied with the head unit.
(Figure B)
2
STACKED ISO DIN HEAD UNIT PROVISION
95-7418
KIT ASSEMBLY
Install from rear
A
B
Snap the 95-7418 trim plate into the
radio trim panel.
(Figure A)

4
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
95-7418
FINAL ASSEMBLY
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’sspecifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS

5
95-7418
NOTES

95-7418 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST95-7418
REV. 09/06/07