Metra Electronics 99-2008 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-2008
99-2008
APPLICATIONS
Cadillac DTS 2006-2010
Cadillac SRX 2007-2009
KIT FEATURES
•DIN Radio Provisiion with Pocket
•ISO Mount Radio Provisiion with Pocket
• Double DIN Radio Provisiion
•Stacked ISO Mount Units Provisiion
A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Double DIN Trim Plate
•E) Double DIN Brackets • F) Pocket
KIT COMPONENTS
1-800-221-0932
©COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
A
D
CB
E
F
TOOLS REQUIRED:
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
•GMOS-LAN-01 - GM LAN Interface
2006-up
•GMOS-LAN-02 - GM LAN Amplified-
Interface 2006-up
•GMOS-LAN-05 - GM Digital LAN Amp
Interface With Onstar 2007-up
•Antenna Adapter:
40-CR10 - Chrysler/GM Antenna
Adapter 2002-up
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set

Dash Disassembly
Chevrolet
- CadillacDTS2006-2010............................... 1
- CadillacSRX2007-2009.............................. 2
Kit Assembly
DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 4
Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Final Assembly ...........................................6
TABLE OF CONTENTS
99-2008
•Refer also to the instructions included with the aftermarket radio.

99-2008 DASH DISASSEMBLY
Cadillac DTS 2006-2010
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the trim panel
around the radio, climate controls and
ac vents and above glove box.
(Figure A)
2
Remove (4) 9/32” screws securing
the a/c vent panel. Unplug and
remove the panel. (Figure B)
3
Remove (4) 9/32” screws securing the
climate controls. Unplug and remove
the climate controls. (FigureC)
4
Remove (4) 9/32” screws securing
the radio. Unplug and remove the
radio. (Figure D)
5
Continue to kit assembly.
A
B
C
D
1

2
99-2008 DASH DISASSEMBLY
Cadillac SRX 2007-2009
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove trim piece
between shifter and cup holders.
(Figure A
2
Unclip and remove the trim panel
around the radio, climate controls,
ac vents and front half of center
console. (Figure B)
3
Remove (3) 9/32” screws securing
the a/c vent panel and remove the
panel. (Figure C)
4
Remove (4) 9/32” screws securing
the climate controls. Unplug and
remove the climate controls.
(FigureD)
5
Remove (4) 9/32” screws securing
the radio. Unplug and remove the
radio. FigureE)
6
Continue to kit assembly.
A
B
C
D
E

99-2008 KIT ASSEMBLY
3
A
B
C
DIN RADIO PROVISION WITH POCKET
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
2
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Snap the pocket into the housing.
(Figure C)

99-2008 KIT ASSEMBLY
4
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radio
using the screws supplied with the
radio.
(Figure A)
1
Slide the radio into the radio housing
until it snaps into place. (Figure B)
2
Snap the trim plate onto the front of
the radio housing. (Figure B)
3
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Snap the pocket into the housing.
(Figure C)

99-2008 KIT ASSEMBLY
5
DOUBLE DIN RADIO PROVISION
Cut and remove the center bar from
the radio housing.
(Figure A)
1
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the Double DIN radio or stacked
ISO mount units into the bracket/radio
housing assembly then secure to the
assembly using the screws supplied
with the radio or ISO mount units.
(Figure C)
3
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Snap the Double DIN Trim plate onto
the front of the Radio Housing.
(Figure C)

99-2008 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative batteryterminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of anyunused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
6
REV.04/21/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-2008