Metra Electronics 99-5816 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-5816
99-5816
APPLICATIONS
FORD Focus
2008-2011
KIT FEATU ES
• DIN adio Provision with Pocket
• ISO Mount adio Provision with Pocket
• Double DIN adio Provision
• Stacked ISO Mount Units Provision
• Painted To Match Factory Dash
• A) adio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket • G) (2) Top Clips and (4) Middle adio Housing Clips
Wiring & Antenna Connections (sold seperately)
XSVI-5520-NAV - Ford Interface
AFSI-02 - if equipped w/ sync
70-5522 - Ford Sub Harness
KIT COMPONENTS
A
TOOLS EQUI ED:
Small Flat Blade Screwdriver/ Panel emoval Tool
• Phillips Screwdriver • Socket Set • Cutting Tool
1-800-221-0932
© COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION
www.metraonline.com
BDE
C
F
(2) TOP CLIPS (4) MIDDLE CLIPS
SIDE VIEW SIDE VIEW
G

Dash Disassembly
- Ford Focus 2008-2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1,2
Kit Assembly
- Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- DIN Mount Ra io Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4
- ISO Mount Ra io Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . .5
- Double DIN /Stacke ISO Mount Units Ra io Provision . . . . . . . . . . . . .6
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
TABLE OF CONTENTS
99-5816
Note:
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.

1
4
5
FORD FOCUS 2008-2011
95-5816 DASH DISASSEMBLY
Disconnect the negative battery termi-
nal to prevent an accidental short cir-
cuit.
1
Unclip and remove the trim panel sur-
rounding the shifter and including the
cup holders. (Figure A)
emove (2) 9/32” screws facing up
above the gauge cluster then unclip
and remove the trim panel surrounding
the gauge cluster. (Figure C)
Unclip and remove the trim panel
above the glove box. (Figure D)
Contin e on page 2.
2
emove (2) 9/32” screws from the bot-
tom edge of the factory radio trim
panel. (Figure B)
3
PASS
AIRBAG
OFF
PASS
AIRBAG
OFF
C
PASS
AIRBAG
OFF
D
B
A

2
95-5816 DASH DISASSEMBLY
Contin e to kit preparation.
Unclip and remove the vent panel at
the top of the factory radio trim panel.
(Figure E)
6
emove (4) T-20 Torx screws securing
the climate controls to the factory
radio trim panel assembly and
remove the controls from the assem-
bly. ( etain the screws and climate
controls for re-use during kit prepara-
tion.)
(Figure G)
9
emove (4) T-20 Torx screws securing
the accessory socket panel to the
factory radio trim panel assembly and
remove the socket panel from the
assembly. (Retain the screws and
accessory socket panel for re- se
d ring kit preparation.)
(Figure G)
10
Unclip and remove the passenger air
bag light and the switch panel blank
plates. ( etain the air bag light and
blank plates for re-use during kit
preparation.)
(Figure G)
11
Unclip the factory radio trim panel
assembly. Unplug and remove the
assembly. Note: Some early models
had a gro nd strap attached to the
radio chassis and the s b dash with
an 8 MM bolt. Yo will need to nbolt
this strap to remove the factory radio
trim panel assembly.
8
emove (2) 9/32” screws behind the
vent panel removed in step 6.
(Figure F)
7
FORD FOCUS 2008-2011
1234 5
7 8 9 0
6
G
F
E

3
99-5816 KIT ASSEMBLY
KIT PREPARATION
1
Secure the climate control into the
radio housing using the factory hard-
ware. ( Figure A)
2
Secure the accessory socket panel to
the radio housing using the factory
hardware. (
Figure B)
3
Clip the passenger air bag light and
the switch panel blank plates in to
the radio housing. (
Figure C)
4
Attach Top and Middle adio Housing
Clips to the back of the radio housing.
(
Figure D,E)
NOTE: When the clips are properly
attached they sho ld be on a 90
degree angle with the radio ho sing.
C
(4) MIDDLE CLIPS
SIDE VIEW
(2) TOP CLIPS
SIDE VIEW FRONT VIEW FRONT VIEW
D
E
B
A

99-5816 KIT ASSEMBLY
4
A
B
C
DIN MOUNT RADIO PROVISION ITH POCKET
Slide the DIN cage into the radio hous-
ing and secure by bending the metal
locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the DIN
cage and until it snaps into place.
2
Snap the pocket into the radio housing.
(Figure C)
3
Contin e to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-5816 KIT ASSEMBLY
5
A
B
C
ISO MOUNT RADIO PROVISION ITH POCKET
Mount the ISO Brackets to the radio
using the screws supplied with the
radio.
(Figure A)
1
Slide the radio into the radio housing
until it snaps into place.
(Figure B)
2
Snap the trim plate onto the front of
the adio Housing. (Figure B)
3
Snap the Pocket into the radio
housing. (Figure C)
4
Contin e to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-5816 KIT ASSEMBLY
6
DOUBLE DIN/STACKED ISO MOUNT
UNITS RADIO PROVISION
Cut and remove the center bar from
the radio housing.
(Figure A)
1
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the Double DIN or stacked ISO
mount unit(s) into the bracket/radio
housing assembly and secure the
unit(s) to the assembly using the
screws supplied with the unit(s).
(Figure C)
3
Snap the double DIN trim plate onto
the front of the radio housing.
(Figure C)
4
Contin e to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C

99-5816 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire en s back 1/2"
B) Twist en s together
C) Sol er
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
e-connect the negative battery terminal and test the unit for proper operation.
eassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring onne tions using the EIA olor ode hart shown below and the instru tions in luded with the
head unit. Metra re ommends making onne tions as shown below; Strip, Spli e, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent ele tri al short ir uit.
METRA / EIA WIRING CODE
12V Ignition / A . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Bla k*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Bla k / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Bla k
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Bla k
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Bla k
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Bla k
*NOTE: When a Bla k wire is not present, ground radio to vehi le hassis.
All olors may not be present on all leads due to manufa turer’s spe ifi ations.
7

NOTES
8
99-5816