Metra Electronics 107-KI2HG User manual

Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/15/22 INST107-KI2HG
INSTALLATION INSTRUCTIONS
107-KI2HG
Patent Pending
Attention! With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
KIT FEATURES
• Designed specifically for Pioneer modular 6.8” radios like the
DMH-C2550NEX and DMH-C2500NEX. †
† Refer to the radio manufacturer for current models
• Both textured and painted gloss black to match the factory finish.
KIT COMPONENTS
• A) Front panel • B) Back panel • C) Radio chassis brackets • D) Radio display brackets • E) Display trim panel • F) #8 x 3/8” Phillips screws (4)
• G) #4 x 3/8” Phillips screws (10) • H) Panel clips (4)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..............................................2-4
Kit Preparation .......................................................5
Kit Assembly ...................................................... 6-7
A CB D E
H
Kia K5 2021-Up
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Visit metraonline.com for audio/
video and steering wheel control interface options.
Antenna Adapter: Not required
F G

386.257.1187
|
MetraOnline.com
2
1. Unclip and remove the trim panel from
the passenger side of the dash.
(Figure A)
2. Remove (2) Phillips screws exposed
after removing side panel in step 1.
(Figure B)
DASH DISASSEMBLY
3. Unclip the trim panel above the glove
box and let hang. Note: You do not need
to remove the entire panel.
(Figure C)
4. Remove (3) Phillips screws exposed
after unclipping panel above glove box
in step 3. (Figure C)
5. For models equipped with key cylinder
start on steering column:
Unclip the right side of the trim panel to
the right of the steering column below
the instrument cluster. Note: You do not
need to remove the entire trim panel.
(Figure D)
Continued on the next page
(Figure A) (Figure C)
(Figure B) (Figure D)

REV. 2/15/2022 INST107-KI2HG 3
DASH DISASSEMBLY (CONT.)
(Figure E) (Figure F)
6. Unclip and remove the trim panel below
the radio. (Figure E)
7. Unclip and remove the small trim panel
behind the radio screen then remove the
(2) Phillips screws exposed. (Figure F, G)
Continued on the next page
(Figure G)

386.257.1187
|
MetraOnline.com
4
(Figure H) (Figure I)
DASH DISASSEMBLY (CONT.)
8. Remove (2) Phillips screws below the
radio screen. (Figure H)
9. Unclip and remove the radio screen and
chassis. (Figure I)
Continue to Kit Preparation

REV. 2/15/2022 INST107-KI2HG 5
1. Secure the (4) included panel clips to the
back panel. (Figure A)
Continue to Kit Assembly
KIT PREPARATION
(Figure A)

386.257.1187
|
MetraOnline.com
6
KIT ASSEMBLY
(Figure A) (Figure D)
(Figure B) (Figure E)
(Figure C)
Pioneer Modular DDIN radio provision
Note: Reference the installation manual
provided with the radio for which hardware
to use. The display screen and radio chassis
use two different types of screws.
1. Secure the radio chassis brackets to the
back panel using (4) #8 x 3/8” screws
supplied. (Figure A)
2. Secure the radio chassis to the radio
chassis brackets using screws supplied
with the radio. Route the display
cable to the inside of the panel to be
connected next. (Figure B)
3. Remove the alignment tabs on the
radio display brackets marked 8. Secure
the radio display to the radio display
brackets using (6) screws supplied with
the radio. Note: The proper mounting
holes to use are indicated in figure D.
(Figure C, D, E)
Continued on the next page
Remove shaded tabs
Use shaded holes to mount 7” display

REV. 2/15/2022 INST107-KI2HG 7
4. Connect the cable to the radio display,
place the display trim panel over the
display, and secure to the back panel
with (4) #4 x 3/8” screws provided.
(Figure G)
5. Secure the front panel to the radio/
back panel assembly using (6) #4 x 3/8”
screws provided. (Figure H)
6. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
7. Clip the radio assembly into to the dash,
then secure using the factory screws.
8. Reassemble the dash in reverse
order of disassembly to complete the
installation.
KIT ASSEMBLY (CONT.)
(Figure H)(Figure G)

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 2/15/22 INST107-KI2HG
INSTALLATION INSTRUCTIONS
107-KI2HG
Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
[e-mail]
Tech Support Hours (Eastern Standard Time)
Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM