Metra Electronics 95-9012 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-9012
95-9012
KIT FEATURES
•Double DIN Head Unit Provision
•Stacked ISO DIN Head Unit Provision
A) Radio Housing • B) (8) Phillips screws
KIT COMPONENTS
A
•Small Flat Blade Screwdriver • Panel Removal Tool
•86-9001 Radio Removal Tools (2 sets)
1-800-221-0932
©COPYRIGHT 2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
TOOLS REQUIRED:
APPLICATIONS
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
•70-1784 VW harness 1998-2001
•XSVI-9003-NAV VW Interface 2003-up
Antenna adapter:
•40-EU55-adapter for amplified antenna 2002-up
•40-VW53 adapter for amplified antenna 1998-01
•GOLF 1999-2006
•GTI 1999-2005
•JETTA 1999-2005
(Excluding NEW JETTA 2005)
•PASSAT 2000-2005

Dash Disassembly
-Golf1999-2006..................................................1
-GTI1999-2005 ..................................................1
-JETTA 1999-2005 (Excluding NEW JETTA 2005) . . . . . . . . . . . . . . . . . . . . . . . 1
-PASSAT2000-2005 ..............................................1
Kit Assembly
-Double DIN Head Unit Provision . . . . ............ ....................2
-ISOStackedHeadUnitProvision ...................................2
Final Assembly . .................................................2
TABLE OF CONTENTS
95-9012
*Note:
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWER
Enhanceyour installation and fabrication skills
by enrolling inthe most recognized andrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 formore information
and take stepstoward abetter tomorrow.
Note: This installation kit is an extremely tight fit and requires force to be
“snapped” into the dash opening. Removal of aftermarket radio is even
moredifficult than installation, so please be sure to fully test the after-
market radio prior to completing the kit’s installation.

95-9012 DASH DISASSEMBLY
•GOLF 1999-2006 •GTI 1999-2005
•JETTA 1999-2005
(Excluding NEW JETTA 2005)
•PASSAT 2000-2005
A
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Insert the long ends of the 86-9001
into the slots on the factory radio and
pull out to remove. Note: Flat edge
of key should point outward.
(Figure A)
2
3
Continue to kit assembly.
B
For single DIN radios with the pocket,
remove the radio and pocket, then
pull out on the plastic tray separating
the dash cavity.
(Figure B)
Note: This installation kit is an extremely tight fit and requires force to be
“snapped” into the dash opening. Removal of aftermarket radio is even
more difficult than installation, so please be sure to fully test the after-
market radio prior to completing the kit’s installation.

95-9012 KIT ASSEMBLY/ FINAL ASSEMBLY
A
Locate the factory wiring harness in
the dash. Metrarecommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
batteryterminal and test the unit for
proper operation.
2
Slide the DDIN radio unit into the
DDIN bracket/radio housing assembly
and secure the unit to the kit using
the (8) Phillips screws supplied with
the kit.
(Figure A)
1
DOUBLE DIN HEAD UNIT PROVISION/
ISO STACKED HEAD UNIT PROVISION
1-800-221-0932
REV. 09-02-09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST95-9012
www.metraonline.com
Note: This installation kit is an extremely tight fit and requires force to be
“snapped” into the dash opening. Removal of aftermarket radio is even
more difficult than installation, so please be sure to fully test the after-
market radio prior to completing the kit’s installation.
Snap kit/ radio assembly into the
dash opening.
3
2