Metra Electronics 95-7330 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-7330
95-7330
KIT FEATURES
•Double DIN Radio Provision
•Stacked ISO Mount Mount Units Provision
A) Double DIN Trim Plate B) Double DIN Brackets
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver
1-800-221-0932
©COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
www.metraonline.com
TOOLS REQUIRED:
APPLICATIONS
KIA Spectra/Spectra 5 2007
B

Dash Disassembly
-KIASpectra/Spectra52007........................................1
Kit Assembly
-Double DIN/Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . 2
Final Assembly ..........................................3
TABLE OF CONTENTS
95-7330
*Note:
Refer also to the instructions included with the aftermarket radio.

95-7330 DASH DISASSEMBLY
KIA SPECTRA/SPECTRA 5 2007
A
B
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the trim panel sur-
rounding the radio and including the
a/c vents. (Figure A)
2
Remove (4) Phillips screws securing
the radio. Unplug and remove radio.
(Figure B)
3
Continue to kit assembly.

2
95-7330 KIT ASSEMBLY
B
A
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS PROVISION
Slide the Double DIN radio or the
stacked ISO mount units into the
bracket/trim plate assembly and
secure the radio or ISO mount units
to the assembly using the screws
supplied with the radio or ISO mount
units.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate. (Figure A)
1

95-7330 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown belowand the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) .............Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’sspecifications.

95-7330
NOTES
4

95-7330
NOTES
5

95-7330 INSTRUCTIONS
1-800-221-0932
REV. 09/11/07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST95-7330
www.metraonline.com