Metra Electronics 99-9224 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-9224
Phillips Screwdriver • T-25 Torx Driver
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
•DIN Head Unit Provision with Pocket
(A) Radio Housing
KIT COMPONENTS
TOOLS REQUIRED:
99-9224
APPLICATIONS
1999-2006 Volvo S80
A

Dash Disassembly
1999-2006 Volvo S80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2
Kit Assembly
DIN Head Unit Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TABLE OF CONTENTS
99-9224

99-9224
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unsnap gear shifter trim panel.
(Figure A)
2
Unsnap gear shifter boot to separate
it from the gear shifter trim panel
and remove trim panel.
(Figure B)
3
Remove (2) T-25 Torx head screws
from bottom of climate controls.
(Figure C)
4
Unsnap the climate controls from
bottom edge of the radio. Unplug
and remove the climate controls.
(Figure D)
5
DASH DISASSEMBLY
A
B
12
VOLT
C
12
VOLT
AUTO
ON AC OFF
64
68 72 76
80 64
68 72 76
80
D
1999-2006 VOLVO S80

99-9224
2
Remove (2) T-25 Torx head screws
from bottom of radio. Unplug and
remove the radio.
(Figure E)
6
Depress the snaps on the top and
bottom of the pocket to remove it
from the radio bracket.
(Figure F)
7
Remove (5) T-25 Torx head screws
securing the radio to the radio
bracket and slide the bracket off of
the radio.
(See Figure G)
Note: Save the radio bracket for
use with radio housing.
(Figure H)
8
DASH DISASSEMBLY
E
TOP SNAP
F
TORX
HEAD
G
H
1999-2006 VOLVO S80

3
99-9224
KIT ASSEMBLY
DIN HEAD UNIT PROVISION
A
B
C
D
NOTE:Also refer to the instructions
included with the aftermarket radio.
Using a Phillips screw driver remove
the rear support bracket from the
radio housing.
(Figure A)
1
Snap the radio housing into the radio
bracket (removed from factory radio)
and replace rear support bracket.
(Figure B)
2
Slide the DIN cage into the radio
housing and secureby bending the
metal locking tabs outward. (Figure C)
3
Slide the radio into the cage/ radio
housing assembly until it snaps into
place.
(Figure D)
4

4
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-9224
FINAL ASSEMBLY

5
NOTES
99-9224

INST999224
1-800-221-0932 www.metraonline.com
REV.03/15/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-9224