Metra Electronics 99-7606 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7606
Torx T-10 Driver • Small Flat Blade Screwdriver • Phillips Screwdriver
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION
•DIN Radio Provision with pocket
•ISO Radio Unit Provision with pocket
•Double DIN Radio Provision
•Stacked ISO Head Units Provision
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate
•F) Pocket • G) (6) Panel Clips • H ) Two Sided Tape (Not Shown)
KIT COMPONENTS
99-7606
AB
APPLICATIONS
Nissan Titan
(With Dual Zone Climate Controls) 2006-07
Nissan Pathfinder Armada 2006-07
F
E
CD
TOOLS REQUIRED:
Or Panel Removal Tool
G

TABLE OF CONTENTS
99-7606
• Dash Disassembly
-Nissan Titan 2006 -07................................................................1, 2
-Nissan Pathfinder Armada 2006-07...........................................1, 2
• Kit Assembly:
- Pre-Kit Assembly............................................................................3
-DIN Radio Provision with Pocket ...................................................4
-ISO Radio Provision with Pocket ...................................................5
-Double DIN Radio Provision ...........................................................6
-Stacked ISO Head Units Provision..................................................7
• Final Assembly ...............................................................................8

1
99-7606 DASH DISASSEMBLY
OFF
A
B
C
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove entire panel
including radio and climate controls.
(Figure A)
2
Remove (4) Phillips screws to
remove radio from sub-dash.
(Figure B)
3
Unsnap and remove the outer trim
rings around a/c control knobs.
(Figure C)
NOTE: The small round Airbag stick-
er also needs to be removed from
the factory panel and placed onto
the 99-7606 radio housing panel.
(A round piece of double-sided tape
is provided in case the factory stick-
er is not strong enough.) (Figure C)
4
Remove (4) T-10 Torx screws from
the a/c controls to remove from the
factory radio trim panel.
(Figure D)
5
NISSAN TITAN 2006-07
NISSAN PATHFINDER ARMADA2006-07
Continued on next page.

2
99-7606 DASH DISASSEMBLY
Unclip and remove the Hazard Light
switch assembly.
(Figure D)
6
Remove (2) T10 Torx screws from
the passenger air bag off light
assembly and remove.
(Figure D)
Note: The small round sticker
also needs to be removed from
the factory panel and placed
onto the 99-7606 radio housing.
7
NISSAN TITAN 2006-07
NISSAN PATHFINDER ARMADA2006-07
Continue to kit assembly.
CLIP
HAZARD SWITCH
PASSENGER AIR BAG LIGHT
T-10 TORX
SCREW
T-10 TORX
SCREW
A/C CONTROL PANEL
INSIDE VIEW - RADIO TRIM PANEL BACK
1
2
3
4
T-10 TORX SCREWS
T-10 TORX SCREWS
12
D

3
99-7606 PRE-KIT ASSEMBLY
Attach the passenger air bag off light
assembly to the 99-7606 Radio
Housing using the factoryhardware
removed in the dash disassembly.
Also, apply to air bag button the
small round airbag sticker previously
removed in Step 4 dash disassembly.
(FigureC)
3
Attach the a/c control to the 99-7606
Radio Housing using the factory
hardware removed in the dash dis-
assembly. (Figure A)
1
Snap the outer trim rings onto the
a/c control knobs. (Figure B)
2
Snap the hazard light switch into the
99-7606 Radio Housing.(FigureD)
4
Attach the (6) panel clips to the 99-
7606 radio housing panel using the
factory radio panel as a reference for
clip positioning.
5
NISSAN TITAN 2006-07
NISSAN PATHFINDER ARMADA2006-07
A/C
123
4
0
1
2
3
4
0
MAX
A/C
R
R
R
A
A/C
123
4
0
1
2
3
4
0
MAX
A/C
R
R
R
B
A/C
OFF
123
4
0
1
2
3
4
0
MAX
A/C
R
R
R
C
A/C
OFF
123
4
0
1
2
3
4
0
MAX
A/C
R
R
R
D
Continue to kit assembly.

4
99-7606 KIT ASSEMBLY
Snap the pocket into the radio
housing.
(Figure C)
3
Slide the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
(Figure A)
1
Slide the aftermarket radio unit
into the cage and secure.
(Figure B)
2
DIN RADIO PROVISION WITH POCKET
Continue to final assembly.
A
B
C

5
99-7606 KIT ASSEMBLY
Snap the pocket into the radio hous-
ing.
(Figure D)
4
Slide the radio into the radio
opening until the side clips
engage. (Figure B)
2
Snap the Trim plate into the Radio
Housing.
(FigureC)
3
ISO RADIO PROVISION WITH POCKET
A
Mount the ISO Brackets to the
radio with the screws supplied
with the radio.
(Figure A)
1
B
C
D
Continue to final assembly.

6
99-7606 KIT ASSEMBLY
Slide the Double DIN radio into the
Double DIN bracket/radio housing
assembly and secure the radio to the
kit using the screws supplied with
the head unit.
(Figure C)
3
Cut and remove center divider
from radio housing.
(Figure A)
1
Snap the Double DIN trim plate
onto the housing/radio assembly.
(Figure C)
4
Snap the Double DIN brackets to
the inside edge of the radio hous-
ing.
(Figure B)
2
DOUBLE DIN RADIO UNIT PROVISION
A
B
C
Continue to final assembly.

7
99-7606 KIT ASSEMBLY
Snap the Double DIN trim-plate onto
the housing/radio assembly.
(Figure C)
4
Snap the Double DIN brackets to
the inside edge of the radio hous-
ing.
(Figure B)
2
Slide the stacked ISO units into the
Double DIN bracket/radio housing
assembly and secure the units to the
kit using the screws supplied with
the head units.
(Figure C)
3
STACKED ISO HEAD UNITS PROVISION
Cut and remove center divider
from radio housing. (Figure A)
1
A
B
C
Continue to final assembly.

8
FINAL ASSEMBLY
Make wiring connections using the EIA color code chart shown belowand the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
FINAL WIRING CONNECTIONS
99-7606
FINAL ASSEMBLY
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray/ Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
METRA / EIA WIRING CODE
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D