Metra Electronics 95-7419 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-7419
Phillips Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION
•Double DIN Head Unit Provision
•Stacked ISO DIN Head Unit Provision
• ( A) DDIN Trim plate
KIT COMPONENTS
TOOLS REQUIRED:
95-7419
A
APPLICATIONS
Nissan Altima
2005-2006
(Without factory navigation)

Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TABLE OF CONTENTS
95-7419

95-7419
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove the trim panel
surrounding the climate controls.
(Figure A)
2
2005-06 NISSAN ALTIMA
Remove (4) Phillips screws securing
climate control and remove.
(Figure B)
3
Unclip and remove the panel sur-
rounding radio including A/C vents.
(Figure C)
4
Remove (4) Phillips screws securing
radio to remove. (Figure D)
5
DASH DISASSEMBLY
SCAN
AUDIO CLOCK
CAT-RPT
123
456
75
A
SCAN
AUDIO CLOCK
CAT-RPT
123
456
75
AUTO
A/C
AUTO
OFF
HI
90
60
B
C
D

2
95-7419
2005-06 NISSAN ALTIMA
KIT ASSEMBLY
Snap the 95-7419 trim plate into the
radio trim panel. (Figure A)
1
Slide the DDIN radio unit into the
factory brackets and secure the unit
to the brackets using the screws
supplied with the head unit.
(Figure B)
2
DOUBLE DIN HEAD UNIT PROVISION
Install the 95-7419 Trim Plate
from Rear
A
B

95-7419
KIT ASSEMBLY
2005-06 NISSAN ALTIMA
Snap the 95-7419 trim plate into the
radio trim panel. (Figure A)
1
Slide the stacked ISO DIN units into
the factory brackets and secure the
units to the brackets using the
screws supplied with the head units.
(Figure B)
2
STACKED ISO DIN HEAD UNIT PROVISION
Install the 95-7419 Trim Plate
from Rear
A
B
3

4
95-7419
FINAL ASSEMBLY
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative batteryterminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown belowand the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS

5
NOTES
95-7419

95-7419
1-800-221-0932 www.metraonline.com
REV 03-03-08 © COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION INST95-7419