Metra Electronics 99-7610B User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7610
99-7610B
99-7610HG
2007-up
Nissan Versa
2011 Nissan Juke
KI FEA URES
• DIN head unit provisions with pocket
• ISO DIN head unit provision with pocket
• Double DIN mount radio provision
• B = Matte Black
• HG = Gloss Black
• 70-7552 - 2007-up Nissan Harness
• 40-NI12 - 2007-up Nissan Antenna Adapter
KI COMPONEN S
WIRING AND AN ENNA CONNEC IONS
(Sold Separately)
A
OOLS REQUIRED:
Panel Removal ool • Phillips Screwdriver
Socket Wrench
1-800-221-0932
© COPYRIGHT 2011 METRA ELECTRONICS CORPORATION
me raonline.com
B
D
C
A) Radio Housing • B) ISO Brackets • C) rim Plate • D) DDIN rim Plate
METRA. THE WORLD’S BEST KITS.™
APPLICA IONS
INSTALLATION INSTRUCTIONS FOR PART 99-7610

Dash Disassembly
- Nissan ersa 2007-up..............................................................................1
- Nissan Juke 2011....................................................................................2
Kit Assembly
- DIN Mount Radio Provision with Pocket .................................................. 3
- ISO Mount Radio Provision with Pocket ............................................... 4-5
- Double DIN Mount Radio Provision ..........................................................6
TABLE OF CONTENTS
Cauti n
Metra rec mmends disc nnecting the negative battery terminal bef re beginning
any installati n. All access ries, switches, and especially air bag indicat r lights
must be plugged in bef re rec nnecting the battery r cycling the igniti n.
N te: Refer als t the instructi ns included with the aftermarket radi .
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Met a ecommends MECP
ce tified technicians
INSTALLATION INSTRUCTIONS FOR PART 99-7610

VOL
CD
LOAD
SCRL
AUDIO
SCAN
CAT CH
AUX
6CD CHANGER
RPT
RDM
DISP CLOCK
RADIO
PRESET A-B-C
SEEK
TRACK
FILE
TUNE
FF-REW
FOLDER
PWR
PUSH
1
2
3
4
5
6
1
1. Unclip and remove the panel above
the radio. (Figure A, B)
2. Remove (2) Phillips screws securing
the radio trim panel then unclip and
remove the entire panel surrounding
the radio and a/c controls. (Figure C)
3. Remove (4) Phillips screws securing
radio, unplug and remove radio.
(Figure D)
Continue to kit assembly.
Figure A
Figure B
Figure C
Figure D
99-7610 DASH DISASSEMBL
2007-UP NISSAN VERSA

2
1. Unclip and remove the climate control
panel. (Figure A)
2. Remove (2) Phillips screws securing
the radio trim panel. (Figure B)
3. Remove (4) Phillips screws securing
radio, unplug and remove radio.
(Figure C)
Continue to kit assembly.
99-7610 DASH DISASSEMBL
2011 NISSAN JUKE
Figure A
Figure B
Figure C

3
N te: Y u will need t rem ve the after-
market radi ’s trim ring if equipped.
1. Cut and remove the appropriate tabs
not necessary for your application.
(Figure A)
2. Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure B)
3. Slide the aftermarket head unit into
the cage and secure. (Figure C)
4. Locate the factory wiring harness and
antenna plug in the dash. Metra
recommends using the proper mating
adapters from Metra and/or AXXESS.
5. Attach the trim plate supplied with
the kit to the front of the radio
housing assembly. (Figure C)
6. Reassemble dash in reverse order
of disassembly.
Nissan Versa
Nissan Juke
Nissan Juke
99-7610
Figure A
Figure C
Figure B
DIN HEAD UNIT PROVISION

FRONT
FACE-
RIGHT
SIDE
BRACKET
N te: The f ll wing m dificati n will
need t be made t b th ISO brackets
when using the ISO m unt radi
pr visi n. Cut r trim the area sh wn
fr m the ISO bracket. (Figure A)
1. Cut and remove the appropriate tabs
not necessary for your application.
(Figure B)
Continued on page 5.
Figure A
99-7610
4
ISO MOUNT RADIO PROVISION
Nissan Versa
Nissan Juke
Nissan Juke
Figure B

1. Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure C)
2. Slide the head unit into the radio
opening until the side clips engage.
(Figure D)
3. Locate the factory wiring harness and
antenna plug in the dash. Metra
recommends using the proper mating
adapters from Metra and/or AXXESS.
4. Attach the trim plate supplied with
the kit to the front of the radio
housing assembly. (Figure D)
5. Reassemble dash in reverse order
of disassembly.
Figure C
Figure D
99-7610
5

1. Mount the factory brackets
(removed from factory radio during
disassembly) to the sides of the
double DIN radio using screws
supplied with the double DIN radio.
(Figure A)
2. Locate the factory wiring harness and
antenna plug in the dash. Metra
recommends using the proper mating
adapters from Metra and/or AXXESS.
3. Place the DDIN trim plate on the front
of the DDIN radio. (Figure B)
4. Reassemble dash in reverse order
of disassembly.
Figure A
Figure B
99-7610
6
DOUBLE DIN MOUNT RADIO PROVISION

99-7610
NOTES

NOTES
99-7610