Metra Electronics 99-8903B User manual

INSTALLATION INSTR CTIONS FOR PART 99-8903B
APPLICATIONS
S BAR
LEGACY & O TBACK
2010-11
(FOR NON-NAVIGATION RADIOS ONLY)
KIT FEATURES
• DIN ra io provision with pocket
• ISO ra io provision with pocket
• Painte scratch resistant matte black
A) Ra io Housing B) ISO Brackets C) Trim plate
KIT COMPONENTS
A
TOOLS REQUIRED:
• Small Flat Bla e Screw river • Phillips Screw river
• Panel Removal Tool • Socket Wrench
1-800-221-0932
© COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION
www.me raonline.com
99-8903B
BC
METRA. THE WORLD’S BEST KITS.™
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wirin Harness:
• 70-8901 Subaru Harness 1990-Up
• 70-7552 Nissan Harness 2007-Up
Antenna Adapter:
• 40-SB10 Subaru Antenna Adapter 2005-Up

Da h Di a embly
- 2010-11 Subaru Legacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
- 2010-11 Subaru Outback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit A embly
- DIN Head Unit Provi ion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
- ISO DIN Head Unit Provi ion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TABLE OF CONTENTS
99-8903B
*Note:
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP certified
technicians.

99-8903B DASH DISASSEMBLY
2010-11 S BAR LEGACY / O TBACK
A
1
Disconnect the negative battery ter-
minal to prevent an acci ental short
circuit.
1
Unclip an remove the ra io trim panel
inclu ing the a/c vents. ( Figure A)
2
Remove (4) Phillips screws securing
the factory ra io.
3

99-8903B KIT ASSEMBLY
A
B
2
Locate the factory wiring harness in
the ash. Metra recommen s using
the proper mating a apter from Metra
or AXXESS. Re-connect the negative
battery terminal an test the unit for
proper operation.
1
Sli e the DIN cage into the Ra io
Housing an secure by ben ing the
metal locking tabs own. (Figure A)
2
Sli e the aftermarket hea unit into
the cage an secure. (Figure B)
3
Reassemble ash in reverse or er of
isassembly.
4
2010-11 S BAR LEGACY / O TBACK
DIN HEAD NIT PROVISION

99-8903B KIT ASSEMBLY
A
B
3
Locate the factory wiring harness in
the ash. Metra recommen s using
the proper mating a apter from Metra
or AXXESS. Re-connect the negative
battery terminal an test the unit for
proper operation.
1
Mount the ISO Brackets to the hea
unit with the screws supplie with
the unit. (Figure A)
2
Sli e the hea unit into the ra io
opening until the si e clips engage.
(Figure B)
3
Snap the Trim plate into the Ra io
Housing. (Figure B)
4
Reassemble ash in reverse or er of
isassembly.
5
2010-11 S BAR LEGACY / O TBACK
ISO DIN HEAD NIT PROVISION

NOTES
99-8903B

NOTES
99-8903B

306
INSTR CTIONS
1-800-221-0932
REV. 11/18/10 © COPYRIGHT 2003-2010 METRA ELECTRONICS CORPORATION INST99-8903B
www.me raonline.com
99-8903B INSTR CTIONS
METRA. THE WORLD’S BEST KITS.™