Metra Electronics 99-5816 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-5816
99-5816
APPLICATIONS
FORD Focus
2008-2009
KIT FEATURES
•DIN Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
•Stacked ISO Mount Units Provision
• Painted To Match Factory Dash
•A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Pocket • G) (2) Top Clips and (4) Middle Radio Housing Clips
KIT COMPONENTS
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set • Cutting Tool
1-800-221-0932
©COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
D
E
C
F
(2) TOP CLIPS (4) MIDDLE CLIPS
SIDE VIEW SIDE VIEW
G

Dash Disassembly
- FordFocus2008-2009. ........................... .. 1,2
Kit Assembly
-Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
-DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4
-ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5
-Double DIN /Stacked ISO Mount Units Radio Provision . . . . . . . . . . . . .6
Final Assembly ...........................................7
TABLE OF CONTENTS
99-5816
Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.

1
4
5
FORD FOCUS 2008-2009
95-5816 DASH DISASSEMBLY
Disconnect the negative battery termi-
nal to prevent an accidental short cir-
cuit.
1
Unclip and remove the trim panel sur-
rounding the shifter and including the
cup holders. (Figure A)
Remove (2) 9/32” screws facing up
above the gauge cluster then unclip
and remove the trim panel surrounding
the gauge cluster.
(Figure C)
Unclip and remove the trim panel
above the glove box. (Figure D)
Continue on page 2.
2
Remove (2) 9/32” screws from the bot-
tom edge of the factory radio trim
panel. (Figure B)
3
PA S S
AIRBAG
OFF
PAS S
AIRBAG
OFF
C
PAS S
AIRBAG
OFF
D
B
A

2
95-5816 DASH DISASSEMBLY
Continue to kit preparation.
Unclip and remove the vent panel at
the top of the factory radio trim panel.
(Figure E)
6
Remove (4) T-20 Torx screws securing
the climate controls to the factory
radio trim panel assembly and
remove the controls from the assem-
bly. (Retain the screws and climate
controls for re-use during kit prepara-
tion.) (Figure G)
9
Remove (4) T-20 Torx screws securing
the accessorysocket panel to the
factory radio trim panel assembly and
remove the socket panel from the
assembly. (Retain the screws and
accessorysocket panel for re-use
during kit preparation.)
(Figure G)
10
Unclip and remove the passenger air
bag light and the switchpanel blank
plates. (Retain the air bag light and
blank plates for re-use during kit
preparation.)
(Figure G)
11
Unclip the factory radio trim panel
assembly. Unplug and remove the
assembly. Note: Some early models
had a ground strap attached to the
radio chassis and the sub dash with
an 8 MM bolt. You will need to unbolt
this strap to remove the factory radio
trim panel assembly.
8
Remove (2) 9/32” screws behind the
vent panel removed in step 6.
(Figure F)
7
FORD FOCUS 2008-2009
12345
7890
6
PA S S
AIRBAG
OFF
G
F
E

3
99-5816 KIT ASSEMBLY
KIT PREPARATION
1
Secure the climate control into the
radio housing using the factory hard-
ware. ( Figure A)
2
Secure the accessory socket panel to
the radio housing using the factory
hardware. (
Figure B)
3
Clip the passenger air bag light and
the switch panel blank plates in to
the radio housing. ( Figure C)
4
Attach Top and Middle Radio Housing
Clips to the backof the radio housing.
(
Figure D,E)
NOTE: When the clips are properly
attached they should be on a 90
degree angle with the radio housing.
( Figure E)
Continue to kit assembly.
C
(4) MIDDLE CLIPS
SIDE VIEW
(2) TOP CLIPS
SIDE VIEW FRONT VIEW FRONT VIEW
D
E
B
A

99-5816 KIT ASSEMBLY
4
A
B
C
DIN MOUNT RADIO PROVISION WITH POCKET
Slide the DIN cage into the radio hous-
ing and secureby bending the metal
locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the DIN
cage and until it snaps into place.
(Figure B)
2
Snap the pocket into the radio housing.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-5816 KIT ASSEMBLY
5
A
B
C
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
1
Slide the radio into the radio housing
until it snaps into place. (Figure B)
2
Snap the trim plate onto the front of
the Radio Housing. (Figure B)
3
Snap the Pocket into the radio
housing. (Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-5816 KIT ASSEMBLY
6
DOUBLE DIN/STACKED ISO MOUNT
UNITS RADIO PROVISION
Cut and remove the center bar from
the radio housing. (Figure A)
1
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the Double DIN or stacked ISO
mount unit(s) into the bracket/radio
housing assembly and secure the
unit(s) to the assembly using the
screws supplied with the unit(s).
(Figure C)
3
Snap the double DIN trim plate onto
the front of the radio housing.
(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C

99-5816 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown belowand the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground..............Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer.................Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) .............Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) ..............Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7

NOTES
8
99-5816