Metra Electronics MAZDA 6 2009 99-7511S User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7511S
99-7511S
APPLICATIONS
Mazda 6 2009
KIT FEATURES
•DIN Radio Provision
•ISO Mount Radio Provision
• Double DIN Radio Provision
•Stacked ISO Mount Radio Provision
• Painted To Match Silver Factory Dash
•A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Pocket • G) Filler Trim Panel • H) (2) #3 3/8” Phillips Screws
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set
1-800-221-0932
©COPYRIGHT 2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
DEG
C
TOOLS REQUIRED:
F
H

Dash Disassembly
- Mazda62009 ................................ . . . . . . 1
Kit Assembly
-DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
-ISO Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
-Double DIN /Stacked ISO Mount Unit(s) Provision . . . . . . . . . . . . . . . . 4
Final Assembly ...........................................5
TABLE OF CONTENTS
99-7511S
*Note:
Refer also to the instructions included with the aftermarket radio.

99-7511S DASH DISASSEMBLY
MAZDA62009
A
B
C
D
1
1
Unclip and remove the trim panel
above the glove box and down the
right side of the center console.
(
Figure B)
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
3
Unclip and remove the cup
holder/parking brake trim panel.
( Figure A)
2
Unclip and remove the trim panel next
to the key switch and down the left
side of the center console. ( Figure B)
4
Unclip and remove the trim panel
surrounding the climate controls and
the shifter lever. (
Figure C)
5
Unclip and remove the vent panel
above the radio. ( Figure D)
6
Remove (4) screws securing the
factory radio. Unplug and remove the
radio.
7
Continue to kit preparation

99-7511S KIT ASSEMBLY
2
REAR OF RADIO HOUSING
FILLER TRIM PANEL
A
B
C
D
DIN RADIO PROVISION
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure B)
2
Attach the filler trim panel to the back
of the radio housing at the bottom
edge. (Figure A)
1
Slide the aftermarket radio into the DIN
cage until it snaps into place. (Figure C)
3
Snap the pocket into the the bottom
opening of the radio housing.
(Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7511S KIT ASSEMBLY
3
B
A
REAR OF RADIO HOUSING
FILLER TRIM PANEL
C
D
ISO MOUNT RADIO PROVISION
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure B)
2
Slide the radio into the radio housing
until it snaps into place. (Figure C)
3
Snap the Trim Plate onto the front of
the Radio Housing.
(Figure C)
4
Snap the pocket into the bottom open-
ing of the radio housing. (Figure D)
5
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Attach the filler trim panel to the back
of the radio housing at the bottom
edge. (Figure A)
1

99-7511S KIT ASSEMBLY
4
DOUBLE DIN/STACKED ISO MOUNT
UNIT(S) PROVISION
Cut and remove the center bar from
the Radio Housing. (Figure B)
2
Snap the Double DIN brackets to the
inside edge of the Radio Housing.
(Figure C)
3
Slide the Double DIN or stacked ISO
mount unit(s) into the bracket/radio
housing assembly and secure to the
assembly using the screws supplied
with the unit(s). Snap the DDIN Trim
Plate onto the front of the Radio
Housing.
(Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
REAR OF RADIO HOUSING
FILLER TRIM PANEL
B
C
D
Attach the filler trim panel to the back
of the radio housing at the bottom
edge. (Figure A)
1

99-7511S FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground..............Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) .............Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
Enjoy your newly installed radio!
5

99-7511S INSTRUCTIONS
1-800-221-0932
Rev. 01/13/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION NST99-7511S
www.metraonline.com