Metra Electronics 99-3010S User manual

metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION METRA. The World’s best kits.™1-800-221-0932
APPLICATIONS
INSTALLATION INSTRUCTIONS FOR PART 99-3010S
REV. 10/23/2013 INST99-3010S
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
• DINheadunitprovisionwithpocket
• ISODINheadunitprovisionwithpocket
• DoubleDINheadunitprovision
• StackedISODINheadunitprovision
• Painted Silver to match factory finish
•A)Radiotrimpanel•B)Radiohousing•C)ISObrackets•D)ISOtrimplate•E)DoubleDINbrackets
•F)DDINtrimplate•G)Pocket•H)Interface•I)20-pinGMharness•J)4-pinto4-pinresistorpadharness
•K)22-pinto44-pinCamaroharness•L)18-pinto10-pinHVACharness
KIT FEATURES
KIT COMPONENTS
Chevrolet Camaro 2010-up
99-3010S
WIRING & ANTENNA CONNECTIONS(soldseparately)
WiringHarness:
•Interfaceincluded
AntennaAdapter:
•40-EU55-Amplifiedantennaadapter
•Panelremovaltool•Phillipsscrewdriver
•Socketwrench
TOOLS REQUIRED
A B C D E F G
LKJIH

99-3010S99-3010S
2
Table of Contents
Dash Disassembly
–ChevroletCamaro2010-up.............................................................................. 2-3
Kit Preparation......................................................................................................3
Kit Assembly
–DINheadunitprovisionwithpocket.....................................................................4
–ISO DINheadunitprovisionwithpocket...............................................................4
–DoubleDIN/StackedISODINheadunitprovision..................................................5
Axxess Interface Installation........................................................................... 5-6
–InstallingInterface...............................................................................................7
–VehicleCustomizationwithOptionalLCD.............................................................7
–ChangingDisplayBacklightColor.................................................................. (back)
1. Unclipandremovethe(2)sidetrim
panelsrunningthelengthofthe
centerconsole.(FigureA)
2. Remove(1)9/32”screwfrom
eachsideofthefrontofthecenter
console.(FigureB)
3. Remove(2)9/32”screwsperside
fromthecoveronthebackofthe
centerconsolethenunclipand
removethecover.(FigureC)
Dash Disassembly
0
30
70 9
12
19
180
200
320
300
30
100
0
30
70 9
12
19
180
200
320
300
30
100
(Figure A)
(Figure B)
0
30
70 9
12
19
180
200
320
300
30
100
(Figure C)

99-3010S99-3010S
3
4. Remove(2)9/32”screwsexposed
underthecoveronthebackof
console.(FigureD)
5. Liftupontherearoftheconsole
andslidetowardthebackofthe
vehiclethenunclipandremovethe
entirecenterconsole.(FigureE)
6. Remove(2)9/32”screwssecuring
theclimatecontrol/radiotrimpanel
andremove.(FigureF)
7. Remove(4)Phillipsscrews
securingtheradiochassis.
(FigureG)
Continue to kit preparation
1. Cutandremovethesubdash
radiosupporttomakeroomforthe
interfaceandharnesses.(FigureA)
2. Removepanelclipsfromfactory
radioandattachtothetopofthe
kithousing.(FigureB)
Continue to kit assembly
Kit Preparation
(Figure F)
(Figure G)
(Figure E)
Dash Disassembly
(Figure D)
(Figure B)
(Figure A)

99-3010S99-3010S
4
DIN head unit provision with pocket
1. SlidetheDINcageintotheradio
housingandsecurebybending
themetallockingtabsdown.
(FigureA)
2. Snapthepocketintothebottom
openingoftheradiohousing.
(FigureB)
3. Slidetheaftermarketheadunitinto
thecageandsecure.(FigureB)
4. Reassembledashinreverseorder
ofdisassemblyusingthe99-3010S
radiotrimpanelinsteadofthe
factorypanel.
5. Programming:Youmustcyclethe
A/Cfanspeedallthewaytohigh
andbacktolowwhenyoufirst
installthekit.
ISO DIN head unit provision with pocket
1. MounttheISObracketstothehead
unitwiththescrewssuppliedwith
theunit.(FigureA)
2. Snapthepocketintothebottom
openingoftheradiohousing.
(FigureB)
3. Slidetheheadunitintotheradio
openinguntilthesideclipsengage.
(FigureB)
4. Snapthetrimplateintothe
radiohousing.(FigureC)
5. Reassembledashinreverseorder
ofdisassemblyusingthe99-3010S
radiotrimpanelinsteadofthe
factorypanel.
6. Programming:Youmustcyclethe
A/Cfanspeedallthewaytohigh
andbacktolowwhenyoufirst
installthekit.
(Figure A)
(Figure B)
(Figure A)
Kit Assembly
(Figure C)
(Figure B)

99-3010S99-3010S
5
Double DIN/Stacked ISO DIN
head unit provision
1. Cutandremovethecentersupport
(ForDDINonly).(FigureA)
2. SnaptheDoubleDINbracketsto
theinsideedgeoftheDoubleDIN
radiohousing.(FigureB)
3. SlidetheDoubleDINheadunitor
stackedISOheadunitsintothe
bracket/radiohousingassembly
andsecuretheDoubleDINhead
unitorstackedISOheadunitsto
theassemblyusingthescrews
suppliedwiththeradio.(FigureC)
4. SnapthedoubleDINtrimplateinto
theDDINradiohousing.(FigureC)
5. Reassembledashinreverse
orderofdisassemblyusingthe
99-3010Sradiotrimpanelinstead
ofthefactorypanel.
6. Programming:Youmustcyclethe
A/Cfanspeedallthewaytohigh
andbacktolowwhenyoufirst
installthekit.
(Figure B)
(Figure C)
(Figure A)
Kit Assembly Axxess Interface
Installation
•Cuttingtool•Crimpingtool•Tape•Connectors(butt-connectors,bellcaps,etc.)
TOOLS REQUIRED
•4-pinto4-pinresistorpadharness•16-pinwithstrippedleads•22-pinto44-pin
CamaroHarness•18-pinto10-pinHVACHarness
INTERFACE COMPONENTS
FEATURES
• Providesaccessory(12-volt10-amp)
• RetainsR.A.P.(RetainedAccessoryPower)
• Usedinamplifiedornon-amplifiedsystems
• Retainsallwarningchimes
• ProvidesNAVoutputs(parkingbrake,reverse,mute,andV.S.S.)
• RetainsOnStar/OEBluetooth
• AdjustablevolumeforchimesandOnStar
• Highlevelspeakerinput
• Micro“B”USBupdatable
• Retainsbalanceandfade

99-3010S99-3010S
6
Axxess Interface
Installation
From the 16-pin harness:
• ConnecttheRedwirestothe
ignition/accessorywireofthe
aftermarketradio.
• ConnecttheOrange/Whitewiretothe
illuminationwireoftheaftermarket
radio.Iftheaftermarketradiohasno
illuminationwire,tapeofftheOrange/
Whitewire.
• ConnecttheBlue/Whitewire
totheampturnonwireofthe
aftermarketradio(Note,wiremustbe
connectedevenifthereisn’tanAMP
inthevehicle).
• ConnecttheBrownwiretothemute
wireoftheaftermarketradio.Ifthe
aftermarketradiodoesnothave
aMutewire,tapeuptheBrown
wire(Note,iftheMutewireisnot
connectedtheradiowillturnoffwhen
OnStarisactive).
• ConnecttheWhitewiretotheleft
frontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretothe
leftfrontnegativespeakeroutputof
theaftermarketradio.
• ConnecttheGraywiretotheright
frontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Blackwiretothe
rightfrontnegativespeakeroutputof
theaftermarketradio.
• TheVioletwireisnotusedin
theapplication.
• TheViolet/Blackwireisnotusedin
theapplication.
• TheGreenwireisnotused
intheapplication.
• TheGreen/Blackwireisnotusedin
thisapplication.
Thefollowingwiresareforthe
aftermarketradiosthathave
navigationbuiltin:
• ConnecttheLight Greenwiretothe
parkingbrakewireoftheaftermarket
navigationradio.
• ConnecttheBlue/PinkwiretotheVSS
orspeedsensewireoftheaftermarket
navigationradio.
• ConnecttheGreen/Purplewireto
thereversewireoftheaftermarket
navigationradio.
From the 44-way harness:
• ConnecttheBlackwiretotheground
wireoftheaftermarketradio.
• ConnecttheYellowwiretothe12-volt
constantwireoftheaftermarketradio.
• ConnectthePinkwiretotheother
Pinkwirelocatedonthe18-pinto
10-pinHVACharness(ignorewriting
onwire--thisisNOTa“mute”wire).
• ConnecttheRCA’stotheAUXinonthe
aftermarketradio(ifequipped).
Note:•Thiswillallowyoutoretainthe
3.5AUXjackintheconsole.
•The3.5AUXjackcanonlybe
used if it is a single AUX jack.
•IftheAUXjackhasaUSBport
neithercanbeused.
For amplified vehicles:
• ConnecttheVioletwiretothe
rightrearpositivewireofthe
aftermarketradio.
• ConnecttheViolet/Blackwireto
therightrearnegativewireofthe
aftermarketradio.
• ConnecttheGreenwiretotheleftrear
positivewireoftheaftermarketradio.
• ConnecttheGreen/Blackwireto
theleftrearnegativewireofthe
aftermarketradio.
For non-amplified vehicles:
• CuttheresistorsfromtheGreen,
Green/black, Purple, Purple/Black
rightbelowtheheatshrink.
• ConnecttheVioletwireto
therightrearpositivewireofthe
aftermarketradio.
• ConnecttheViolet/Blackwireto
therightrearnegativewireofthe
aftermarketradio.
• ConnecttheGreenwiretotheleftrear
positivewireoftheaftermarketradio.

99-3010S99-3010S
7
• ConnecttheGreen/Blackwireto
theleftrearnegativewireofthe
aftermarketradio.
Additional 12-pin harness (ASWC-1):
• This12-pinharnessistobeusedin
conjunctionwiththeASWC-1
(notincluded).Pleaserefertothe
ASWC-1instructionsforprogramming.
Installing the
Interface
1. Withalltheconnectionscompleted,
plugthe16and22-pinharnessesinto
theinterface.
2.Plugthe44-pinGMharnessintothe
vehiclesideharness,andplugthe
aftermarketradioharnessintothe
aftermarketradio.
3. Reconnectthenegative
batteryterminal.
Testing the Interface
Withthevehiclebatteryre-connected,
cyclethekeyonfora30seconds,then
offandbackon.Turntheignitionon,
andthenturntheaftermarketradioon.
PushtheOnStarbutton,theradioshould
turnoff(radiowillmuteifmutewireis
connected)andyoushouldhearOnStar.
PushtheOnStarcancelbuttonandthe
radioshouldcomebackon.Cyclethe
A/Cfanspeedallthewaytohighand
backtolowwhenyoufirstinstallthekit.
Chime Volume Adjustment
1) Withcaron,shutoffcar
andleavekeysinignition.Openthe
cardoorandleaveitopen.Chimes
willbeheard.
2) Wait10seconds,thenwithasmall
screwdriveradjustthepotentiometer
fullycounterclockwise(alltheway
left),thenclockwisetoraisechime
levelandcounterclockwisetolower
thechimelevel.
3) Whenthevolumeisatthedesired
level,removethekeysfromthe
ignition.Thiswilllockthechime
volumeatitscurrentlevel.
Audio Level Adjustment
1) Startyourvehicleandturnonthe
radiohavingaudioplaying.
2) Turnyouraftermarketradio’svolume
up¾oftheway.
3) Withasmallscrewdriveradjustthe
potentiometerclockwisetoraisethe
audiolevelandcounterclockwiseto
lowertheaudiolevel.
4) Onceatdesiredlevelyouraudio
adjustmentiscomplete.
OnStar Level Adjustment
ToadjusttheOnStartap“volumeup”or
“volumedown”onthesteeringwheel.If
steeringwheelcontrolsarenotpresent
findtheBlack/Yellowwireonthe
16-pinharness.PushtheblueOnStar
button,whilethevoiceisspeaking,tap
theBlack/Yellowwiretoground.Once
volumeissetitwillstayatthatvolume
untiltheBlack/Yellowwireistapped
togroundagain.Thiscanbesetduring
installationandthenleftalone.
Vehicle customization
with optional LCD
(AXXESSpart#XIA-LCDsoldseparately)
The OEM radio is used to customize
certain features of the vehicle.
UsetheoptionalLCDtoadjustthese
featuresaccordingly:
1. Pressthe“ESC”buttonand“Press
EntertoSetLanguage”willappear
onthescreen.
2. Tochangethe“Language”pressthe
“Enter”buttonthenpressthenpress
the“Up”and“Down”buttonsto
changethe“Language”.
3. Onceyouhavechosenyou
“Language”thenpress“ESC”togo
backtobeabletoscrollthroughthe
othersettings.
4. Ifyoudonotwishtochangethe
“Language”youcanscrollupand
downthroughthedifferentsettings
withthe“Up”and“Down”buttons.
5. Remembertopress“Enter”to
changethedesiredsetting.

metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION METRA. The World’s best kits.™1-800-221-0932
INSTALLATION INSTRUCTIONS FOR PART 99-3010S
REV. 10/23/2013 INST99-3010S
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Red
Color Level Up
ColorLevelDown
Green Blue
Pressandholdtoenter
“ConfigureBacklightColor”mode
(Figure A)
Changing Display
Backlight Color
1. Pressthefrontdefrostbuttonfor5seconds,
thiswillengagethe“ConfigureBacklight
Color”mode.Note,backlightwillblinkwhile
inthismode.(FigureA)
2.Createyourbacklightcolor(FigureA):
• Pressandholdthe“Face”buttonto
increaseRed.
• Pressthe“Foot”buttontodecreaseRed.
• Pressandholdthe“Face/Foot”buttonto
increaseGreen.
• Pressandholdthe“Def/Foot”buttonto
decreaseGreen.
• Pressandholdthe“FanUp”buttonto
increaseBlue.
• Pressandholdthe“FanDown”buttonto
decreaseBlue.
3. Afteryouhaveyourdesiredcolorstop
pressingthebutton(s)andtheblinkingwill
stopleavingyourdesiredcolor.(FigureA)

METRA. The World’s best kits.™1-800-221-0932
APPLICATIONS
INSTALLATION INSTRUCTIONS FOR PART 99-3010S
metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
REV. 10/23/2013 INST99-3010S
PRECAUCIÓN: Metra recomienda desconectar el terminal
negativo de la batería antes de comenzar cualquier
instalación. Todos los accesorios, interruptores y,
especialmente, las luces indicadoras de airbag deben
estar enchufados antes de volver a conectar la batería o
comenzar el ciclo de ignición.
NOTA: Remítase a las instrucciones incluidas con el
radio de postventa.
• Provisión de unidad central DIN con bolsillo
• Provisión de unidad central ISO DIN con bolsillo
• Provisión de unidad central doble DIN
• Provisión de unidad central ISO DIN vertical
• Pintura color plateado para igualar el
acabado de fábrica
• A) Panel de moldura del radio • B) Carcasa del radio • C) Soportes ISO • D) Placa de moldura ISO
• E) Soportes Doble DIN • F) Placa de moldura DDIN • G) Cavidad •H) Interfase • I) Arnés GM de 20-pins
• J) 4-pin a 4-pin arnés resistencia • K) 22-pin a 44-pin arnés Camaro • L) Arnés de calefacción y aire
acondicionado de 18-pins a 10-pins
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
Chevrolet Camaro 2010 y mas
99-3010S
• Herramienta de remoción de panel
• Destornillador Phillips • Herramienta toma
de corriente
HERRAMIENTAS REquERIDAS
A B C D E F G
LKJIH
CABLEADO Y CONEXIONES DE ANTENA
Arnés de cableado:
• Se incluye interfase
Adaptador de antena:
• 40-EU55 - Adaptador de antena
(se venden por separado)

99-3010S99-3010S
2
Indice
Desmontaje del tablero
– Chevrolet Camaro 2010 y mas ......................................................................... 2-3
Preparación del kit ...............................................................................................3
Ensamble del kit
– Provisión de unidad central DIN con bolsillo .........................................................4
– Provisión de unidad central ISO DIN con bolsillo ...................................................4
– Provisión de unidad central doble DIN/ISO DIN vertical .........................................5
Instalación de la interfase Axxess ...................................................................5-6
– Instalación de la interfase ....................................................................................7
– Vehículo de personalización con LCD opcional .....................................................7
– Cambio de la pantalla color de retroiluminación ...................(parte posterior del libro)
1. Desenganche y quite los (2)
paneles de moldura laterales que
corren por la longitud de la consola
central. (Figura A)
2. Quite (1) tornillo de 9/32” de
cada lado del frente de la consola
central. (Figura B)
3. Quite (2) tornillos de 9/32” por lado
de la tapa de la parte posterior
de la consola central y luego
desenganche y quite la tapa.
(Figura C)
4. Quite los (2) tornillos de 9/32”
expuestos debajo de la tapa en
la parte de atrás de la consola.
(Figura D)
Desmontaje del tablero
0
30
70 9
12
19
180
200
320
300
30
100
0
30
70 9
12
19
180
200
320
300
30
100
(Figura A)
(Figura B)
0
30
70 9
12
19
180
200
320
300
30
100
(Figura C)