Metra Electronics 99-7875 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7875/99-7875T
99-7875/99-7875T
APPLICATIONS
Honda Accord 2008-2010
(For Non-Navigation models with Dual Zone Climate controls)
Honda Accord Crosstour 2010
KIT FEATURES
• Painted To Match Factory Dash
99-7875=Charcoal, 99-7875T=Taupe
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
1-800-221-0932
© COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
A
D
C
B
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Cutting Tool
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1729 - Honda harness 2008-up
• 70-1730 - Honda amp interface harness 2008-up
Antenna Adapter:
• 40-HD10 - Honda antenna adapter 2005-up
EFTOOLS REQUIRED:

99-7875/99-7875T DASH DISASSEMBLY
HONDA ACCORD 2008-10 / CROSSTOUR 2010
1
1
Unclip and remove the trim panel at
the left side of the factory radio.
( Figure B)
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
3
Unclip and remove the trim panel
from above the glove box at the right
side of the factory radio. ( Figure A)
2
Unclip and remove the top of the cen-
ter console including the cup holders.
( Figure D)
5
Remove (2) Phillips screws at the bot-
tom edge of the pocket assembly.
( Figure E)
6
Remove the (2) Phillips screws from
the left and right side of the of the
factory radio. (
Figure C)
4
Continue on page 2.
D
B
C
A
E
7
Remove (2) Phillips screws facing up
inside of the pocket below the factory
radio. ( Figure F)
Unclip and remove the pocket assem-
bly. ( Figure G)
8

99-7875/99-7875T DASH DISASSEMBLY
2
Remove (2) Phillips screws facing up
on the bottom of the factory radio.
( Figure H)
9
Unclip and remove the hazard
switch/passenger air bag light
assembly. (Retain the hazard
switch/passenger air bag light
assembly for re-use during kit prepa-
ration.)
13
Remove (4) Phillips screws securing
trim panel at the bottom edge of the
factory radio assembly and remove
the trim panel. (Retain the screws
and trim panel for re-use during kit
preparation.)
14
Remove (9) clips from the back of the
factory radio assembly. (Retain the
clips for re-use during kit prepara-
tion.)
15
Remove (6) Phillips screws securing
the climate controls to the factory
radio assembly and remove the con-
trols from the assembly. (Retain the
screws and climate controls for re-
use during kit preparation.)
11
Remove (4) Phillips screws securing
the a/c vents to the factory radio
assembly and remove the a/c vent
from the assembly. (Retain the
screws and a/c vents for re-use dur-
ing kit preparation.)
12
Unclip the factory radio assembly.
Unplug and remove the radio assem-
bly. (
Figure I)
10
Continue to kit preparation.
I
G
H
F
HONDA ACCORD 2008-10 / CROSSTOUR 2010

99-7875/99-7875T KIT PREPARATION
PAS SENGER
AIRBAG
3
1
Secure the climate controls into the
radio housing using the factory hard-
ware from rear. ( Figure C)
Snap the hazard switch/passenger air
bag light assembly into the radio
housing from front. (
Figure A)
3
Secure the a/c vents into the radio
housing using the factory hardware
from rear. ( Figure B)
2
Attach the clips to the back of the
radio housing. ( Figure E)
5
Secure the trim panel onto the radio
housing using the factory hardware.
( Figure D)
4
Continue to kit assembly.
D
B
C
E
A
HONDA ACCORD 2008-10 / CROSSTOUR 2010

99-7875/99-7875T KIT ASSEMBLY
4
A
B
C
DIN MOUNT RADIO PROVISION WITH POCKET
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
Slide the aftermarket radio into the
DIN cage until it snaps into place.
(Figure B)
2
Snap the pocket into the radio housing.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7875/7875T KIT ASSEMBLY
5
A
B
C
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radio
using the screws supplied with the
radio.
(Figure A)
1
Slide the radio into the Radio Housing
until it snaps into place. (Figure B)
2
Snap the Trim Plate onto the front of
the Radio Housing. (Figure C)
3
Snap the Pocket into the Radio
Housing.
(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7875/99-7875T KIT ASSEMBLY
6
DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION
Cut and remove the center bar from
the Radio Housing. (Figure A)
1
Snap the Double DIN brackets to the
inside edge of the Radio Housing.
(Figure B)
2
Slide the Double DIN or stacked ISO
mount units into the bracket/radio
housing assembly and secure the
unit(s) to the assembly using the
screws supplied with the unit(s).
(Figure C)
3
Snap the Double DIN trim plate onto
the front of the Housing/Radio assem-
bly. (Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C

99-7875/99-7875T FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7

NOTES
8
99-7875/7875T