Metra Electronics 99-9401 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-9401
Socket Wrench • Phillips Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
•DIN Head Unit Provision With Removable Pocket
A) Radio Housing B) Pocket
KIT COMPONENTS
TOOLS REQUIRED:
99-9401
A
APPLICATIONS
2004-2006 Land Rover Freelander
B

Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TABLE OF CONTENTS
99-9401

99-9401
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Put gear shifter into neutral position
then remove shift knob. (Figure A)
2
2004-2006 LAND ROVER FREELANDER
Unclip and remove gear shifter trim
panel.
(Figure B)
3
Unclip and remove rear ashtray
panel from back of center console.
(Figure C)
4
Open center console lid and remove
cubbybox.
(Figure D)
5
DASH DISASSEMBLY
A
P
R
N
D
4
2
1
B
P
R
N
D
4
2
1
C
D

2
99-9401
2004-2006 LAND ROVER FREELANDER
Remove the (2) screws securing the
rear of the center console.
(Figure E)
6
Remove the screw cover in front of
the window switches then remove
the (2) screws exposed underneath.
(Figure F)
7
Unclip and remove the upper console
finisher panel between the a/c vents
and radio..
(Figure G)
8
Remove the (4) screws securing the
center console.
(Figure H)
9
Remove the (2) screws securing the
radio.
DASH DISASSEMBLY
E
F
G
H

3
99-9401
2004-2006 LAND ROVER FREELANDER
KIT ASSEMBLY
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down.
(Figure A)
1
Slide the aftermarket head unit into
the DIN cage until secure.
(Figure B)
2
Slide the included pocket into the
Radio Housing until secure.
(Figure C)
3
Install kit assembly into dash.
4
DIN HEAD UNIT PROVISION
A
B
C

4
99-9401
FINAL ASSEMBLY
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative batteryterminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown belowand the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS

5
NOTES
99-9401

99-9401 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
REV. 06/19/07 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-9401