Metra Electronics 99-7502 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7502
99-7502
APPLICATIONS
Mazda MPV 2000-2006
KIT FEATURES
•DIN Mount Radio Provision
•ISO Mount Radio Provision
A) Radio Housing • B) ISO Snap In Brackets • C) Trim Plate
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver
1-800-221-0932
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
C
TOOLS REQUIRED:

Dash Disassembly
- Mazda MPV 2000-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly
- DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
-ISO DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly .......................................... 4
TABLE OF CONTENTS
99-7502
*Note:
Refer also to the instructions included with the aftermarket radio.

99-7502 DASH DISASSEMBLY
MAZDAMPV2000-2006
A
B
C
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Remove (2) Phillips head screws from
above instrument cluster. ( Figure A)
2
Unclip and remove the radio trim
panel. (Figure B)
3
Remove (4) Phillips screws securing
the radio. Unplug and remove radio.
(Figure C)
4
Continue to kit assembly.

2
99-7502 KIT ASSEMBLY
B
A
DIN MOUNT RADIO PROVISION
Slide the aftermarket radio into the
cage until it snaps into place. (Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1

99-7502 KIT ASSEMBLY
3
B
ISO DIN MOUNT RADIO PROVISION
2
Slide the radio into the radio housing
until it snaps into place. (Figure B)
3 Snap the Trim plate onto the front of
the Radio Housing assembly.
(Figure B)
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
1
A

99-7502 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
4
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown belowand the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’sspecifications.

99-7502
NOTES
5

99-7502 INSTRUCTIONS
1-800-221-0932
REV. 10/12/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-7502
www.metraonline.com