Metra Electronics 99-9100 User manual

METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 9/11/2015 INST99-9100
Installation instructions for part 99-9100
CAUTION! Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con
-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• DIN radio provision
• A) Trim plate (a) • B) Trim plate (b) • C) (2) Screw caps
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • Please visit metraonline.com for more information
Antenna Adapter: • Please visit metraonline.com for more information
• 86-9001 radio removal keys • Pry tool
TOOLS REQUIRED
AUDI A4/A6/A8 1996-1999
TT 2000-2006
99-9100
Dash Disassembly ................................................. 2
Kit Assembly
– A4/A6/A8 1996-1999........................................... 3
– TT 2000-2006...................................................... 3
Table of Contents
BA C

99-9100
2
1. Insert Metra’s 86-9001 into the
slots in the factory radio and pull
the radio out. (Figure A)
2. Disconnect the wiring.
3. For TT models only: Remove (2)
Phillips screws from inside the
radio opening. (Figure B)
Continue to kit assembly
Dash Disassembly
(Figure A)

99-9100
Kit Assembly
AUDI A4/A6/A8 1996-1999
1. Remove the metal DIN sleeve and trim ring from
the aftermarket radio.
Note: Disregard the trim ring, it will not be used in
this application.
2. Slide the sleeve into the radio opening in the dash
and secure by bending the metal locking tabs
down.
3. Locate the factory wiring harness and antenna
connector in the dash, and complete all necessary
connections to the radio. Metra recommends using
the proper mating adapter from Metra and/or
AXXESS. Re-connect the negative battery terminal
and test the radio for proper operation.
4. Slide the radio back into the sleeve until it clicks in.
5. Snap Trim Plate (a) onto the front of the radio.
Audi TT 2000-2006
1. Remove the metal DIN sleeve and trim ring from
the aftermarket radio.
Note: Disregard the trim ring, it will not be used in
this application.
2. Slide the sleeve into the radio opening in the dash
and secure by bending the metal locking tabs
down.
3. Locate the factory wiring harness and antenna
connector in the dash, and complete all necessary
connections to the radio. Metra recommends using
the proper mating adapter from Metra and/or
AXXESS. Re-connect the negative battery terminal
and test the radio for proper operation.
4. Slide the radio back into the sleeve until it clicks in.
5. Secure Trim Plate (b) to the front of the radio
opening using the screws removed during
disassembly.
6. Place the screw caps into the screw openings in
the trim plate.
3

METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 9/11/2015 INST99-9100
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Installation instructions for part 99-9100
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.

METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 9/11/2015 INST99-9100
Instrucciones de instalación para la pieza 99-9100
¡PRECAUCIÓN! Meta recomienda desconectar la terminal negativa
de la batería antes de iniciar cualquier instalación, a menos que el
fabricante del vehículo recomiende lo contrario. Verifique con su
concesionario local si existe más información. Todos los accesorios,
interruptores, paneles de controles de clima y especialmente las lu-
ces del indicador de las bolsas de aire deben estar conectados antes
de reconectar la batería o ciclar la ignición. Además, no quite el radio
de fábrica con la llave en la posición de encendido ni con el vehículo
funcionando. Sería mejor retirar la llave de la ignición y esperar unos
cuantos segundos antes de quitar el radio de fábrica.
• Provisión de radio DIN
• A) Placa de moldura (a) • B) Placa de moldura (b)
• C) (2) Tapas de tornillos
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)
Arnés de cableado: • Visite metraonline.com para más información
Adaptador de antena: • Visite metraonline.com para más información
• Llaves de remoción de radio 86-9001 • Herramienta para hacer palanca
HERRAMIENTAS REQUERIDAS
AUDI A4/A6/A8 1996-1999
TT 2000-2006
99-9100
Desmontaje tablero ............................................... 2
Ensamble del kit
– A4/A6/A8 1996-1999........................................... 3
– TT 2000-2006...................................................... 3
Indice
BA C