Metra Electronics CADILLAC 95-2004 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-2004
•Phillips Screwdriver • Panel Removal Tool • Small Flat Blade Screwdriver • Cutting Tool
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
•DDIN Head Unit Provision
•ISO Stacked Head Unit Provision
• ( A) DDIN Brackets • ( B) DDIN Trim Plate • ( C) (4) Speed Clips • ( 4) Phillips Head Screws
KIT COMPONENTS
TOOLS REQUIRED:
A
APPLICATIONS
Cadillac
1997-2001 Catera
1996-1999 Deville
(Column Shift Only)
B
95-2004
METRA. THE WORLD’S BEST KITS.™
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
HARNESS:
ANTENNA ADAPTER:
• GMRC-03 - 1997-2002 Cadillac Interface W/O Onstar
• GMOS-06 - 1997-2002 Cadillac Interface W/ Onstar
• 40-GM10 - GM Antenna Adapter
CD

TABLE OF CONTENTS
95-2004
Dash Disassembly
1997-2001 Cadillac Catera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1996-1999 Cadillac Deville ( Column Shift Only) ............. 1
Kit Preparation
1997-2001 Cadillac Catera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1996-1999 Cadillac Deville ( Column Shift Only) ............. 2
Kit Assembly
1997-2001 Cadillac Catera / 1996-1999 Cadillac Deville ( Column
Shift Only)
DDIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ISO Stacked Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . 3
K NOWLEDGE IS P OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends using
MECP certified technicians.

95-2004
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Remove (1) Phillips head screw from
inside the ashtray and remove ash-
tray. (Figure A)
2
Remove screw covers from the radio
trim panel. Remove traction control
and hazard switch covers. Then
remove switches by depressing tabs
and pulling outward.
(Figure B)
3
Remove radio trim panel and unplug
any remaining harnesses from the
panel. (Figure C)
4
5
Remove (2) Phillips head screws
securing the radio. Unplug and
remove the radio.
6
Remove (4) Phillips head screws
from behind covers and ashtray.
1997-2001 CADILLAC CATERA
1996-1999 CADILLAC DEVILLE
Unsnap and remove radio trim panel.
(Open glove box to access.)
(Figure A)
2
Pinch the side clips to disengage
radio. Unplug and remove radio.
3
DASH DISASSEMBLY
A
6:59
6:59
A
C
B

95-2004
KIT PREPARATION
1997-2001 CADILLAC CATERA
A
B
2
1996-1999 CADILLAC DEVILLE
Cut and remove the three shaded
tabs on both brackets. (Figure A)
Cut and remove the shaded tab from
both brackets, and both of the tabs
on the trim plate. (Figure B)
1
1
Install (4) speed clips into the sub-
dash mounting positions. (Figure C)
2
C

3
95-2004
KIT ASSEMBLY
DOUBLE DIN / STACKED ISO DIN
HEAD UNIT PROVISIONS
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the unit for proper operation.
1
Attach the Double DIN brackets to
the inside edge of the Double DIN
trim plate. (Figure A)
2
Slide the bracket/radio housing
assembly over the Double DIN head
unit and secure using the screws
supplied with the radio.
(Figure B)
3
4
Reassemble dash in reverse order of
disassembly.

4
NOTES
95-2004

5
NOTES
95-2004

INST95-2004
1-800-221-0932 www.metraonline.com
REV. 12/01/09 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST95-2004
METRA. THE WORLD’S BEST KITS.™