Metra Electronics 99-9105 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-9105
*86-9001 Head Unit Removal Tool • Flat Blade Screwdriver Or Panel Removal Tool
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
APPLICATIONS
Audi A4 2000-2001
(Symphony Radio Only)
•DIN radio provision with pocket
•ISO radio provision with pocket
• Double DIN radio provision
A) Radio Housing • B) Pocket • C) Trim Plate • D) ISO Brackets • E) Double DIN Trim Plate
• F) Double DIN Brackets
KIT COMPONENTS
TOOLS REQUIRED:
99-9105
AB
Note: Twosets of the head unit removal tools are recommended for
easier removal of factor head unit.
F
C
E
D

Dash Disassembly
-Audi A4 2000-2001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly
-DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 2
-ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 3
-Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Final Assembly ...................................5
TABLE OF CONTENTS
99-9105

1
AUDI A4 2000-2001
AS
FM
AM
SAT
TAPE SCAN
RDS
TONE
MENU
LOAD
CD
A
99-9105
1
2
Disconnect the wiring.
Continue to kit assembly.
Insert Metra’s 86-9001 into the
slots in the factory radio and pull
the radio from the dash.
(Figure A)
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
3
DASH DISASSEMBLY

2
99-9105 KIT ASSEMBLY
Snap the pocket into the Radio
Housing until secure.
(Figure C)
3
Slide the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
(Figure A)
1
Slide the aftermarket radio into the
cage and secure. (Figure B)
2
DIN RADIO PROVISION WITH POCKET
A
B
C
Continue to final assembly.

3
99-9105 KIT ASSEMBLY
Slide the radio into the radio
opening until the side clips
engage.
(Figure B)
2
Snap the ISO Trim Plate into the
Radio Housing.
(Figure C)
3
Snap the pocket into the radio
housing.
(Figure C)
4
Mount the ISO Brackets to the
radio with the screws supplied
with the unit. (Figure A)
1
ISO RADIO PROVISION WITH POCKET
A
B
C
Continue to final assembly.

4
99-9105 KIT ASSEMBLY
Slide the Double DIN radio into the
Double DIN bracket/radio housing
assembly and secure the unit to the
kit using the screws supplied with
the radio.
(Figure C)
3
Cut and remove center divider
from radio housing.
(Figure A)
1
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Snap the Double DIN trim-plate onto
the housing/radio assembly.
(Figure D)
4
DOUBLE DIN RADIO PROVISION
A
B
C
D
Continue to final assembly.

5
FINAL ASSEMBLY
Make wiring connections using the EIA color code chart shown belowand the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
FINAL WIRING CONNECTIONS
99-9105
FINAL ASSEMBLY
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray/ Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
METRA / EIA WIRING CODE
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Snap radio housing assembly into factory radio opening.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D

99-9105 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
REV.04/17/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-9105