Metra Electronics 95-9313B User manual

METRA. The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
REV. 1/25/2017 INST95-9313B
Installation instructions for part 95-9313B
CAUTION! All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
• ISO DDIN radio provision
• Painted matte black
• Relocates the factory climate control and switches
• Parts included to modify the factory airbox
• A) Radio trim panel • B) Back up housing • C) Radio brackets • D) Climate and switch panel housing
• E) Airbox cover • F) Cutting template • G) Climate bracket • H) Actuator arm • I) (1) #6 x 1/2” Phillips screw
• J) (4) #8 x 1/2” Phillips screws • K) (2) #8 x 3/8” Phillips screws • L) (2) panel clips • M) Vent door
KIT FEATURES
KIT COMPONENTS WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-8590 • 70-9003 (nav models 02-06)
Antenna Adapter: • 40-VW10 40-EU10 (nav models 02-06)
• Panel removal tool • Phillips screwdriver • Pick tool
TOOLS REQUIRED
BMW 3-Series 1999-2005,
3-Series (coupe, convertible) 2006, M3 2001-2006
(for factory switch panel with one long opening)
95-9313B
AC
G I JH
D E
K L M
B
Dash Disassembly ..............................................2-5
Sub-dash airbox modifications..........................6-9
Kit Assembly
–ISO DDIN radio provision.................................... 10
Climate and Switch Panel Assembly .................. 11
Table of Contents
F

95-9313B
2
Dash Disassembly
1. Unclip and remove the trim panel
above the glove box. (Figure A)
2. Unclip and remove the trim panel
above the factory radio. (Figure B)
3. Remove (2) Phillips screws
securing the radio and then unplug
and remove the radio. (Figure C)
Continued on the next page
(Figure A) (Figure C)(Figure B)

95-9313B
(Figure D)
4. Unsnap and remove the climate
control panel. (Figure D)
5. Pull straight up on the shift knob to
remove. (Figure E)
6. Unclip and remove the boot around
the shift selector. (Figure F)
Continued on the next page
3
Dash Disassembly
(Figure E) (Figure F)

95-9313B
4
Dash Disassembly
7. Remove (2) Phillips screws
securing the shift selector trim
panel, and then unclip and remove
the panel. (Figure G)
8. Open the upper door on the lower
switch panel. Using a pick tool, or
something suitable, disengage (2)
clips in the upper corners of the
tray to remove the tray and door.
(Figure H)
(Figure G) (Figure H)

95-9313B
9. Remove (4) Phillips screws now
exposed securing the lower switch
panel, and then unplug and remove
the panel. (Figure I)
Note: All of the switches
will need to be removed and
installed into the new switch
panel provided.
10. Remove (2) Phillips screws, and
then unclip and move aside the
vent assembly above the radio
opening. It is not necessary to
remove the assembly. But if
desired, there will be a cable
attached to the assembly that will
need to be removed. (Figure J)
11. For non-NAV equipped cars,
remove (2) Phillips screws
securing the plastic radio/climate
housing from the radio/climate
cavity, and then remove.
Continue to kit assembly
5
(Figure I) (Figure J)
Dash Disassembly

95-9313B
Sub-dash airbox modifications
6
1. Remove (4) metal retaining clips
holding the air box front panel in
place and remove the panel.
Note: One of the retaining clips
will be reused in step 7.
(Figure A)
2. Clip the cutting template over the
top edge of the air box, mark for
cutting, remove the template, then
and cut the marked area.
(Figure B)
Continued on the next page
(Figure A) (Figure B)

95-9313B
7
Sub-dash airbox modifications
3. Remove the upper actuator arm
from the passenger vent door.
Remove the lower actuator arm
from the vent doors. Unclip the
passenger side first and then the
drivers side. (Figure C)
4. Remove the passenger side vent
door. Unclip from the bottom, then
push and rotate the top clip out of
the slot in the airbox. (Figure D)
Note: Remember the orientation
of the vent door arm (approx.
11:00) when removing to ease in
reinstallation.
Continued on the next page
(Figure C) (Figure D)

95-9313B
8
Sub-dash airbox modifications
(Figure E) (Figure F)
5. Replace the factory passenger side
vent door with the supplied vent
door. Rotate the vent door into the
upper slot and clip into the lower
socket. (Figure E)
6. Replace the factory actuator
arm with the supplied actuator
arm. Clip the drivers side in first
and then the passenger side.
Reconnect the upper actuator arm
to the passenger vent door.
(Figure F)
Continued on the next page

95-9313B
9
Sub-dash airbox modifications
7. Set the air box cover into place
and secure the right side with the
metal retaining clip removed in
step 1. Secure the left side with
the (1) #6 x 1/2” Phillips screw
supplied. (Figure G)
8. Metra recommends using tape
along the upper edge of the air box
cover where the cut was made.
Duct tape or A/C aluminum tape is
suggested. (Figure H)
Continue to kit assembly
(Figure G) (Figure H)
Tape the shaded area
Clip
location
Screw
location

95-9313B
10
(Figure B)
(Figure C)(Figure A)
1. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
2. Attach the back-up housing to the
radio/bracket assembly with the (4)
#8 x 1/2” Phillips screws supplied.
(Figure B)
3. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio and
climate control panel. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Test the radio for proper
operation.
Note: After all testing has been
performed, disconnect the
climate control panel, relocate
the harness to the lower switch
panel area, and then proceed to
the next step.
Kit Assembly
4. Secure the completed assembly
into the radio/climate cavity using
the (2) #8 x 3/8 inch screws
supplied.
5. Secure the vent assembly to the
vehicle using the (2) factory Phillips
screws removed in step 10 of dash
disassembly.
6. Attach (2) panel clips provided
with the kit onto the radio trim
panel (Figure C), and then attach
the panel to the radio assembly.
Secure the assembly to the vehicle
using the (2) factory Phillips
screws removed in step 3 of dash
disassembly.
Continue to climate and switch
panel assembly