Metra Electronics 99-7427 User manual

METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 7/16/2015 INST99-7427
Installation instructions for part 99-7427
CAUTION! Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con
-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• DIN Radio Provision With Pocket
• ISO DIN Radio Provision With Pocket
• PAINTED TO MATCH FACTORY DASH:
99-7427B=BLACK, 99-7427G=GRAY
• Textured To Match Factory Dash
• A) Radio Housing • B) Trim Plate • C) ISO Brackets • D) Module Brackets • E) (2) Phillips Head Screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552
Antenna Adapter: • 40-NI12
• Torx Screwdriver • Panel Removal Tool • Phillips Screwdriver
TOOLS REQUIRED
Nissan Maxima 2009-2014 (non nav models) (w/o tech package)
99-7427
A B C D E
Dash Disassembly ................................................. 2
Kit Preparation....................................................... 2
Kit Assembly
–DIN Radio Provision With Pocket........................... 3
– ISO DIN Radio Provision With Pocket .................... 3
Table of Contents

99-7427
2
1. Unclip and remove the panel above
the radio including the a/c vents and
the climate controls. Unplug and
remove the panel. (Figure A)
2. Unclip and remove the panel below
the radio. (Figure B)
3. Remove (6) Phillips screws securing
the radio. Unplug and remove the
radio. (Figure C)
4.
Remove (4) Torx head screws securing
each side bracket to the factory radio.
Remove (1) Torx head screw from each
side of the module below the radio,
and then remove the radio and module.
Retain the module and (2) screws for
re-use during kit assembly. (Figure D)
Continue to kit preparation
Dash Disassembly Kit Preparation
(Figure C)
1. Attach the module brackets to the
radio housing using (2) Phillips head
screws supplied. (Figure A)
2. Secure the module to the completed
assembly using (2) factory Torx
head screws removed from dash
disassembly. (Figure B)
Continue to kit assembly
X
OFF
PASS
AIR
BAG
CDCHANGER
AUXIN
(Figure B)
(Figure A) (Figure D)
(Figure A)
(Figure B)

99-7427
Kit Assembly
(Figure A) (Figure A)
(Figure B) (Figure B)
DIN radio provision with pocket
1. Remove the metal DIN sleeve from
the aftermarket radio.
2. Slide the sleeve into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
3. Slide the radio back into the sleeve
until it clicks in.
(Figure B)
4. Locate the factory wiring harness
and antenna plug in the dash and
make all necessary connections to
the radio. Metra recommends using
the proper mating adapters from
Metra and/or AXXESS. Re-connect
the negative battery terminal and
test the radio for proper operation.
5. Mount the new radio assembly into
the dash and reassemble the dash in
reverse order of disassembly.
ISO DIN radio provision with pocket
1.
Remove the metal DIN sleeve and
trim ring from the aftermarket radio.
2. Mount the ISO brackets to the radio
using screws supplied with the
radio.
(Figure A)
3. Slide the completed assembly into
the Radio Housing until it clicks in.
(Figure B)
4. Snap the Trim Plate onto the front
of the Radio Housing.
(Figure B)
5. Locate the factory wiring harness
and antenna plug in the dash and
make all necessary connections
to the radio. Metra recommends
using the proper mating adapters
from Metra and/or AXXESS.
Re-connect the negative battery
terminal and test the radio for
proper operation.
6. Mount the new radio assembly into
the dash and reassemble the dash
in reverse order of disassembly.
3

METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 7/16/2015 INST99-7427
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Installation instructions for part 99-7427
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.