Metra Electronics 95-3027 User manual

Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 5/22/19 INST95-3027
INSTALLATION INSTRUCTIONS
95-3027
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DDIN radio provision
APPLICATIONS
Chevrolet S-10 Blazer 1998-2002*
Chevrolet S-10 Pickup 1998-2002*
GMC Jimmy (a.k.a. Jimmy Envoy) 1998-2001
GMC Sonoma 1998-2002*
Isuzu Hombre 1998-2000
* Only for early 2002 models denoted by a DIN and a half size radio
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32” socket wrench • cutting tool • Scribe tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-1858
Antenna Adapter: 40-GM10
A B
GM Small trucks/SUV’s 1998-2002

1.800.221.0932
|
MetraOnline.com
2
1. Remove (2) 9/32” screws securing the
driver’s side knee bolster to the dash.
(Figure A)
2. Slightly pull down on the knee bolster
to expose the 9/32” screws securing the
base of the dashboard trim panel, then
remove the screws. (Figure A)
3. Remove (1) Phillips screw in the
instrument cluster.
4. Unclip and remove the dashboard trim
panel, using caution not to damage the
hazard switch while removing the panel.
5. Remove (2) 9/32” screws securing the
radio. Slide the radio out, then unplug
and remove the radio.
Continue to Kit Preparation
(Figure A)
DASH DISASSEMBLY KIT PREPARATION
1. Place the radio trim panel over the
factory dashboard trim panel. (Figure A)
2. Using a scribe tool, score the area in the
radio section to be cut. (Figure B)
3. Remove the radio trim panel , then cut
the scored area with a cutting tool.
Continued on the next page
(Figure A)
(Figure B)
Remove shaded area
Mark here

REV. 7/31/2018 INST95-3027 3
KIT ASSEMBLY
(Figure A)
KIT PREPARATION (CONT.)
4. Slide the radio trim panel into the
bottom opening of the factory
dashboard trim panel, then clip in the
top portion. Note, if the center bar of
the radio trim panel is bowed, file the
opening of the factory dashboard trim
panel to fit better. (Figure C)
5. Cut the sub-dash to allow room for the
radio assembly. (Figure D)
Continue to Kit Assembly (Figure C)
(Figure D)
1. Secure the radio brackets to the radio
using the screws supplied with the
radio. (Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
3. Secure the radio assembly to the dash
using the factory screws.
4. Reassemble the dash in reverse
order of disassembly to complete the
installation.
Remove
shaded area

Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 5/22/19 INST95-3027
INSTALLATION INSTRUCTIONS
95-3027
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
If you are having difficulties with the installation
of this product, contact our Tech Support line
either by phone at 1-800-253-TECH, or email at
[e-mail]. Before
doing so, look over the instruction booklet a
second time and ensure that the installation was
performed exactly as the instruction booklet
is stated. Have the vehicle apart and ready to
perform troubleshooting steps before contacting
Metra/Axxess Tech Support.