Metra Electronics 99-7378B User manual

CAUTION! All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 8/22/18 INST99-7378B
INSTALLATION INSTRUCTIONS
99-7378B
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted scratch-resistant matte black
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (2) #8 x 3/8” Phillips screws TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-7306
Antenna Adapter: 40-KI11
Steering wheel control interface: ASWC-1
A CB D
Kia Sportage LX (with base radio†) 2017-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
† Base radio is an non-touchscreen radio

1.800.221.0932
|
MetraOnline.com
2
1. Unclip and slide the top of the center
console back slightly. (Figure A)
2. Unclip and remove the panel on the
end of the passenger side of the dash,
then remove (1) Phillips screw exposed.
(Figure B)
3. Unclip and remove the dash panel above
the glove box. (Figure C)
DASH DISASSEMBLY
4. Remove (2) Phillips screws securing the
radio display and a/c vent panel, then
unclip and remove the panel. (Figure D)
5. Remove (4) Phillips screws securing the
radio. Slide the radio out, then unplug
and remove the radio. (Figure E)
Continue to Kit Preparation
(Figure D)
(Figure E)
(Figure A)
(Figure B)
(Figure C)

REV. 8/22/2018 INST99-7378B 3
KIT PREPARATION
(Figure A) (Figure A)
(Figure B) (Figure B)
Radio Trim Panel Installation
From the factory radio trim panel:
1. Remove (4) Phillips screws securing the
inner trim panel, then remove the panel.
(Figure A)
To the factory radio trim panel:
2. Secure the 99-7379B radio trim panel to
the panel using with the factory screws.
(Figure B)
Continue to Kit Assembly
1. Secure the radio brackets to the pocket
using the (2) #8 x 3/8” Phillips screws
provided. (Figure A)
2. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket
assembly, then secure it to the assembly
using the screws supplied with the radio.
(Figure B)
4. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or AXXESS. Test the radio for proper
operation.
5. Secure the radio assembly to the dash
using the factory screws.
6. Reassemble the dash in reverse order of
disassembly to complete the installation.
KIT ASSEMBLY

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before
doing so, look over the instructions a second time, and make
sure the installation was performed exactly as the instructions
are stated. Please have the vehicle apart and ready to perform
troubleshooting steps before calling.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 8/22/18 INST99-7378B
INSTALLATION INSTRUCTIONS
99-7378B