X
37"
36"
35"
34"
33"
32"
31"
Do Not
Use
Bottom
Groove
II. BASIC WORKBENCH ASSEMBLY
Locate the 2 front (unslotted) and 2 rear (slotted) Posts and the Footrest Frame. First lay carpet or
similar material down on floor to protect finish. Attach plastic sleeves at the first or second groove near
the bottom of each Post. Assemble the 4 Posts and the Footrest Frame as shown above, with the unit
on its back, by sliding the Posts up into the collars on the Footrest Frame.
Note that the Footrest can be attached either as
shown above or with the long footrest tube closer to the back of the bench. Put 4 Adjustable Foot
Assemblies together as shown above and install in the bottom ends of the 4 Posts. Set the bench
upright and seat the Footrest Frame collars firmly down onto the plastic sleeves, using a hammer and
block of wood or rubber mallet (to protect finish).
Should you ever desire to readjust bench height, carefully lay Workbench down on its back , grip foot
posts firmly with vice-grip pliers, then tap against pliers with hammer or mallet until Foot Assembly
comes back out of Post. Then move split sleeves to different groove locations and proceed as above.
Rotate Rear Posts care-
fully so the slots are facing exactly front and rear.
2
3
4
END VIEW
FOOTREST FRAME
H-FRAME IN PLACE
FRONT POST
FRONT POST
Set ALUMINUM
Split Sleeves on
TOP Groove
on front Post
Set
Sleeves on
the same
Groove
as on the
Front Posts
ALUMINUM
Split
FRONT OF
TOP FRAME
ROUND HOLES
KEYHOLE- SHAPED HOLES
KEYHOLE- SHAPED HOLES
ROUND HOLES
REAR
KEYHOLES
SHOULDER RIVETS
Set
Plastic
Split
Sleeves
on
first or
second
Groove
REAR POST - NOTE SLOTS FACING UP.
NOTE BLACK RIMS AT
BOTTOMS OF BLUE POSTS
BACK DOWN
HIGH PROFILE LOW PROFILE
Set Benchtop in place on
the Top Frame and
ensure that it is centered
left-to-right and all the
way back against the
Rear Posts. Attach it
with the screws provided
as shown.
1SMALLER
END
TOWARD
TOP
SMALL SPLIT SLEEVE
JAM NUT
FOOT PAD
LEVELING FOOT PAD
X
ADJUSTABLE FEET
To attach components: Begin by snapping a 2-piece plastic
sleeve together around each post at the groove indicated in
the instructions that follow. Be sure the smaller end of the
sleeve (and the ridge inside the sleeve) is toward the top of
the post. Note: for attaching the top frame, use the aluminum
split sleeves provided.
OPTION: ATTACH DRAWER ASSEMBLY
Attach Starter Drawer Assembly
as shown at left. First insert the
two straight pins on the back of the
drawer assembly into two ROUND
HOLES in the back of the top
frame (under the benchtop). Note
that drawer can be attached under
the top at several positions left-to-
right. Next, insert the shoulder
rivets on the top front of the
drawer assembly into two
KEYHOLES in the front of the top
frame. Be sure the rivets drop
down into the narrow parts of the
key holes and lock in place.
Optional Add-on Drawer attaches
to sides of Starter Drawer
Assembly with screws as shown
below.
HIGH PROFILE ONLY
TOP BRACE
5High Profile only - attach Top Brace on
plastic sleeves set on the third groove
down from the top of each Rear Post.
4. After
Workbench
is upright in
desired
location,
rotate Foot
Pad for fine
adjustment,
then tighten
jam nut.
1. Thread jam nuts
half way onto the 4
Foot Pads as
shown, then screw
leveling feet into
foot posts - tighten jam nuts later.
2. Choose the approximate bench height you want and place the
small split sleeves on the appropriate grooves on the 4 Foot Posts
as shown at right (same groove on all 4).
3. Insert the completed Foot Assemblies into the bottom ends of the
blue bench posts.
Snap on
"C" Rings.
After placing the aluminum split sleeves on
the posts as shown, attach the top frame. Be
sure to orient the top frame correctly
Seat the frame firmly using a
hammer with a block of wood to protect the
finish. Then secure in place by tapping the
"C" rings into place.
so that
the front member that is welded directly to
the collars is positioned toward the front of
the bench.
