MICRO-AIR CLEAN AIR BOOTH User manual

This manual contains specific cautionary statements relative to worker safety. Read this manual thoroughly and follow as directed. It is
impossible to list all of the hazards of dust control equipment. It is important that use of the equipment be discussed with a Micro-Air
Representative. Persons involved with the equipment or systems should be instructed to operate in a safe manner.
CLEAN AIR BOOTH
INSTALLATION MANUAL
MICRO AIR INC.
www.microaironline.com

2
BOOTH ASSEMBLY MICRO AIR
CONTENTS
TABLE 1 –8’ W Booths
TABLE 2 –12’ W & 16’ W Booths
NOTE: Refer to pages 13-16 for assembled drawings of each booth.
COMPONENT DESCRIPTION CABIR1-888 CABIN1-888 CABUR1-888 CABUN1-888 CABIR2-888 CABIN2-888 CABUR2-888 CABUN2-888
INSULATED YES YES NO NO YES YES NO NO
REGAIN YES NO YES NO YES NO YES NO
SIDE PANEL 8 8 8 8 8 8 8 8
BACK PANEL 2 2 2 2 0 0 0 0
TOP PANEL 3 4 3 4 3 4 3 4
REGAIN TOP PANEL 1 0 1 0 1 0 1 0
VERTICAL SUPPORT 8 8 8 8 8 8 8 8
HEADER 1 1 1 1 1 1 1 1
HEADER BRACE 0 0 0 0 0 0 0 0
HORIZONTAL SUPPORT 3 3 3 3 3 3 3 3
HORIZONTAL SUPPORT BRACE 0 0 0 0 0 0 0 0
10" WYE 1 0 1 0 0 0 0 0
CABINET CONNECTION PLATE 2 2 2 2 0 0 0 0
#8-18x3/4" SLF DRILLING/TAPPING 32 032 032 032 0
1/4"-20x3/4" BOLT 252 252 252 252 204 204 204 204
1/4"-20 NUT 222 222 222 222 168 168 168 168
1/4" FLAT WASHER 474 474 474 474 372 372 372 372
1/4" LOCK WASHER 474 474 474 474 372 372 372 372
COMPONENT DESCRIPTION CABIR3-1288 CABIN3-1288 CABUR3-1288 CABUN3-1288 CABIR4-1688 CABIN4-1688 CABUR4-1688 CABUN4-1688
INSULATED YES YES NO NO YES YES NO NO
REGAIN YES NO YES NO YES NO YES NO
SIDE PANEL 8 8 8 8 8 8 8 8
BACK PANEL 0 0 0 0 0 0 0 0
TOP PANEL 6 8 6 8 6 8 6 8
REGAIN TOP PANEL 3 0 3 0 2 0 2 0
VERTICAL SUPPORT 8 8 8 8 8 8 8 8
HEADER 2 2 2 2 2 2 2 2
HEADER BRACE 1 1 1 1 1 1 1 1
HORIZONTAL SUPPORT 6 6 6 6 6 6 6 6
HORIZONTAL SUPPORT BRACE 3 3 3 3 3 3 3 3
10" WYE 0 0 0 0 0 0 0 0
CABINET CONNECTION PLATE 0 0 0 0 0 0 0 0
#8-18x3/4" SLF DRILLING/TAPPING 48 048 064 064 0
1/4"-20x3/4" BOLT 297 294 297 294 324 324 324 324
1/4"-20 NUT 255 252 255 252 276 276 276 276
1/4" FLAT WASHER 552 546 552 546 600 600 600 600
1/4" LOCK WASHER 552 546 552 546 600 600 600 600

3
BOOTH ASSEMBLY MICRO AIR
Note: Before assembly, remove parts from packaging and inspect for any possible damage
incurred during shipping. Identify each part and verify quantities.
EQUIPMENT REQUIRED
1. Step ladders
2. Overhead Crane/Forklift
3. Lifting Straps
4. 3/8” Wrenches and/or Ratchet with appropriate sockets
5. C-clamp pliers
6. Hammer or mallet
7. Protective/Work gloves
WARNING!!
Proper handling and care must be taken when assembling equipment. Use proper eye wear and
gloves. Pieces can be heavy and sharp around edges.

4
BOOTH ASSEMBLY MICRO AIR
INSTALLATION
1. Assemble side panels to CAB module with the appropriate 1/4" hardware (See FIG. 1). Each
panel is bolted on in twelve places onto the CAB module. Bolt through holes closest to the
inside flange of the side panels. Make sure side panels are flush with CAB module at the
bottom. Side panels should stick out 1.25” from CAB side wall. Bolt down side panels to
ground using at least 2 anchors per panel (see FIG. 2). Anchors are NOT provided.
NOTE: For booths with a single CAB module, install back panels to CAB module first.
Stand back panels next to CAB module. Use cabinet connection plate to install the back
panels to the CAB module (see FIG. 3). Once the back panels are installed, bolt side
panels to the back panels.
FIG. 1
¼” Hardware
CAB
Module
Side
Panel
Side
Panel
CAB
Module
¼” Hardware

5
BOOTH ASSEMBLY MICRO AIR
FIG. 2 FIG. 3
2. Assemble top panels together (Skip this step for 8’ W booths). The top panel assemblies
consist of two panels. The outside edge of the panel is 5.25” to the center of the mounting
slot. The inside edge is 4.00” to the center of the mounting slot. The outside edges of the
panels do not have any mounting slots (see FIG. 4). The inside ends of each top panel are
bolted together in three places. If the top panels are insulated, bolt through the holes’
nearest flange (See FIG. 5). Make sure sides of panels lay flush with each other.
FIG. 4
Anchor
Side
Panel
Top
Panel
Back
Panel
CAB
Module
Connection
Plate
¼” Hardware

6
BOOTH ASSEMBLY MICRO AIR
FIG. 5
NOTE: For the 12’ W booth with regain, the regain portion of the top panel assembly will
consist of 3 top panels bolted together. The outer panels are 48.25” wide each and the mid
panel is 50.00” wide. The distance between mounting slots is 8.00” in the middle. The
outside panels do not have mounting slots (See FIG. 6).
FIG. 6
¼” Hardware
Top
Panel

7
BOOTH ASSEMBLY MICRO AIR
3. Seat horizontal supports at the front of the top panel segment (Skip this step for 8’ W
booths). Bolt together the horizontal supports with the horizontal support brace (12 bolts
total, see FIG. 7).
NOTE: The horizontal support braces will have holes on the top flange. 8’ W booths do not
include horizontal support braces.
FIG. 7
4. With top panel segment and support braces together, use c-clamp pliers to hold assembly
together prior to transfer onto the CAB module and side panels (see FIG. 8). If no c-clamps
are available it is possible to use bolts and nuts provided to keep the assembly secure but
they will need to be removed prior to bolting on the next top panel segments (see FIG. 9).
NOTE: For ease of assembly it is suggest to assemble each top panel segment in front of
CAB/BOOTH unit.
FIG. 8
¼” Hardware
Horizontal Support
Brace
C-clamp Pliers
Horizontal Support
Top
Panel
Top
Panel
Horizontal
Support

8
BOOTH ASSEMBLY MICRO AIR
FIG. 9
5. Once the top panel is set flush on the side panels, bolt to the CAB module and panels (see
FIGS. 10, 11). The top panel assembly will bolt to the CAB module and in the side panels.
Make sure to bolt through holes located nearest inside flange of panels.
Note: Do not tighten bolts of the top panel segment until next top panel segment is in place.
Top Panel
Segment
CAB
Module
Side
Panel

9
BOOTH ASSEMBLY MICRO AIR
FIG. 10
FIG. 11
¼” Hardware
CAB
Module
CAB
Module
Side
Panel
¼” Hardware
Typ. (3) places
per side panel
Top Panel
Segment
Side
Panel
Top Panel
Segment

10
BOOTH ASSEMBLY MICRO AIR
6. Bolt the next set of side panels to the booth. These side panels are joined with the vertical
supports. Make sure the flange on the vertical support sits on the outside of the side panels
(see FIGS. 12, 13).
FIG. 12
FIG. 13
7. Assemble and install the next top panel segment following steps 2-5.
When aligning horizontal supports use hammer or mallet to tap edge into place
Assemble side panels and vertical supports following step 6.
Repeat process 2 more times.
Tighten down all bolts once all panels and braces have been installed.
NOTE: The last top panel segment that will go on the booth will use two Header beams (8’
W booths only utilize one Header beam), and the Header Brace in lieu of the horizontal
support and horizontal brace. The header brace is bolted onto both headers with 12 bolts
and bolted to the top panels through the bottom side (see Figs. 14, 15, 16).
Side
Panel
Top Panel
Segment
Side
Panel
¼” Hardware
Vertical Support
Proper Vertical
Support Orientation
Top View

11
BOOTH ASSEMBLY MICRO AIR
FIG. 14 FIG. 15
FIG. 16
¼” Hardware
Header
Side
Panel
Top Panel
Header
Brace
Header
Side
Panel
Vertical
Support
Header

12
BOOTH ASSEMBLY MICRO AIR
REGAIN
NOTE: HEPA filtration is recommended for use with ALL Regain applications
1. Remove parts from packaging and inspect for any possible damage incurred during
shipping.
2. Set the Regain module on top of the booth.
3. Using the provided self-drilling/self-tapping screws, attach the Regain module to the
regain panel (see FIG. 17).
4. Mount the grilles on the Regain panel with the provided hardware. The vanes of the grille
can be redirected slightly to adjust Regain airflow.
5. Once the regain assembly is installed, connect the 10” hose between the regain
adjustment plate can be moved to provide the best return air flow for your particular
application.
NOTE: It is recommended to install the Regain assembly through the collar opening on
the assembly. For insulated booths, the Regain grilles will be installed on the panels. For
un-insulated booths, use hardware provided in register package to install to top panel.
FIG. 17
Screws
Regain
Module
Top Panel
Regain Assembly
Regain
Grille

13
BOOTH ASSEMBLY MICRO AIR
CABIR1-888 & CABUR1-888
CABIN1-888 & CABUN1-888

14
BOOTH ASSEMBLY MICRO AIR
CABIR2-888 & CABUR2-888
CABIN2-888 & CABUN2-888

15
BOOTH ASSEMBLY MICRO AIR
CABIR3-1288 & CABUR3-1288
CABIN3-1288 & CABUN3-1288

16
BOOTH ASSEMBLY MICRO AIR
CABIR4-1688 & CABUR4-1688
CABIN4-1688 & CABUN4-1688

17
BOOTH ASSEMBLY MICRO AIR
NOTES
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________

18
BOOTH ASSEMBLY MICRO AIR
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
L2005
08/19