MicroBoards Technology BD Pro Series User manual

BD Pro Series
User’s Manual
www.microboards.com Version 2.2

Microboards Technology, LLC
2

BD Pro Series
3
Table of Contents
Introduction ................................................................................................................ 5
Unpacking your system.............................................................................................. 5
Installation.................................................................................................................. 5
The LCD Control Panel .......................................................................................... 6
Hardware Description............................................................................................. 7
Main Menu ................................................................................................................. 8
Setting Counters ...................................................................................................... 10
Using the BD Pro Series Duplicator ......................................................................... 10
Copy..................................................................................................................... 10
Test ...................................................................................................................... 11
Compare .............................................................................................................. 11
Test + Copy.......................................................................................................... 12
Copy + Compare .................................................................................................. 12
Select Burn Speed ............................................................................................... 12
Select Source....................................................................................................... 12
Erase.................................................................................................................... 12
Hard Drive Setup.................................................................................................. 12
Mix Audio Tracks.................................................................................................. 13
Setup.................................................................................................................... 14
Utilities.................................................................................................................. 14
Manage Accounts................................................................................................. 14
AutoCopy ............................................................................................................. 15
Shutdown ............................................................................................................. 15
The Setup Menu ...................................................................................................... 16
The Utilities Menu .................................................................................................... 20
Using CopyLock Video Protection............................................................................ 21
Specifications – BD Pro Series ................................................................................ 23
Supported Formats .................................................................................................. 23
Technical Support .................................................................................................... 23
Appendix 1: Menu List ............................................................................................. 24
Appendix 2: Error Messages.................................................................................... 25

Microboards Technology, LLC
4
Any unauthorized modification to this equipment may result in the revocation by the FCC of the user’s
authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and antenna
•Connect the equipment into an outlet on a circuit different than that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
This product is in conformity with the EMC Directive (89/336/EEC) through compliance with the following
European standards: EN 55022, EN 55024. The CE mark has been affixed in accordance with the CE
Marking Directive 93/68/EEC.
Canadian Department of Communications (DOC) Statement
This Class B digital apparatus complies with the Canadian ICES-003 Issue 4:2004. Cet appareil numerique de la classe B est
conforme a la norme NMB-003 du Canade.

BD Pro Series
5
Introduction
The BD Pro Series includes models containing 4, 7, and 10 recorders. The BD Pro Series
models include an internal hard drive for convenient master storage.
Each is a high speed CD, DVD, and BD Recordable duplication system from Microboards
Technology, LLC.
Regardless of the number of drives, the BD Pro is perfect for any user requiring easy copying of
audio, video, or Data DVD/CD/BDs. The 2-line 20 character LCD display panel provides the user
with status of the duplication process, the type of process being run, master size, and other useful
information.
Applications suited for the BD Pro include Pro Audio, Multimedia, Government / Education,
Software Development, Medical Imaging, and Data Interchange.
Unpacking your system
When unpacking your duplicator, confirm the following items are included:
•BD Pro duplicator
•Power cable
•Manual
•DVD-R disc
•USB cable
•NetConnect software Installation Disc
If any of these items are missing, please contact Microboards Technology Technical Support.
IMPORTANT: Please keep all the packing for your BD Pro duplicator. If your unit ever needs to
be sent in for service, it must be returned in the original packing or the warranty will be voided.
Installation
•Connect the supplied power cable to the BD Pro duplicator and plug in to a protected
power outlet strip or UPS power supply.
Note for Installation:
1) Please verify that the voltage switch above the power connection is set correctly for
your local power specifications.
2) The socket outlet should be installed near the equipment and be easily accessible.
3) Do not block cooling fans.
•Turn on power to the duplicator.
•The system will go through initialization and then display: 1. Copy.
•Install the NetConnect application and drivers on any PC that may be accessing the hard
drive in the duplicator. These are necessary for your PC to recognize the duplicator hard
drive’s format.
•For USB Mode, connect to a PC via an unoccupied USB port. To access the drive, the
External Connection mode must be turned ON in the Setup Menu (See page 17).
•The system is now ready to use.

Microboards Technology, LLC
6
The LCD Control Panel
The LCD Control Panel shown above has a two-line, 20 character LCD display to provide user
feedback. Eight push buttons control the operation of the Microboards BD Pro Series duplicators.
The functions for these buttons are shown in Table 1-1.
Control Name Function
▲Up Scroll up through the menu or list.
▼Down Scroll down through the menu or list.
ENT ENT or
OK Execute the function. Also called OK in the Menus.
ESC ESC Go back to the previous function.
Copy Quick key to make a copy. Pressing this key takes you directly to the Copy
menu.
Speed Quick key to access the Burn Speed selections. Pressing this key takes you
directly to the Select Burn Speed menu.
CD+G
Quick key to change the CD+G Support setting.
As BluRay Recorders do not support duplication of the CD+G format, this
setting is not used on the BD Pro Series.
Ext
Connect
Quick key to change the External Connection setting. Pressing this key takes
you directly to the External Connection menu item within the Setup menu.
Table 1-1: Front Panel Controls

BD Pro Series
7
Hardware Description
The BD Pro system consists of 4 to 10 BD Recorders (based on model), USB Connection, and
Controller module. The BD Pro Series also includes an internal Hard Drive for Master Image
Storage.
The USB Connection is located on the back of the BD Pro.
The master discs always go into the top recorder drive.
The blank media will always go into the remaining recorder drives.
The power switch and power LED are also located on the front of the BD Pro duplicator.
The LCD display will show the different menu selections and also information pertaining to the
recording process. Here is a typical example of what is displayed during the COPY process:
BD Recorder Drives
Controller Interface
Power Switch and
LED
BD PROV3-04
Copying
71%
15 3157M
Displays the function being performed,
such as Copying or Testing.
Shows the total size of the
master being copied.
Displays the number of discs
successfully burned with the
current master.
Shows the amount of data burned
to the discs currently in the
recorders.
4447M
Shows the percentage
completed for this
action.

Microboards Technology, LLC
8
Main Menu
This section provides an overview of the menu options. These menu options are explained in
detail in the Using the BD Pro Series Duplicator section starting on page 10.
Copy
Use the Copy menu to make CD and DVD copies. Before you start a copy, make sure
you have selected the correct Master Source.
Test
Use the Test menu to simulate the copy process. With simulation, write once recordable
discs such as DVD-R, or CDR will be reusable.
Note: DVD+R and BD recordable media are not compatible with simulation mode. If
you try to simulate with these media types, you will encounter failure messages.
If you are using Rewritable discs as your blank media during the simulation, the
content on those discs will be permanently erased.
Compare
Use the Compare function to perform a bit-by-bit comparison between the content of your
master disc and the contents of all discs it copied. This ensures that all of your copies are
identical to original master disc.
Note: The bit-by-bit comparison will only apply on all DVDs and Data CDs. The
readability check will be applied for other formats like Audio CDs, CD+G, and
Video CDs discs due to their lack of error correction mechanisms.
Test + Copy
Use the Test + Copy menu option to simulate the copying process initially. Then, the
duplicator performs the copy process on the blank disc(s) that passed the simulation.
Copy + Compare
Use the Copy + Compare menu option to make 100% reliable copies. After the copy
process is done, the duplicator automatically compares the copies from the content of
your original master disc.
Select Burn Speed
Use the Select Burn Speed menu option to adjust the duplication speed for the various
blank disc formats. For additional information, see Select Burn Speed on page 12.
Select Source
Use the Select Source menu option to specify which drive is being used as the master
drive. You should always select the DVD-ROM drive or the hard drive (if available) as
the source unless there is a specific need to use one of the recorders as the master
drive.
Erase
Use the Erase menu to erase your Rewritable discs.
Hard Drive Setup
This menu item will not appear if the External Connection setting is ON.
Use the Hard Drive Setup menu to access the Hard Drive functions. You can scroll
between the various options using the ▲Up or ▼Down button. For information on the
Hard Drive Setup functions, please see page 12.
1. Select Partition
2. Load Partition
3. Rename Partition
4. Delete Partition
5. Partition Info
6. Select Loading Drive
7. Format Hard Drive
Mix Audio Tracks
Use the Mix Audio Tracks menu option to select and burn specific tracks from Audio CDs
onto your blank CDs. This function will not operate if CD+G Support is ON (page 19).

BD Pro Series
9
Setup
Use the Setup menu options to control how the Duplicator operates. You can scroll
between the various options using the ▲Up or ▼Down button.
1. Language
2. Auto Start
3. Read Error Skip
4. CD Writing Mode
5. Max Audio, VCD & CDG Speed
6. Buzzer
7. Startup Menu
8. Screen Saver
9. Duplication Mode
10. Counter
11. DVD+R High Compatibility Mode
12. ISRC
13. Disable Drives
14. External Connection
15. CD+G Support (Note: BluRay Recorders do not support the CD+G format)
16. Overburn
Utilities
The Utilities menu includes a number of functions that are not related to the actual
duplication process.
1. Disc Info
2. Prescan
3. System Info
4. Device Info
5. Load Default
6. Update Firmware
7. Save
Manage Accounts
The Manage Accounts menu includes optional User functions that allow you to limit
access to the duplicator.
1. View User
2. Create User
3. Edit User Info
4. Delete User
5. Password on Bootup
AutoCopy
The AutoCopy function simplifies the copy process. After the initial round of blanks is
burned, you only need to load the drives again and close them. Once the drives detect
the new blank media in the drives, duplication begins without you having to touch the
control panel.
Shutdown
Use this menu option to save any setting changes you may have made and turn off your
system. Once you see the “Ready to Power Off” message, you can safely turn off the
machine using the power switch.
Turning off your duplicator without performing this function increases the risk of damaging
it. Additionally, if you made any setting changes, those changes may not be saved if you
simply turn off the power to the duplicator.

Microboards Technology, LLC
10
Counter:
Specify Counter
Specify Counter:
[0 ] OK?
Counter:
No Counter
Microboards B.30
1. Copy
Counter:
No Counter
Preparing... 4063MB
3 Discs Detected, Go?
Setting Counters
The BD Pro Series give you the option to set a counter so that the machine can keep track of the
number of copies made. Follow these steps when you see a Counter Selection Menu:
The Counter Selection Menu lets you set how many copies you want to
make for your project. The Counter Selection feature tells the duplicator
to count the number of successful copies you have made and stop the
job when the desired number of copies has been reached.
You can select “No Counter” if you prefer to copy continuously with no interruption. (It will still
count the number of copies, but it will not notify you when to stop.) To select the “No Counter”,
simply press the ENT button when you see the screen above.
Or, you can select “Specify Counter” between 1 to 9999 by pressing the ▲Up or ▼Down button
to go to the Specify Counter menu:
Press the ENT button to select this option. You will see the next
Specify Counter menu.
To specify the number of copies for your project, you need to input a
four-digit number. If you need to specify a number that is less than
four digits, fill the leading spaces with zeros. Examples are “0234”
(two hundred and thirty four), or “0010” (ten).
To enter the number, you need to use the ▲Up or ▼Down button to select the number for each
digit and use the ENT button or the ESC button to move the cursor position right or left. Once
you've finished, move the cursor to “OK” and press the ENT button.
To input the desired quantity, do the following:
¾Make sure the cursor is located at the first position (First blinking position):
¾Press the ▼Down button repeatedly until “0” is displayed.
¾Press the ENT button once to move the cursor to the next position.
¾Press the ▼Down button repeatedly until “0” is displayed.
¾Press the ENT button once to move the cursor to the next position.
¾Press the ▼Down button repeatedly until “2” is displayed.
¾Press the ENT button once to move the cursor to the next position.
¾Press the ▼Down button repeatedly until “1” is displayed.
¾With “0021” displayed, press the ENT button once and the cursor moves to “OK”.
¾Press the ENT button once more to submit your counter value and start duplication.
Using the BD Pro Series Duplicator
Copy
This process will copy your master disc on to several blank discs
simultaneously.
Use the ▼▲ buttons to navigate to the 1. Copy Menu.
Insert your blank discs in the recorder drives. If your Counter
setting is ON, you will see the Counter Selection menu:
Follow the instructions shown in Setting Counters (above) to continue. Once the counters have
been set, press the ENT button to confirm.
As the blank discs are recognized, the number detected will
increase. Press the ENT button to start the duplication. If you
have Autostart set, duplication will begin either once all recorders
have been found to contain blank media or until the Autostart time interval passes.

BD Pro Series
11
Microboards B.30
3. Compare
Compare OK: 7
Fail: 0 Diff: 0
Src:01 CD-RW
Total: 15.2MB
Tgt: 00 CD-RW
Identical
Microboards B.30
2. Test
After a few seconds of processing time, one of the following Copy Progress screens will appear.
Copying... 4063MB
0/21 12% 488MB or: Copying... 4063MB 0 12% 488MB
¾“4063MB” indicates the
capacity of the master
disc.
¾“0/21” indicates you have
a project size of 21
copies and you have
made 0 copies so far.
¾“12%” indicates the
current progress of the
duplication.
¾488MB indicates the
amount of data burned
so far.
¾“4063MB” indicates the
capacity of the master
disc.
¾“0” indicates you have
made 0 copies so far.
¾“12%” indicates the
current progress of the
duplication.
¾488MB indicates the
amount of data burned so
far.
Note: It is normal to see the progress indicator stay at 0%-10% and 100% for
approximately 30 seconds for CD duplication and up to one minute for DVD duplication.
That is caused by the initializing and finalizing stages.
Once the duplication run is completed, the recorder drives will
eject and the number of successful and failed discs will be
displayed.
At this point, you can add more blank discs to the recorder drives and repeat the process. If you
have the Counter set, only the number of discs selected will be burned.
If you need to switch master discs and have the duplicator in Load and Copy or Prompt mode
(see Duplication Mode, page 16), you must press ESC at this point to return to the 1. Copy
menu or the prior master loaded will be burned to your new blank media.
Test
The Test function is useful to determine if your master disc can be
successfully read.
This process is identical to the Copy process, with the one exception being that the discs will not
be burned to if the media supports test mode.
DVD+R and BD media do not support test mode.
Running rewritable media in Test mode will cause any data on the discs to be erased.
Compare
The Compare function is used to compare the master disc with the
copied discs. The Compare function will only work with Data masters.
If your master disc has audio or video (VCD) on it, the Compare
function will not work.
To use the Compare function, press the ▼▲ buttons until 3. Compare is displayed.
Place your master disc into the top drive and your copied discs into the remaining drives.
Press the ENT button on the controller interface.
The duplicator will now compare the copies to the master disc.
When completed, the display will read:
Press the ▼button and the following screen will appear:
Press the ▼button again and the following screen will appear.
Use the ▼button to scroll through each drive that was used during
the Compare.
Pass 3 Fail 0 ( 3)
Waiting for Blanks

Microboards Technology, LLC
12
Microboards B.30
4. Test+Copy
Microboards B.30
5. Copy+Compare
Microboards B.30
6. Select Burn Speed
Microboards B.30
7. Select Source
Microboards B.30
8. Erase
Test + Copy
The Test + Copy function first simulates the burn to the media
and then burns to the media if the Test simulation is successful.
DVD +R media does not support test mode.
Copy + Compare
The Copy + Compare function first burns to the media and then
runs a comparison of the burned discs to the master disc.
Select Burn Speed
This menu option allows you to change the duplication speed for
each of the duplication job types. Available burn speeds will
vary, depending on the model of the recorder drives installed in
your duplicator. Press the ENT button to change burn speeds.
Since speeds can be set based on media type being used or whether the hard drive is being used
as the source, press the ▼▲ buttons to navigate to the duplication type whose burn speed you
wish to change, then press the ENT button. Use the ▼▲ buttons again to display the burn
speed you would like to choose and press ENT.
When you have changed the burn speed, press ESC to return to the main menu.
Select Source
Use this menu to select which drive will be used as the master
drive, in which you would load your master disc. By default, the
top drive is set as the source.
Press the ENT button to change the source drive. Use the ▼▲ buttons to navigate through the
drives, pressing ENT when the drive you want to use is shown.
It is not recommended that you change the source to anything other than the top drive or the hard
drive unless it is necessary to do so.
If the External Connection is active, the hard drive will not be available and the source
drive will be reassigned to one of the other drives in the duplicator.
Erase
This menu option is used to erase rewritable media placed in the
recorder drives. The Erase function has 2 options:
¾Full Erase: This option erases the entire disc,
destroying all previously written data in the process.
¾Quick Erase: This option erases the index (TOC) of the Rewritable disc, not the data
section. It is much faster than Full Erase. However, the data section is still recoverable.
If you prefer the old content not to be recovered for security purpose, please perform
Full Erase.
Hard Drive Setup
This menu is used to access the Hard Drive functions.
This menu option will not be available if the External Connection setting is On.
If it is not already set so, you will be asked if you want the set the hard drive as the source. Press
the ENT button to set the hard drive as the source and enter the Hard Drive Setup menu.
1. Select Partition
This function is used to select the default partition on the hard drive for duplication.
Use the ▼▲ buttons to move between the available partitions, pressing the ENT
button when the partition you want is displayed. The partition selected will become the
first that is displayed after you press the ENT button when the display reads 1. Copy.

BD Pro Series
13
Microboards B.30
10. Mix Audio Tracks
Load Partition[231GB]
Load- New Partition
2. Load Partition
Use this function when you want to add a new master
disc partition to your hard drive.
After pressing ENT when the display reads 2. Load Partition, you will be asked to verify
that you want to load a partition. Press ENT to continue loading.
Enter in the partition name of up to 14 characters, using the ▼▲ buttons to change the
first character. Press ENT when the character you want is in the cursor position. To
leave a position blank, press ENT when the space is empty.
After entering in all 14 characters, press ENT to highlight OK on the display. If the
name is correct, press ENT. If you need to make changes, press the ESC button until
the cursor is on the character that needs to be changed.
You will be asked to verify the name one last time before the master inserted in the
reader drive is copied to the hard drive. The copy progress will be sown on the display.
Once the master disc is copied to the hard drive, the reader drive will be ejected.
The master under the partition name you entered will now be available for duplication
from the hard drive.
3. Rename Partition
The Rename Partition function allows you to change the name of an existing partition
on the hard drive.
Use the ▼▲ buttons to move through the list of partitions until you get to the partition
you want to rename. Press ENT, then use the ▼, ▲, and ENT buttons as in the Load
Partition function to change the name. Press the ENT button when the cursor is on OK
to save the new partition name.
4. Delete Partition
Use the Delete Partition function to remove a master partition that is no longer in use or
if you need to clear hard drive space for new partitions to be added. Use the ▼▲
buttons to select the partition to delete, then press ENT. You will be asked to confirm
deletion of the selected partition; press ENT if you are sure you want to remove the
partition from the hard drive.
The Delete Partition function cannot be undone.
5. Partition Info
Use the ▼▲ buttons to scroll through the loaded partitions. The type of master used,
size of the data in the partition, and the name will be displayed.
6. Select Loading Drive
By default, the drive selected as the source will be used for transferring a master from
disc to hard drive, but you can use this function to select a different source drive. Use
the ▼▲ buttons to scroll through the available drives to find the drive you want to use.
Press ENT to select the displayed drive.
This will not change the Source Drive in the Main Menu; it will only be used as the
source for loading discs to the hard drive.
7. Format Hard Drive
The Format Hard Drive function will clear all contents from the hard drive. If you want
to delete all partitions from the hard drive, this function is a quicker method than using
the Delete Partition function on each individual partition.
The Format Hard Drive function cannot be undone.
Mix Audio Tracks
If you have the External connection is On, the display will show this menu item as 9, not 10.
You can use the Mix Audio Tracks feature to combine specific
tracks from multiple audio CD masters onto a single disc. Insert
your first master disc and one blank CD, then press ENT when
the display shows Mix Audio Tracks.
The BD Pro Series Duplicator will give you the option of sending the tracks to the hard drive (if
available) or burning directly from CD. Regardless of the method, the track selection process will
be the same.

Microboards Technology, LLC
14
Total: 4 Trk 12m:43s
*Track 6: 3m:56s
Total: 0 Trk 0m:00s
Track 1: 4m:24s
Microboards B.30
11. Setup
Microboards B.30
12. Utilities
Microboards B.30
13. Manage Accounts
After the master audio disc is analyzed and any blank discs
recognized, you will be able to select tracks from the master by
using the ▼▲ buttons to navigate through the tracks and
pressing ENT to select the tracks you want to burn.
The top line of the display will show the number of tracks
currently selected and the total time of selected tracks. The
bottom line of the display will show the track number and time for
the current track.
If a track is selected for the audio mix, the bottom line will begin with an asterisk ( * ). In the
example to the right, 4 tracks have been selected, totaling 12 minutes 43 seconds; track 6 is 3
minutes and 56 seconds in length and has been selected for burning, as indicated by the asterisk.
When you use the ▼▲ buttons to go past the last track, you will be asked if you are done. Press
ENT to burn the selected tracks from the current master to the blank media, or ESC to add more
tracks from the same master. If you want to add tracks from another audio CD and are not
sending the tracks to the hard drive, you will have to burn the selected tracks from the current
master before doing so.
After pressing ENT to burn the tracks, or if you are using the hard drive to store the tracks, you
will be asked if you are finished mixing. If you are, press ENT and the burned discs will be
finalized. If you want to add tracks from another audio CD, press the ▼button for the option to
insert the next master. Follow the same procedure to select and burn tracks for each master
disc.
If you are using the hard drive to store the selected tracks, the discs will not be burned until you
have specified that you are done mixing.
The disc must be finalized before it will be playable. If you are burning the tracks from the hard
drive, this will occur automatically. If you are mixing tracks directly from CD, you will have to
finalize the disc as the last step.
Please note that the Mix Audio Tracks function cannot be performed if you have CD+G Support
ON and the External Connection ON when using the BD Pro Series.
Setup
If you have the External connection is On, the display will show
this menu item as 10, not 11.
The Setup menu includes many functions that affect the operation of the BD Pro Duplicator.
Please see page 16 for more information on the Setup menu options.
Utilities
If you have the External connection is On, the display will show
this menu item as 11, not 12.
The Utilities menu provides you with hardware information and a few maintenance functions.
Please see page 20 for more information on the Utilities menu.
Manage Accounts
If you have the External connection is On, the display will show
this menu item as 12, not 13.
The Manage Accounts menu includes optional User functions that allow you to limit access to the
duplicator.
You must either log in as the Admin user or have the Password on Bootup setting as
NO if you want to access the Manage Accounts menu.
You will be asked for the password when you enter the Manage Accounts menu. The default
password is 0000, which should be changed if you plan on using the user account security
features. Keep a record of the Admin account password.

BD Pro Series
15
Microboards B.30
14. AutoCopy
Microboards B.30
15. Shutdown
1. View User
This function allows to you see the list of available user accounts. Use the ▼▲
buttons to scroll through the user list.
2. Create User
Use the Create User function to add a new user account.
You will first be asked to enter in the new user name. Use the ▼▲ buttons to select
the first character, then press ENT to move to the next, or ESC to move to the prior
character. You can enter in up to 14 characters. After the 14th character is entered,
press ENT when the cursor is on OK.
Next, enter the user’s password. The password is limited to numerals, and will be 4
digits long. Again, use the ▼▲ buttons to change the number of the current digit,
pressing ENT when the number is correct. After the 4th digit is entered, press ENT
when the cursor is on OK. The display will briefly show that the user has been
added.
3. Edit User Info
Use the Edit User Info menu to change an existing user’s name or password.
You will first be able to change the user’s name. Use the ENT or ESC buttons to
move right or left in the user’s name and the ▼▲ buttons to change the highlighted
character and press ENT to accept the character. When all changes are complete,
move the cursor to OK and press ENT.
The password can be modified next using the same method. When the new
password is entered, press ENT to move the cursor to OK and press ENT one more
time to save the changes you have made. The display will briefly show that the user
information has been changed before returning to the menu.
4. Delete User
The Delete User is used to remove users account from the list. The Admin user
account cannot be deleted.
Use the ▼▲ buttons to scroll through the list of existing users. When the display is
showing the user you want to remove, press the ENT button. You will be asked to
verify that you want to remove the user; press ENT if you do, or ESC if it is not the
correct user to delete. The display will briefly show that the selected user has been
deleted.
5. Password on Bootup
To use the Managed Accounts Users to limit access to the duplicator, you must turn
the Password on Bootup setting to YES. This will take effect the next time the
duplicator is turned on.
You must use either the Save function in the Utilities menu or the Shutdown function prior
to turning the duplicator off, or changes you have made to the accounts may not be saved!
AutoCopy
If you have the External connection is On, the display will show
this menu item as 13, not 14.
The AutoCopy function simplifies the copy process. After the initial round of blanks is burned,
you only need to load the drives again and close them. Once the drives detect the new blank
media in the drives, duplication begins without you having to touch the control panel (Auto Start
must be set to Auto or Full).
Shutdown
If you have the External connection is On, the display will show
this menu item as 14, not 15.
When turning off your BD Pro Duplicator, it is highly recommended that you do so using the
Shutdown menu option. Not only does this function save any system settings that you may have
changed in the Setup menu, it also shuts down the duplicator components in a safe way.
When the display reads Ready to Power OFF after selecting the Shutdown function, you can use
the power switch on the front.

Microboards Technology, LLC
16
The Setup Menu
The Setup menu includes many settings the user can select to customize the use of the BD Pro
duplicator. A description of the options in the setup menu follows.
Note: You must use either the Shutdown menu or manually run the Save function from the
Utilities menu, or any changes you make to the Setup Menu settings will be lost
when you turn off your duplicator.
Language
The BD Pro duplicator has multiple language options, with English being the default setting.
Auto Start
The Auto Start feature is used to automatically start recording, once the master disc and blank
discs are inserted into the drives. The Auto Start feature applies to Copy, Test, Test + Copy,
Copy + Compare, and Erase.
There are 3 options for this setting, Auto, Full, and Off.
•Auto: Starts the duplication process when all detect recordable media or 30 seconds has
passed after the first blank disc is recognized, allowing you to leave some recorders
empty while still using the Auto Start feature
•Full: Only starts the duplication when all drives report media as being present.
•Off: You must press the ENT button to begin the duplication process, regardless of the
number of discs loaded.
Read Error Skip
With Read Error Skip OFF, the duplicator will halt any job when the reader encounters an error on
your master disc. By changing this setting to ON, duplication will continue after finding a read
error on the master. Please note that this does not fix the error, and may result in unusable
discs.
It is strongly recommended that you do not change this setting from the default value of OFF.
CD Writing Mode
This setting allows you to change the CD writing mode between the 2 options, Disc at Once and
Track at Once. The default setting is Disc at Once, which should be used unless you have a
specific need to change the mode.
Max Audio, VCD, CDG Speed
Audio CD, Video CD and CD+G disc formats do not have internal error checking capabilities, so
duplicating at high speeds may cause more instances of errors on the copies. This setting allows
you to reduce the burn speed of these specific types of discs without lowering the burn speed of
Data CD discs.
Buzzer
The Buzzer function will turn the beeper on the controller ON or OFF. Using the default of ON, a
beep is heard when a button is pressed or when any job completes.
Startup Menu
Allows you to specify what the default menu item will be when the BD Pro is turned on.
Screen Saver
Use this setting to enable or disable the Screen Saver feature. When this is enabled, a screen
saver is displayed whenever your duplicator has been idle for a set period of time.
Duplication Mode
This menu option cannot be changed if the External Connection setting is On.
There are 3 options available in the Duplication Mode menu: Load and Copy, Prompt, and On
the Fly. These options do not apply if the hard drive is selected as the source.

BD Pro Series
17
The Load and Copy setting will load the master to the hard drive during the first burn cycle;
subsequent burns without leaving Copy mode or changing the master disc will use the hard drive
image as the source for added stability.
If you need to change masters when the Duplication Mode is set to Load and Copy, you must
return to the main 1. Copy menu.
The Prompt setting will ask you to specify Load and Copy or On the Fly when the Copy button is
pressed.
The On the Fly setting will use the loaded master disc in the reader drive as the source at all
times.
Counter
Use the Counter menu to enable or disable the Counter feature. The counter tells you how many
discs have copied and how many discs are left to go during the duplication process stopping the
job once the desired number of copies has been made.
DVD+R High Compatibility Mode
This feature allows you to turn the DVD+R High Compatibility Mode feature ON or OFF. The
purpose of this feature is to increase the compatibility of DVD+R media with a broader range of
DVD Video players.
ISRC
This option will allow you to enable/disable copying the ISRC code of an Audio CD. ISRC is the
serial number of the audio track that uniquely identifies the song in that audio track. This ISRC
code is commonly found in commercial Audio CDs and rarely seen on home made Audio CDs. By
enabling this feature, the duplication performance will be lowered.
Disable Drives
Use this utility to allow the system to disable certain drives/trays when certain drives/trays are
producing high failure rates.
External Connection
The BD Pro Series Duplicators include a USB connection that allows you to use the hard drive as
an external drive connected to your PC. The BD Pro Series also includes an optional Ethernet
connection.
Use this setting to enable one drive in the duplicator to be used as an external drive connected to
your PC through a USB 2.0 connection or with the optional Ethernet connection.
Select the Setup menu and use the ▼▲ buttons and press the ENT button the display reads
External Connection. If the display indicates that the connection is OFF, use either arrow key to
change the setting to ON, then press ENT to save the setting. The duplicator will be briefly
unresponsive as the hard drive is released from duplication mode. Press ESC to leave the Setup
menu.
Please note that while the External Connection setting is ON, the connected drive will be
unavailable to the duplicator.
Overburn
This feature allows you to turn the ability to use the overburn area ON or OFF. Only CD-RW and
BD-RE burning will be affected by this setting.
Overburning is the process of recording data past the normal capacity limit. Many disc
manufacturers extend a recordable disc to leave a small margin of extra data surface at the outer
edge.
Turning this feature ON allows rewritable media to be burned out to the full capacity, using the
otherwise reserved areas of the media for data storage.
It is recommended that this setting be left OFF unless it is absolutely necessary for your
masters to copy to your blank media, as only the reported normal capacity of the media
can be guaranteed. There may be variations in the total available capacity between
individual discs that can result in inconsistent burn success.

Microboards Technology, LLC
18
USB Connection
When using the BD Pro Series models, the external connection is to the hard drive in the
duplicator, allowing you to create or copy ISO disc images directly from your PC into the
Duplicator/dup directory on the BD Pro hard drive. ISO images copied to that location will be
available as hard drive partitions that can be selected as the duplication source once the External
Connection setting is OFF. No other image format is supported.
To connect the drive directly to your PC using the USB connection, plug the flat end of
the USB cable to your PC and the square end to the connection on the back of the
duplicator, shown to the right.
Disconnecting the Hard Drive, USB
1. Left-click the Remove Hardware icon in the tool tray in the right corner of your desktop.
The icon will appear either as a green arrow pointing left or a USB plug with a green
check mark on the right, depending on your Operating System.
2. All hardware that can be
disconnected will be listed. Left-
click the USB Mass Storage
Device with the same Drive
letter as that which appeared as
the Duplicator drive in Windows
Explorer.
3. When the message to the right appears, you can turn
the External Connection OFF using the interface on
the Pro Series Duplicator.
If you receive a warning stating that the drive cannot
be disconnected, check that you do not have the drive open in Windows Explorer. This
will keep the drive from being disconnected. Simply close Windows Explorer and attempt
the hardware removal again.
4. The .iso files you copied to the Duplicator\dup directory will now be available on the
hard drive as stored images. Select the Hard Drive as the source and select the correct
file name from the 1. Copy menu.
If you turn the External Connection OFF on the BD Pro without performing this process,
the data you placed on the hard drive may be deleted.
The information on shutting off the External Connection correctly has been included as a quick
guide in the Starter Kit. It is recommended that you keep this guide available as a reference
when using the Premium Pro Series hard drive through the external connection.
Ethernet Connection (optional)
The optional Ethernet Connection allows you to connect the internal hard drive of your BD Pro
Series to your network. Using the supplied NetConnect software, you can connect to the drive
from any PC running the NetConnect application, allowing you to place .iso image files directly
onto the hard drive for use as a master image on the BD Pro.
For the External Connection to function through the Network, it
must be assigned an IP address. If your network uses DHCP to
assign IP addresses, this will occur automatically when the
Network Duplicator software is launched.
If your network does not use DCHP, you will need to assign the
duplicator a static IP address.
1. Select Server Setting from the System menu.
2. Remove the check from the DHCP setting to enable the
Static IP Address and Subnet settings.
3. Enter the static IP address and Subnet settings.
4. Click the Set button.
5. Once the IP address and Subnet mask are recognized,
the device will be available for connections.

BD Pro Series
19
This will only need to be done the first time the Ethernet connection is used.
With the BD Pro External Connection turned ON and the IP settings in place, the application will
show your available network device.
If you have more than one BD Pro available using the Ethernet connection, each available device
will be shown.
Highlight the line with the green Ready icon and click the Connect
button.
The icon will change to orange to indicate that the connection has
been made. The hard drive will now be accessible on your PC
through Windows Explorer as a new hard drive named Duplicator.
Your .iso image files can either be placed in the Duplicator/dup
directory using a simple copy and paste in Windows Explorer, or you
can create your .iso image file directly in that location.
Other icon colors:
•A red icon indicates that the device is on-line, but that it is
currently connected to another PC.
•A blue icon indicates that the IP address is connected to the
network but is not accessible.
•A red X in place of the icon indicates that the device is not
connected to the network.
Disconnecting the Hard Drive, Ethernet Connection:
When you are ready to return control of the hard drive to the BD Pro, or if you need to allow
another PC to access the hard drive, click the Disconnect button in the NetConnect application
before turning OFF the external connection on the BD Pro Duplicator. The Network Duplication
Control software can be shut down at that time and the files will be accessible on the duplicator.
Note on Turning Off the External Connection
Regardless of the type of connection, if you turn the External Connection off without performing
the correct disconnection process based on either USB or optional Ethernet connection, the data
you placed on the hard drive may be deleted.
You should never turn the External Connection setting to OFF while data is being transferred to
the connected drive. You do not need to disconnect the external cable.
The information on shutting off the External Connection correctly has been included as a quick
guide in the Starter Kit. It is recommended that you keep this guide available as a reference
when using the BD Pro Series hard drive through the external connection.
CD+G Support
This feature is not used in the BD Pro Series, as BluRay Recorders do not support duplication of
the CD+G format.
Remember, you must use the Shutdown menu or manually Save
the settings under the Utilities menu if you want any changes
you have made to remain after the Duplicator is shut down!

Microboards Technology, LLC
20
The Utilities Menu
A description of the options in the Utilities menu follows. Use the ▼▲ buttons to scroll through
the menu, pressing the ENT button when the display shows the function you want to perform.
Disc Info
The Disc Info function will display the information regarding the blank recordable media you have
loaded in the recorders. The media format, capacity, manufacture ID, and certified writing speed
of the media will be displayed.
Information regarding any master disc loaded into the reader drive will also be displayed.
Load your media into the drives before pressing ENT when the display shows Disc Info. Each
drive will be checked to see if media is present. If all drives are not filled, you will be shown the
number of discs detected and be prompted to press the ENT again.
Use the ▼▲ buttons to scroll through the drives in which media has been detected.
Prescan
The Prescan function is used to verify the readability of the master disc by scanning for bad
sectors on the master. Performing the Prescan on your masters before duplicating will help
reduce the number of duplication failures caused by a master that contains uncorrectable errors.
You should load your master into the source drive prior to pressing the ENT button when the
display shows Prescan. Your master will be scanned, with the results being displayed when the
analysis is complete.
If the results show that the master disc Failed, you should not attempt to use that master as a
source disc.
System Info
The System Info menu selection displays the model and firmware versions of the installed
controller. Use the ▼▲ buttons to scroll through the system information.
Device Info
The Device Info menu selection displays the model and firmware versions of the drives installed
in your BD Pro Duplicator. Use the ▼▲ buttons to scroll through the device information.
Load Default
This option restores all Setup and Advanced Setup options to the default settings, as well as the
default Burn Speed and the selected Source drive settings.
Update Firmware
Use the Update Firmware menu option to update the programming on your Duplicator. To update
the firmware, you will need to have the correct firmware file burned to a CD.
Please note that “drag-and-drop” burn methods such as the Windows XP burn utility generally will
not be recognized as valid as the disc format they create is not recognizable by the duplicator.
Use a disc burning application such as the Zulu2 Disc Burning application provided with your BD
Pro to burn the Update files to a CD.
Firmware Updates should only be performed after contacting Technical Support to ensure
that you are attempting to install the correct firmware for your duplicator.
Save
This function will save any system settings that you have changed since the last time the
duplicator was booted. This function is part of the process that occurs when you run the
Shutdown process from the Shutdown menu.