Minicom 0SU52016 User manual

International HQ
Jerusalem, Israel
Tel: + 972 2 651 8593
[e-mail]
North American HQ
Linden,New Jersey
Tel: + 1 908 4862100
[e-mail]
German Europe
Zurich, Switzerland
Tel: + 41 1 455 6220
[e-mail]
Italy
Rome
Tel: + 39 06 8209 7902
[e-mail]
Web site - www.minicom.com Customer service - [e-mail]
V1.54/03
Phantom MXII Operating Guide

Introduction
1-1
Chapter 1: Introduction
The Phantom system from Minicom is a CAT5 based Distributed KVM Switching system for server
management. Connect up to 63 computers in the Phantom system. The system can be managed and controlled by
1 or 2 users.
The Phantom MX II system components
The Phantom MX II system consists of:
• 2 Management units
• Remote units
• Cables and accessories – explained in the Installation guide
• Marketing & Documentation CD – includes Application software
Management units
The 2 Management units are the MX II and the Universal Phantom Manager (UPM)
Remote units
The Remote units are Micro-sized external boxes called Specters.
There are a number of Specter types as follows:
• For PS/2 interface computers – Specter II PS/2
• For SUN computers – Specter II SUN
• For RS232 controllable devices – Specter II RS232
• For computers with USB interfaces– Specter II USB
Compatibility
The Phantom system is compatible with:
• IBM compatible, Silicon Graphics, SUN and Alpha computers
• VGA, SVGA, or XGA video standards
• All major computer and server manufacturers
• IntelliMouse™, Logitech WheelMouse, and PS/2 mice
• Microsoft DOS, Windows 3.1, 95, 98, 2000, NT4, ME, and XP. Novel, Linux, SGI, BeOS, HP UX Alpha UNIX, Open
VMS
• PS/2, SUN, RS232, USB interfaces

The Phantom configuration
1-2
Features of the Phantom system
• Control and monitor mixed, multi-platform server environments of up to 63 remote computers from 2 Manager
positions
• Advanced On Screen Display management (including multi-layer security), and BIOS level access
• A total distance of up to 110m/360ft between the Manager computer and the last connected Remote computer
• Pure hardware solution. No drivers. No IRQs.
The Phantom configuration
Figure 1-1 illustrates the Phantom configuration for the MX II and UPM (without optional computers) and
Specter II PS/2 models.
Link
Active Link
Activ e
Link
Active
CAT5 System Cable CAT5 System Cable
First Remote
Computer
Remote
Computer
Last Remote
Computer
Specter Specter Specter
SD
P50
www.minicom. com
USER COMPUTER
SYSTEM SERVICE
85-265VAC 50/60 Hz
2nd USE R
POWER INOUT
www.minicom.com
USER COMPUTER
SERVICEPOWER
85-265VAC50/60Hz
UPM
MXII
CAT5 System Cable
CAT5 System Cable
SD
P50
Figure 1-1 The Phantom Specter configuration with the MX II & UPM
OSD Technology
The Phantom system superimposes a menu on the Manager position computer screens. This On-Screen-Display
(OSD) consists of three sections. From the OSD, you activate various functions discussed later in this Operating
guide.

The OSD functions
2-1
Chapter 2: The OSD functions
The Phantom system is controlled and monitored through On-Screen-Displays (OSD) on the MX II and UPM
Manager screens. You can also use Minicom’s RS232 Control software or equivalent software. The Control
software is discussed in chapter 4. The OSD contains a number of different windows that are accessed using
Hot-keys. Each window has its own special function.
Displaying the OSD
To display the OSD:
Press Shift, Shift. The Select Computer window appears. See Figure 2-1.
Pressing keyboard hotkeys
Note! For all keyboard hotkey sequences mentioned in this guide – press the first key, release and then
press the next key.
Note! When the MX II or UPM are not connected to a local computer the OSD appears automatically.
Instructions
and
Hot-keys
Computers
Name
Figure 2-1 The Select Computer window
The OSD is divided into three sections. These are:
• Name
• Computers
• Instructions and Hot-key guide
The Computers section
The Computers section displays the computers in groups of eight.
Navigate between the groups with the Page Up and Page Down Arrow keys.
In this section you select computers - discussed below.
Line Color codes
Each computer line can be one of three colors as follows:
Yellow Connected and switched on computer.
Black Connected and switched on computer currently being accessed by the other Manager.This is
subject to a Timeout period. Meaning that after a 60 second (default) period of non-use the line
turns to yellow.
Blue Unconnected or switched off computer.

The hotkey functions
2-2
Selecting a Computer
To select a computer:
1. Navigate to the desired computer with the Up and Down Arrow keys.
Or
Type the computer number. It will appear in the “SELECT COMPUTER” line. See Figure 2-1.
2. Press Enter. The selected computer’s screen replaces the Manager’s screen. A Confirmation label appears
showing which computer is accessed. See Figure 2-2.
Figure 2-2 The Confirmation label
Control and monitor the computer from the Manager KVM position. Note! After 60 seconds of non-use the
keyboard and mouse are disabled and a Timeout label appears. See Figure 2-3.
Figure 2-3 The Timeout label
To re-enter the system press Esc.
When trying to select a black colored computer line, (computer currently accessed by the other Manager) you
can view the screen but not gain control. Also a “BUSY” label appears. However, once the other Manager’s
Timeout period activates the “BUSY” label is replaced by a “FREE” label and you can gain control. To gain
control press Esc.
To return to the OSD after accessing a computer:
Press Shift, Shift.
To return to the Manager computer screen:
Press Shift, Esc.
To return to the previously accessed computer screen:
Press Shift, Tab.
The hotkey functions
The OSD hotkey functions are briefly outlined in the table below.
Hotkey Function
F1 Move label identifying the current selected computer to anywhere on the screen
F2 Opens Edit window to edit text – change computer names etc.
F3 Opens Setup window to set parameters – scan times etc.
F4 Activate scan
F5 Image tuning
F6 Autoskip – during a scan skip inactive computers
F7 Opens Password window to activate password protection – explained in chapter 3
F8 Keyboard language
F9 Change the display hotkey
F10 Firmware upgrade/ Numbering software access mode – explained in chapters 5&6
F11 Load defaults – explained in chapter 3
F12 Auto-numbering – explained in chapter 3

The OSD functions
2-3
Move Label - F1
Position the Confirmation label – Figure 2-2 above – anywhere on the screen.
To position the label:
1. Navigate to the desired computer using the Up and Down arrow keys.
2. Press F1. The selected screen image and Identification label will appear.
3. Use the arrow keys to move the label to the desired position.
4. Press Esc to save and exit.
Edit Mode window - F2
You can edit text in the Name and Computers sections. This is done in the Edit Mode window.
To display the Edit Mode window:
Press F2. The Edit Mode window with instructions appears, see Figure 2-4.
Instructions
Computers
Name
Figure 2-4 The Edit Mode window
Navigating between sections
To navigate between the Name and Station sections, use the Up and Down Arrow keys.
Editing options
The editing options below apply to all OSD windows in which you can edit characters.
You can either overwrite or erase a character.
To overwrite a character:
1. Navigate to it using the Arrow keys.
2. Type the new character.
To erase a character:
1. Navigate to it using the Arrow keys.
2. Press the Spacebar. The character disappears. A blank space replaces the erased character.

The hotkey functions
2-4
To erase a sequence of characters:
1. Navigate to the first character in the sequence.
2. Press and hold the Spacebar down until you erase the sequence.
Saving changes
To save all editing changes and return to the Select Computer window:
Press Esc.
Editing the Name section
You can substitute the text in the Name section with up to 30 characters in each of the two lines. A space
constitutes a character.
Editing the Computers section
The numbering at the start of each line is unalterable.
You can substitute the text that appears after the number with up to 20 characters per line.
Editing a group of lines
You can edit a group of lines with the same data change.
To edit a group of lines:
1. Navigate to the first line you want to change.
2. Type the desired change.
3. Press End,End. The rest of the column downwards takes on the same change.
The Setup window - F3
You set parameters, and configure settings, in the Setup window.
To display the Setup window:
Press F3. The Setup window with the relevant instructions and hotkeys appears. See Figure 2-5.
Figure 2-5 The Setup window
The Setup window contains 7 columns, as follows:

The OSD functions
2-5
Column Function
Numbers Computer numbers in groups of 8
SCN Scanning time period
DSP Confirmation label display time
KB Keyboard setting, either PS or Unix
MS Mouse type
OUT Timeout period
1-6 Security profiles (Explained in chapter 3)
The SCN (Scan) column
The SCN column shows the length of time in seconds that a remote computer’s screen will appear on the
Management screen during scanning.
The DSP (Display) column
The DSP column shows the length of time in seconds that the remote computer’s Confirmation label appears
on the Management screen.
Changing the SCN and DSP time spans
The SCN and DSP time spans are preset to 030 seconds. You can adjust these times to suit your needs.
To change the time span:
1. Navigate with the Tab or Right and Left Arrow keys to the time span you want to change.
2. Type the desired time span using the numbers above the keyboard letters.
3. Press Esc.
When typing over a group of three digits, the cursor automatically reverts to the first digit once you edit the
third digit.
Changing the time span of a group of computers
You can change the time spans of the SCN and DSP columns from a particular computer downwards.
To change the time span:
1. Navigate to the time span of the first computer you wish to change.
2. Type the desired change.
3. Press End, End. The remainder of the column takes on the same change.
4. Press Esc.

The hotkey functions
2-6
Removing a computer from the scanning sequence
To remove a computer from the scanning sequence:
1. Type 000 in the SCN column.
2. Press Esc.
Constantly displaying the Confirmation label
To constantly display the computer Confirmation label:
1. Type 999 in the DSP column.
2. Press Esc.
The KB column
The KB column shows the keyboard mapping settings. Set the KB mapping for each computer according to its
operating system.
The default KB mode is PS, which is the standard keyboard mapping for Windows and Linux based operating
systems.
For a UNIX operating system using a standard PS/2 keyboard, set the KB mapping as follows:
• U1 forHP UXand SGI
• U2 for Alpha UNIX and Open VMS
To change the KB column from PS to U1 or U2:
1. Navigate to the KB field by using the Tab or Arrow keys.
2. Press the Spacebar. The display interchanges between PS, U1 and U2. Find the desired setting.
3. Press Esc.
The MS column
The Phantom system automatically detects the mouse types, and configures the system accordingly.
Timeout period
The Management keyboard, mouse and screen are automatically disabled after a preset time of non-use. This
Timeout period is set in the OUT column of the Setup window (F3).
By default the OUT column is 060, meaning the Time Out function is set to 60 seconds.
To change the Timeout period:
1. From the Select Computer window press F3. The Setup window appears.
2. Navigate with the Tab or Arrow keys to the OUT column of the desired computer.
3. Type the desired time span (minimum 030 seconds maximum 998 seconds).

The OSD functions
2-7
( For the rest of the column downwards to take on the same change press End,End.)
4. Press Esc.
When Timeout activates, the keyboard and mouse are disabled, and a ‘Timeout’ label appears. See Figure 2-6.
Figure 2-6 The TIMEOUT label
To re-enter the system:
Press Esc.
Scanning Computers – F4
You scan computers from the Select Computer window.
To start scanning:
Press F4. During scanning a Confirmation label appears, showing which Remote computer is presently
displayed. See Figure 2-7.
Figure 2-7 The Scan Confirmation label
Note! The scan will skip any active computer set to 000 in the SCN column.
To stop scanning press F4.
Image tuning - F5
You can tune the image of any remote computer screen from the Select Computer window.
To adjust the screen image:
1. Navigate to the remote computer you wish to adjust.
2. Press F5. The screen image of the selected computer appears, together with the Image Tuning IN label.
See Figure 2-8.
Figure 2-8 The Image Tuning IN label
3. Adjust the image by pressing the Right or Left Arrow keys.
4. When the image is satisfactory, press F5 again, the Image Tuning OUT label appears. See Figure 2-9
Figure 2-9 The Image Tuning OUT label
5. Adjust the image by pressing the Right or Left Arrow keys. When the image is satisfactory, press Esc.