Mitsubishi Electric MELSEC Q Series User manual

MELSEC-Q EtherNet/IP Network Interface Module
User's Manual
-QJ71EIP71
-SW1DNC-EIPUTL-E

A- 1
SAFETY PRECAUTIONS
(Read these precautions before using this product.)
Before using this product, please read this manual and the relevant manuals carefully and pay full attention
to safety to handle the product correctly.
In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".
Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to
serious consequences.
Observe the precautions of both levels because they are important for personal and system safety.
Make sure that the end users read this manual and then keep the manual in a safe place for future
reference.
[Design Precautions]
WARNING
●When connecting a peripheral with the programmable controller CPU or connecting a personal
computer with an intelligent function module to modify data of a running programmable controller,
configure an interlock circuit in the sequence program to ensure that the entire system will always
operate safely.
For other forms of control (such as program modification or operating status change) of a running
programmable controller, read the relevant manuals carefully and ensure that the operation is safe
before proceeding.
Especially, when a remote programmable controller is controlled by an external device, immediate
action cannot be taken if a problem occurs in the programmable controller due to a communication
failure. To prevent this, configure an interlock circuit in the program, and determine corrective actions
to be taken between the external device and CPU module in case of a communication failure.
●Do not write any data to the "system area" in the buffer memory of the intelligent function module.
Also, do not use any "use prohibited" signal as an output signal from the CPU module to the
intelligent function module.
Doing these operations may cause malfunctions to the programmable controller system.
●Provide security measures on user side that prevent unauthorized access from outside via network
as necessary.
WARNING
CAUTION
Indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions,
resulting in minor or moderate injury or property damage.

A- 2
[Installation Precautions]
CAUTION
●Use the programmable controller in an environment that meets the general specifications in the
user's manual for the CPU module used.
Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of the
product.
●To mount the module, while pressing the module mounting lever located in the lower part of the
module, fully insert the module fixing projection(s) into the hole(s) in the base unit and press the
module until it snaps into place.
Incorrect mounting may cause malfunction, failure or drop of the module.
When using the programmable controller in an environment of frequent vibrations, fix the module
with a screw.
Tighten the screws within the specified torque range.
Undertightening can cause drop of the screw, short circuit, or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.
●Shut off the external power supply (all phases) used in the system before mounting or removing the
module.
Failure to do so may result in damage to the product.
●Do not directly touch any conductive parts and electronic components of the module.
Doing so can cause malfunction or failure of the module.

A- 3
[Wiring Precautions]
WARNING
●Shut off the external power supply (all phases) used in the system before wiring.
Failure to do so may result in electric shock or damage to the product.
●Connectors for external devices must be crimped or pressed with the tool specified by the
manufacturer, or must be correctly soldered.
Incomplete connections may cause short circuit, fire, or malfunction.
CAUTION
●Securely connect the connector to the module.
●Place the communication cable or power cable in a duct or clamp it.
If not, dangling cable may swing or inadvertently be pulled, resulting in damage to the module or
cables or malfunction due to poor contact.
●Check the type of the interface to be connected before wiring the modules.
Connecting to a wrong interface or incorrect wiring may cause a fire or failure.
●When disconnecting a communication cable or power cable from the module, do not pull the cable
part.
For the cable with connector, hold the connector part of the cable.
Pulling the cable connected to the module may result in malfunction or damage to the module or
cable.
●Prevent foreign matter such as dust or wire chips from entering the module.
Such foreign matter can cause a fire, failure, or malfunction.
●A protective film is attached to the top of the module to prevent foreign matter, such as wire chips,
from entering the module during wiring.
Do not remove the film during wiring.
Remove it for heat dissipation before system operation.
●Do not install the control lines or communication cables together with the main circuit lines or power
cables.
Keep a distance of 100mm or more between them.
Failure to do so may result in malfunction due to noise.

A- 4
[Startup and Maintenance Precautions]
WARNING
●Do not touch any terminal while power is on.
Doing so will cause electric shock or malfunction.
●Shut off the external power supply (all phases) used in the system before cleaning the module or
retightening the module fixing screws.
Failure to do so may result in electric shock or cause the module to fail or malfunction.
Undertightening can cause drop of the screw, short circuit, or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.
CAUTION
●Before performing online operations (especially, program modification, forced output, and operation
status change) for the running CPU module from the peripheral connected, read relevant manuals
carefully and ensure the safety.
Improper operations may damage machines or cause accidents.
●Do not disassemble or modify the modules.
Doing so may cause failure, malfunction, injury, or a fire.
●Use any radio communication device such as a cellular phone or PHS (Personal Handy-phone
System) more than 25cm (9.85 inches) away in all directions from the programmable controller.
Failure to do so may cause malfunction.
●Shut off the external power supply (all phases) used in the system before mounting or removing the
module.
Failure to do so may cause the module to fail or malfunction.
●After the first use of the product, do not mount/remove the module to/from the base unit more than
50 times (IEC 61131-2 compliant).
Exceeding the limit of 50 times may cause malfunction.
●Do not drop or apply shock to the battery to be installed in the module.
Doing so may damage the battery, causing the battery fluid to leak inside the battery.
If the battery is dropped or any shock is applied to it, dispose of it without using.
●Before handling the module, touch a conducting object such as a grounded metal to discharge the
static electricity from the human body.
Failure to do so may cause the module to fail or malfunction.

A- 5
[Startup and Maintenance Precautions]
[Disposal Precautions]
[Transportation Precautions]
WARNING
●Before performing online operations (especially, program modification, forced output, and operation
status change) for the running CPU module from the peripheral connected, read relevant manuals
carefully and ensure the safety.
Incorrect change or modification may cause system malfunction, damage to the machines, or
accidents.
●Do not write any data to the "system area" in the buffer memory of the intelligent function module.
Also, do not use any "use prohibited" signal as an output signal from the CPU module to the
intelligent function module.
Doing these operations may cause malfunctions to the programmable controller system.
CAUTION
●When disposing of this product, treat it as industrial waste.
When disposing of batteries, separate them from other wastes according to the local regulations.
(For the Battery Directive in EU member states, refer to Appendix 2.)
CAUTION
●When transporting lithium batteries, follow the transportation regulations. (For details of the
regulated models, refer to Appendix 1.)

A- 6
CONDITIONS OF USE FOR THE PRODUCT
(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;
i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major
or serious accident; and
ii) where the backup and fail-safe function are systematically or automatically provided outside of
the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.
(2) The PRODUCT has been designed and manufactured for the purpose of being used in general
industries.
MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT
LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,
WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR
LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR
USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,
OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY
MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.
("Prohibited Application")
Prohibited Applications include, but not limited to, the use of the PRODUCT in;
• Nuclear Power Plants and any other power plants operated by Power companies, and/or any
other cases in which the public could be affected if any problem or fault occurs in the PRODUCT.
• Railway companies or Public service purposes, and/or any other cases in which establishment of
a special quality assurance system is required by the Purchaser or End User.
• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as
Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,
Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or
Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a
significant risk of injury to the public or property.
Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the
PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT
is limited only for the specific applications agreed to by Mitsubishi and provided further that no
special quality assurance or fail-safe, redundant or other safety features which exceed the general
specifications of the PRODUCTs are required. For details, please contact the Mitsubishi
representative in your region.

A- 7
REVISIONS
*The manual number is given on the bottom left on the back cover.
Japanese Manual Version SH-081156-B
©2013 MITSUBISHI ELECTRIC CORPORATION
Print date *Manual number Revision
July 2013 SH(NA)-081157ENG-A First edition
February 2015 SH(NA)-081157ENG-B
Added function
Setting of a tag name with 41 or more characters
Added or modified parts
GENERIC TERMS AND ABBREVIATIONS, Section 3.1, 3.3.1, 3.3.4, 3.3.5, 4.2,
5.2.1, 7.2.1, 7.2.2, 7.2.3, 7.6, 7.9.1, 7.9.2, 7.9.3, 7.9.4, 7.12, 8.3, 9.4.1, Appendix
5
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.
Mitsubishi Electric Corporation cannot be held responsible for any problem involving industrial property rights which may
occur as a result of using the contents noted in this manual.

A- 8
SAFETY PRECAUTIONS .................................................................................................................................A - 1
CONDITIONS OF USE FOR THE PRODUCT..................................................................................................A - 6
REVISIONS.......................................................................................................................................................A - 7
INTRODUCTION...............................................................................................................................................A - 8
CONTENTS ......................................................................................................................................................A - 8
COMPLIANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES...........................................................A - 12
HOW TO READ THIS MANUAL .....................................................................................................................A - 14
HOW TO USE THIS MANUAL........................................................................................................................A - 15
GENERIC TERMS AND ABBREVIATIONS....................................................................................................A - 16
DEFINITIONS OF TERMINOLOGY................................................................................................................A - 17
PACKING LIST ...............................................................................................................................................A - 18
CHAPTER 1 OVERVIEW 1 - 1 to 1 - 7
1.1 Features........................................................................................................................................... 1 - 2
CHAPTER 2 SYSTEM CONFIGURATION 2 - 1 to 2 - 9
2.1 Applicable Systems ......................................................................................................................... 2 - 1
2.2 Network Configuration and Components .........................................................................................2-4
2.2.1 Network configuration ............................................................................................................... 2 - 4
2.2.2 Network components of the EtherNet/IP network..................................................................... 2 - 5
2.3 Operating Environment for Utility Package...................................................................................... 2 - 6
2.4 Checking the Function Version and Serial Number......................................................................... 2 - 8
CHAPTER 3 SPECIFICATIONS 3 - 1 to 3 - 40
3.1 Performance Specifications ............................................................................................................. 3 - 1
3.2 I/O Signals for the QCPU................................................................................................................. 3 - 3
3.2.1 I/O signal list ............................................................................................................................. 3 - 3
3.2.2 Tag communication start request (Y00), Tag communication start process
completion (X00)....................................................................................................................... 3 - 4
3.2.3 PING test execution request (Y02), PING test completion (X02) ............................................. 3 - 8
3.2.4 Flash ROM access request (Y06)/Access completion (X06)/Access error
completion (X07)....................................................................................................................... 3 - 9
3.2.5 TCP/UDP/IP parameter change request (Y08), TCP/UDP/IP parameter change
completion (X08)..................................................................................................................... 3 - 10
INTRODUCTION
Thank you for purchasing the MELSEC-Q series programmable controller.
Before using the equipment, please read this manual carefully to develop full familiarity with the functions and
performance of the Q series programmable controller you have purchased, so as to ensure correct use.
Please forward a copy of this manual to the end user.
CONTENTS