Mitsubishi Electric Q64RD User manual

RTD Input Module
Channel Isolated RTD Input Module
User's Manual
-Q64RD
-Q64RD-G
-GX Configurator-TI (SW1D5C-QTIU-E)

A - 1 A - 1
SAFETY PRECAUTIONS 
(Read these precautions before using this product.)
Before using this product, please read this manual and the relevant manuals carefully and pay full
attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product only. For the safety precautions of
the programmable controller system, refer to the user’s manual for the CPU module used.
In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".
Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to
serious consequences.
Observe the precautions of both levels because they are important for personal and system safety.
Make sure that the end users read this manual and then keep the manual in a safe place for future
reference.
[Design Precautions]
WARNING
Do not write any data to the "system area" of the buffer memory in the intelligent function
module.
Also, do not use any "use prohibited" signals as an output signal from the programmable
controller CPU to the intelligent function module.
Doing so may cause malfunction of the programmable controller system.
CAUTION
Do not install the control lines or communication cables together with the main circuit lines or
power cables.
Keep a distance of 100mm or more between them.
Failure to do so may result in malfunction due to noise.

A - 2 A - 2
[Installation Precautions]
CAUTION
Use the programmable controller in an environment that meets the general specifications in the
user's manual for the CPU module used.
Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of
the product.
To mount the module, while pressing the module mounting lever located in the lower part of the
module, fully insert the module fixing projection(s) into the hole(s) in the base unit and press the
module until it snaps into place.
Incorrect mounting may cause malfunction, failure or drop of the module.
When using the programmable controller in an environment of frequent vibrations, fix the
module with a screw.
Tighten the screws within the specified torque range.
Undertightening can cause drop of the screw, short circuit or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or
malfunction.
Shut off the external power supply (all phases) used in the system before mounting or removing
the module.
Failure to do so may result in damage to the product.
A module can be replaced online (while power is on) on any MELSECNET/H remote I/O station
or in the system where a CPU module supporting the online module change function is used.
Note that there are restrictions on the modules that can be replaced online, and each module
has its predetermined replacement procedure.
For details, refer to the relevant chapter in this manual.
Do not directly touch any conductive and electronic component of the module.
Doing so can cause malfunction or failure of the module.

A - 3 A - 3
[Wiring Precautions]
WARNING
After wiring, attach the included terminal cover to the module before turning it on for operation.
Failure to do so may result in electric shock.
CAUTION
Individually ground the FG terminal of the programmable controller with a ground resistance of
100 or less.
Failure to do so may result in electric shock or malfunction.
Tighten the terminal screws within the specified torque range.
Undertightening can cause short circuit, fire, or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or
malfunction.
Prevent foreign matter such as dust or wire chips from entering the module.
Such foreign matter can cause a fire, failure, or malfunction.
A protective film is attached to the top of the module to prevent foreign matter, such as wire
chips, from entering the module during wiring.
Do not remove the film during wiring.
Remove it for heat dissipation before system operation.
Use applicable solderless terminals and tighten them with the specified torque.
If any solderless spade terminal is used, it may be disconnected when the terminal screw comes
loose, resulting in failure.

A - 4 A - 4
[Startup and Maintenance Precautions]
WARNING
Do not touch any terminal while power is on.
Doing so will cause electric shock or malfunction.
Shut off the external power supply (all phases) used in the system before cleaning the module or
retightening the terminal screws, connector screws, or module fixing screws.
Failure to do so may result in electric shock or cause the module to fail or malfunction.
Undertightening can cause drop of the screw, short circuit or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or
malfunction.
CAUTION
Do not disassemble or modify the modules.
Doing so may cause failure, malfunction, injury, or a fire.
Shut off the external power supply (all phases) used in the system before mounting or removing
the module.
Failure to do so may cause the module to fail or malfunction.
A module can be replaced online (while power is on) on any MELSECNET/H remote I/O station
or in the system where a CPU module supporting the online module change function is used.
Note that there are restrictions on the modules that can be replaced online, and each module
has its predetermined replacement procedure.
For details, refer to the relevant chapter in this manual.
After the first use of the product, do not mount/remove the module to/from the base unit, and the
terminal block to/from the module more than 50 times (IEC 61131-2 compliant).
Exceeding the limit of 50 times may cause malfunction.
Before handling the module, touch a conducting object such as a grounded metal to discharge
the static electricity from the human body.
Failure to do so may cause the module to fail or malfunction.
[Disposal Precaution]
CAUTION
When disposing of this product, treat it as industrial waste.

A - 5 A - 5
CONDITIONS OF USE FOR THE PRODUCT 
(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;
i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or
serious accident; and
ii) where the backup and fail-safe function are systematically or automatically provided outside of the
PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.
(2) The PRODUCT has been designed and manufactured for the purpose of being used in general
industries.
MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED
TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,
PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO
PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT
INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN
MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND
GUIDELINES FOR the PRODUCT.
("Prohibited Application")
Prohibited Applications include, but not limited to, the use of the PRODUCT in;
Nuclear Power Plants and any other power plants operated by Power companies, and/or any other
cases in which the public could be affected if any problem or fault occurs in the PRODUCT.
Railway companies or Public service purposes, and/or any other cases in which establishment of a
special quality assurance system is required by the Purchaser or End User.
Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator
and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for
Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or
Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to
the public or property.
Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the
PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is
limited only for the specific applications agreed to by Mitsubishi and provided further that no special
quality assurance or fail-safe, redundant or other safety features which exceed the general
specifications of the PRODUCTs are required. For details, please contact the Mitsubishi
representative in your region.

A - 6 A - 6
REVISIONS
The manual number is given on the bottom left of the back cover.
Print Date Manual Number Revision
Nov., 2000 SH (NA)-080142-A First printing
Jun., 2001 SH (NA)-080142-B Addition
Section 2.1, 2.2
Correction
Conformation to the EMC Directive and Low Voltage Instruction, About
the Generic Terms and Abbreviations, Product Structure, Section 5.2,
5.2.1, 5.2.2, 5.3.3
Feb., 2002 SH (NA)-080142-C Addition
Section 1.2, Section 3.4.18, 3.4.19, Chapter 7, App 2,3
Partial addition
SAFETY PRECAUTIONS, About the Generic Terms and Abbreviations,
Section 2.1, Section 3.1, 3.2, 3.4.1, Section 4.3, 4.6, Section 5.2.1, 5.2.2,
Section 8.1, 8.2.1
Correction
Section 3.3.2, 3.4.10, 3.4.17, Section 4.2, 4.4.1, Section 5.3.2, 5.5, 5.6.1
Section 6.1.1, 6.2.2, Section 8.2.4,
Feb., 2003 SH (NA)-080142-D Addition
Section 5.6.3, 5.6.4
Correction
SAFETY PRECAUTIONS, Section 1.2, Section 2.1, Section 3.1.1, 3.2,
3.3.1, 3.3.2, 3.4.1, 3.4.3, 3.4.4, 3.4.6, 3.4.7, 3.4.10 to 3.4.19, Section 4.5,
4.6, Section 5.1, 5.2.1, 5.2.2, 5.3.2, 5.4, 5.5, 5.6.1, 5.6.2, Section 6.1,
6.1.1, 6.1.2, 6.2, 6.2.1, 6.2.2, Section 7.3.1, 7.3.3 to 7.3.6, 7.4,
Section 8.1, 8.2, 8.2.5, Appendix 2.1, Appendix 3.1 to 3.3
Sep., 2003 SH(NA)-080142-E Description for new model, Q64RD-G is added.
Addition
Section 3.1.2, 3.4.2, 3.4.5, 3.4.7, 3.4.12, 3.4.13, 3.4.23, 7.4.2, 8.2.5,
8.2.6, Appendix 1.3
Correction
About the Generic Terms and Abbreviations, Product Lineup, Chapter 1,
Section 1.1, 2.1, 2.2, 3.1.1, 3.1.3, 3.2, 3.2.1, 3.3.1, 3.3.2, 3.4.1, 3.4.4,
3.4.15 to 3.4.17, 3.4.21, 3.4.25, 4.3, 4.4.2, 4.5, 4.6, 5.1, 5.2.1, 5.6.1,
5.6.2, 5.6.4, 6.1, Chapter 7, Section 7.3.4, 7.3.6, 7.4.1, 8.1, 8.2.10,
Appendix 1.1, 1.2, 3.2, 3.3, 4
May, 2004 SH(NA)-080142-F Correction
Section 2.2, 3.4.16, 7.1, 7.3.1 to 7.3.6
Oct., 2004 SH (NA)-080142-G Correction
SAFETY PRECAUTIONS, Section 2.1, Section 3.1.1, 3.3, 3.4.1, 3.4.1,
Section 4.1, Section 6.2, 6.2.1

A - 7 A - 7
Print Date Manual Number Revision
Sep., 2005 SH (NA)-080142-H Addition
Section 3.4.22, 3.4.23, Appendix 2.2, Appendix 2.2.1, Appendix 2.2.2
Correction
Conformation to the EMC Directive and Low Voltage Instruction,
Section 1.2, Section 2.1, 2.2, Section 3.1.1, 3.1.2, 3.2, 3.3.1, 3.3.2, 3.4.1,
3.4.2, 3.4.5, 3.4.6, 3.4.7, 3.4.10, 3.4.14, 3.4.20, 3.4.21, Section 5.1,
5.2.2, 5.6.1, 6.1.1, 6.2.1, Section 7.3.1, 7.3.3, 7.3.4, 8.1, 8.2.10,
Appendix 2.1
Feb., 2006 SH(NA)-080142-I Addition
Appendix 3.1
Correction
SAFETY PRECAUTIONS, Section 1.2, Section 2.2, Section 3.2, 3.4.13,
Section 7.3.3, 7.3.5, Appendix 3, INDEX
Section number changed
Appendix 3.1 Appendix 3.2, Appendix 3.2 Appendix 3.3,
Appendix 3.3 Appendix 3.4
Oct., 2006 SH(NA)-080142-J Correction
Section 4.5
Oct., 2007 SH(NA)-080142-K Correction
Section 1.1, Section 1.2, Section 3.1.1, Section 3.2, Section 3.2.2,
Section 3.2.3, Section 3.3.2, Section 3.4.2, Section 3.4.19,
Section 3.4.22, Section 4.3, Section 6.2.1, Section 8.1, Appendix3.1,
Appendix3.2, Appendix3.3
Jan., 2008 SH(NA)-080142-L Correction
SAFETY PRECAUTIONS, CONTENTS, About the Generic Terms and
Abbreviations, Section 2.2, Section 2.3, Section 4.1, Section 5.2.2
May, 2008 SH(NA)-080142-M Correction
SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage
Directives, About the Generic Terms and Abbreviations, Section 2.1,
Section 2.3, Section 3.4.19, Section 4.1, Section 5.2.1, Section 5.2.2,
Section 5.3.1 to 5.3.3, Section 7.1
Sep., 2011 SH(NA)-080142-N Addition
CONDITIONS OF USE FOR THE PRODUCT
Correction
SAFETY PRECAUTIONS, COMPLIANCE WITH EMC AND LOW
VOLTAGE, Section 6.1, 6.1.2, WARRANTY

A - 8 A - 8
Print Date Manual Number Revision
May, 2016 SH(NA)-080142-O Correction
SAFETY PRECAUTIONS, COMPLIANCE WITH EMC AND LOW
VOLTAGE DIRECTIVES, ABOUT THE GENERIC TERMS AND
ABBREVIATIONS, PACKING LIST, Chapter 1, Chapter 2, Section 2.1,
Section 2.2, Section 2.3, Section 3.1.1, Section 3.1.2, Section 3.2,
Section 3.2.1, Section 3.3.1, Section 3.3.2, Section 3.4.1, Section 3.4.2,
Section 3.4.4, Section 3.4.6, Section 3.4.7, Section 3.4.8, Section 3.4.9,
Section 3.4.10, Section 3.4.13, Section 3.4.14, Section 3.4.25, Section
4.1, Section 4.3, Section 4.5, Section 4.6, Section 5.2.1, Section 5.2.2,
Section 5.4, Section 5.5, Section 5.6.1, Section 5.6.2, Section 5.6.3,
Section 6.1, Section 6.1.1, Section 6.1.2, Section 6.2, Section 6.2.1,
Section 6.2.2, Chapter 7, Section 7.5, Section 8.1, Section 8.2.8,
Section 8.2.9,
Section 8.2.10, Appendix 1.2, Appendix 1.2.1, Appendix 1.3,
Appendix 2.1, Appendix 2.2, Appendix 2.3, Appendix 3
Section number changed
Appendix 2 Appendix 1, Appendix 2.1 Appendix 1.1,
Appendix 2.2 Appendix 1.2, Appendix 2.2.1 Appendix 1.2.1,
Appendix 2.2.2 Appendix 2.2.1, Appendix 2.3 Appendix 1.3,
Appendix 3.1 Appendix 2.1, Appendix 3.2 Appendix 2.2,
Appendix 3.3 Appendix 2.3, Appendix 3.4 Appendix 2.4,
Appendix 4 Appendix 3
Japanese Manual Version SH-080133-R
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent
licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property
rights which may occur as a result of using the contents noted in this manual.
2000 MITSUBISHI ELECTRIC CORPORATION