Mitsubishi GOT1000 GT15 User manual

GT15 User's Manual

A- 1
SAFETY PRECAUTIONS
(Always read these precautions before using this equipment.)
Before using this product, please read this manual and the relevant manuals introduced in this manual
carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".
Note that the caution level may lead to a serious accident according to the circumstances. Always follow
the instructions of both levels because they are important to personal safety.
Please save this manual to make it accessible when required and always forward it to the end user.
[DESIGN PRECAUTIONS]
WARNING
Some failures of the GOT, communication unit or cable may keep the outputs on or off.
Some failures of a touch panel may cause malfunction of the input objects such as a touch switch.
An external monitoring circuit should be provided to check for output signals which may lead to a
serious accident.
Not doing so can cause an accident due to false output or malfunction.
If a communication fault (including cable disconnection) occurs during monitoring on the GOT,
communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.
For bus connection: The CPU becomes faulty and the GOT becomes inoperative.
For other than bus connection: The GOT becomes inoperative.
A system where the GOT is used should be configured to perform any significant operation to the
system by using the switches of a device other than the GOT on the assumption that a GOT
communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
Do not use the GOT as the warning device that may cause a serious accident.
An independent and redundant hardware or mechanical interlock is required to configure the device
that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect output or malfunction.
WARNING Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury or
physical damage.

A- 2
[DESIGN PRECAUTIONS]
WARNING
Incorrect operation of the touch switch(s) may lead to a serious accident if the GOT backlight is gone
out.
When the GOT backlight goes out, the POWER LED flickers (green/orange) and the display section
turns black and causes the monitor screen to appear blank, while the input of the touch switch(s)
remains active.
This may confuse an operator in thinking that the GOT is in "screensaver" mode, who then tries to
release the GOT from this mode by touching the display section, which may cause a touch switch to
operate.
Note that the following occurs on the GOT when the backlight goes out.
• The POWER LED flickers (green/orange) and the monitor screen appears blank
The display section of the GT1595-X is an analog-resistive type touch panel.
If you touch the display section simultaneously in 2 points or more, the switch that is located around
the center of the touched point, if any, may operate.
Do not touch the display section in 2 points or more simultaneously.
Doing so may cause an accident due to incorrect output or malfunction.
CAUTION
Do not bundle the control and communication cables with main-circuit, power or other wiring.
Run the above cables separately from such wiring and keep them a minimum of 100mm (3.94in.)
apart.Not doing so noise can cause a malfunction.
Do not press the GOT display section with a pointed material as a pen or driver.
Doing so can result in a damage or failure of the display section.
When the GOT is connected to the Ethernet network, the available IP addressis restricted according
to the system configuration.
• When multiple GOTs are connected to the Ethernet network :
Do not set the IP address (192.168.0.18) for the GOTs and the controllers in the network.
• When a single GOT is connected to the Ethernet network :
Do not set the IP address (192.168.0.18) for the controllers except the GOT in the network.
Doing so can cause the IP address duplication. The duplication can negatively affect the
communication of the device with the IP address (192.168.0.18).
The operation at the IP address duplication depends on the devices and the system.
Turn on the controllers and the network devices to be ready for communication before they
communicate with the GOT.
Failure to do so can cause a communication error on the GOT.

A- 3
[MOUNTING PRECAUTIONS]
WARNING
Be sure to shut off all phases of the external power supply used by the system before mounting or
removing the GOT main unit to/from the panel.
Not doing so can cause the unit to fail or malfunction.
Be sure to shut off all phases of the external power supply used by the system before mounting or
removing the communication unit, printer unit, option function board or multi-color display board
onto/from the GOT.
Not doing so can cause the unit to fail or malfunction.
When installing the multi-color display board, wear an earth band etc. to avoid the static electricity.
Not doing so can cause a unit corruption.

A- 4
[MOUNTING PRECAUTIONS]
CAUTION
Use the GOT in the environment that satisfies the general specifications described in this manual.
Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.
When mounting the GOT to the control panel, tighten the mounting screws in the specified torque
range (0.36 to 0.48 N·m) with a Phillips-head screwdriver No.2.
Undertightening can cause the GOT to drop, short circuit or malfunction.
Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the
GOT.
When loading the communication unit to the GOT, fit it to the connection interface of the GOT and
tighten the mounting screws in the specified torque range (0.36 to 0.48 N·m) with a Phillips-head
screwdriver No.2.
Undertightening can cause the GOT to drop, short circuit or malfunction.
Overtightening can cause a drop, failure or malfunction due to the damage of the screws or unit.
When mounting the option function board onto the GOT, connect it to the corresponding connector
securely and tighten the mounting screws within the specified torque range (0.25 to 0.35 N·m) with a
Phillips-head screwdriver No.1.
Loose tightening may cause the unit and/or GOT to malfunction due to poor contact.
Overtightening may damage the screws, unit and/or GOT; they might malfunction.
Push the option function board onto the corresponding connector until it clicks, so that it will be
secured firmly.
Push the multi-color display board onto the corresponding connector so that it will be secured firmly.
When inserting a CF card into the GOT, push it into the insertion slot until the CF card eject button
will pop out.
If not properly inserted, a bad connection may cause a malfunction.
When inserting/removing a CF card into/from the GOT, turn the CF card access switch off in
advance.
Failure to do so may corrupt data within the CF card.
When removing a CF card from the GOT, make sure to support the CF card by hand, as it may pop
out.
Failure to do so may cause the CF card to drop from the GOT and break.
Operate and store the GOT in environments without direct sunlight, high temperature, dust, humidity,
and vibrations.
When using the GOT in the environment of oil or chemicals, use the protective cover for oil.
Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT.

A- 5
[WIRING PRECAUTIONS]
WARNING
Be sure to shut off all phases of the external power supply used by the system before wiring.
Failure to do so may result in an electric shock, product damage or malfunctions.
CAUTION
Always ground the FG terminal, LG terminal, and protective ground terminal of the GOT power to the
protective ground conductors dedicated to the GOT.
Not doing so may cause an electric shock or malfunction.
When tightening the terminal screws, use a Phillips-head screwdriver No.2.
Terminal screws which are not to be used must be tightened always at torque 0.5 to 0.8 N·m.
Otherwise there will be a danger of short circuit against the solderless terminals.
Use applicable solderless terminals and tighten them with the specified torque.
If any solderless spade terminal is used, it may be disconnected when the terminal screw comes
loose, resulting in failure.
Correctly wire the GOT power supply section after confirming the rated voltage and terminal
arrangement of the product.
Not doing so can cause a fire or failure.
Tighten the terminal screws of the GOT power supply section in the specified torque range (0.5 to
0.8 N·m).
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.
Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT. Not doing so
can cause a fire, failure or malfunction.
The module has an ingress prevention label on its top to prevent foreign matter, such as wire offcuts,
from entering the module during wiring.
Do not peel this label during wiring.
Before starting system operation, be sure to peel this label because of heat dissipation.
Plug the communication cable into the connector of the connected unit and tighten the mounting and
terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.
Plug the QnA/ACPU/Motion controller (A series) bus connection cable by inserting it into the
connector of the connected unit until it "clicks".
After plugging, check that it has been inserted snugly.
Not doing so can cause a malfunction due to a contact fault.

A- 6
[TEST OPERATION PRECAUTIONS]
[STARTUP/MAINTENANCE PRECAUTIONS]
WARNING
Before performing the test operations of the user creation monitor screen (such as turning ON or
OFF bit device, changing the word device current value, changing the settings or current values of
the timer or counter, and changing the buffer memory current value), read through the manual
carefully and make yourself familiar with the operation method.
During test operation, never change the data of the devices which are used to perform significant
operation for the system.
False output or malfunction can cause an accident.
WARNING
When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
Connect the battery correctly.
Do not perform the following actions to the battery.
• Charging, disassembling, heating, short-circuiting, or soldering the battery, or throwing it into the
fire
Incorrect handling may cause the battery to generate heat, burst or take fire, resulting in injuries or
fires.
Before starting cleaning or terminal screw retightening, always switch off the power externally in all
phases.
Not switching the power off in all phases can cause a unit failure or malfunction.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

A- 7
[STARTUP/MAINTENANCE PRECAUTIONS]
[TOUCH PANEL PRECAUTIONS]
CAUTION
Do not disassemble or modify the unit.
Doing so can cause a failure, malfunction, injury or fire.
Do not touch the conductive and electronic parts of the unit directly.
Doing so can cause a unit malfunction or failure.
The cables connected to the unit must be run in ducts or clamped.
Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental
pulling of the cables or can cause a malfunction due to a cable connection fault.
When unplugging the cable connected to the unit, do not hold and pull the cable portion.
Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable
connection fault.
Do not drop the module or subject it to strong shock.
A module damage may result.
Do not drop or give an impact to the battery mounted to the unit.
Doing so may damage the battery, causing the battery fluid to leak inside the battery.
If the battery is dropped or given an impact, dispose of it without using.
Before touching the unit, always touch grounded metal, etc. to discharge static electricity from
human body, etc.
Not doing so can cause the unit to fail or malfunction.
Replace battery with GT15-BAT by Mitsubishi electric Co. only.
Use of another battery may present a risk of fire or explosion.
Dispose of used battery promptly.
Keep away from children. Do not disassemble and do not dispose of in fire.
CAUTION
For the analog-resistive film type touch panels, normally the adjustment is not required.
However, the difference between a touched position and the object position may occur as the period
of use elapses. When any difference between a touched position and the object position occurs,
execute the touch panel calibration.
When any difference between a touched position and the object position occurs, other object may be
activated. This may cause an unexpected operation due to incorrect output or malfunction.

A- 8
[BACKLIGHT REPLACEMENT PRECAUTIONS]
[DISPOSAL PRECAUTIONS]
[TRANSPORTATION PRECAUTIONS]
WARNING
Be sure to shut off all phases of the external power supply of the GOT (and the PLC CPU in the case
of a bus topology) and remove the GOT from the control panel before replacing the backlight (when
using the GOT with the backlight replaceable by the user).
Not doing so can cause an electric shock.
Replacing a backlight without removing the GOT from the control panel can cause the backlight or
control panel to drop, resulting in an injury.
CAUTION
Wear gloves for the backlight replacement when using the GOT with the backlight replaceable by the
user.
Not doing so can cause an injury.
Before replacing a backlight, allow 5 minutes or more after turning off the GOT when using the GOT
with the backlight replaceable by the user.
Not doing so can cause a burn from heat of the backlight.
CAUTION
When disposing of this product, treat it as industrial waste.
When disposing of batteries, separate them from other wastes according to the local regulations.
(For details of the battery directive in EU member states, refer to 19.4 Handling of Batteries and
Devices with Built-in Batteries in EU Member States.)
CAUTION
When transporting lithium batteries, make sure to treat them based on the transport regulations.
(Refer to Appendix 3 for details of the regurated units.)
Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be
exposed to the impact exceeding the impact resistance described in the general specifications of this
manual, as they are precision devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.

A- 9
REVISIONS
For the software functions, refer to the product-specific screen design manual.
The manual number is given on the bottom left of the back cover.
Print Date Manual Number Revision
Oct., 2004 SH(NA)-080528ENG-A First edition
Mar., 2005 SH(NA)-080528ENG-B Compatible with GT Designer2 Version2.09K
Chapter 6, Section 7.3.2, 8.2 to 8.6 8.2 to 8.4, 8.4.3, Section 9.1 to 9.3
9.1 to 9.2, Section 10.1 to 10.6 10.1 to 10.5, Section 12.1 to 12.6 12.1 to
12.5, Section 13.1, 13.2 to 13.6 13.3 to 13.7, Section 14.1 to 14.2 14.1,
Section 15.1 to 15.2 15.1, Section 16.1 to 16.2 16.1, Chapter 18, Section
18.6 18.3, 18.3 to 18.5 18.4 to 18.6, Section 19.1, 19.2
SAFETY PRECAUTIONS, Section 2.1, 2.2.2, Section 3.2, Section 4.1, 4.2, 4.3,
Section 5.3, Section 7.3.1, 7.5.1, 7.5.2, Section 8.3, Appendix 1, 2, 4
Section 10.6, Section 12.6, Section 13.2
Apr., 2005 SH(NA)-080528ENG-C
Section 4.1, 4.2, 4.3, 7.1.2, 7.5.2, 18.6, Appendix 1, Chapter 5 to 19 6 to 20,
Appendix 2 to 4 3 to 5
Chapter 5, Appendix 2
Sep., 2005 SH(NA)-080528ENG-D Compatible with GT Designer2 Version 2.18U
Chapter 1, Section 1.1, 1.2, Section 2.1, 2.2, 2.2.1, 2.2.2, Section 4.1 to 4.4,
Section 5.1, 5.1.3, 5.2.5, 5.4.2, Section 6.3, Section 7, 7.4, Section 8.1, 8.1.1,
8.1.2, 8.2, 8.3, 8.5.1, 8.5.2, 8.6.2, 8.7.3, 8.7.4, 8.11, 8.11.1, Section 9, 9.1, 9.2,
9.3.1, to 9.3.3, Section 10, 10.1.2 to 10.1.4, 10.2.2, 10.2.3, Chapter 11, 11.1,
11.1.1 to 11.1.3, 11.2.2, 11.2.3, 11.3.1, 11.3.2, 11.4.2, 11.5.1 to 11.5.3, Section
12.1.1 to 12.1.3, Section 13, 13.1.2, 13.1.3, 13.2.1, 13.2.2, 13.2.4, 13.3.2 to
13.3.4, 13.4.2, 13.5.2, 13.6.1 to 13.6.3, 13.7, 13.7.1, 13.7.2, 13.7.4, 13.7.5,
Chapter 14, 14.1.2, 14.2.1, 14.3.1 to 14.3.3, 14.4.2, 14.5.2, 14.6.2, 14.7.1,
14.7.2, Section 15.1.2, Section 16.1.3, Section 17.1.3, Chapter 18, 18.1, 18.2,
18.3, 18.3.1, 18.3.2, 18.4, Section 20.1, 20.2, Appendix 5
Section 5.3.2, 5.3.3, Section 6.2, 6.5, Section 8.4.1, 8.7.2, 8.8.1, 8.10.1, 8.10.2,
Section 10.2.1, Section 11.2.1, 11.3.3, Section 13.1.5, Section 14.1.1, Section
19.2, 19.4, 19.5, 19.6.1, 19.6.2, Appendix 1, 3
Section 3.2.1 to 3.2.4, 3.3.1, 3.3.2, Section 4.1, Section 8.5.3, Section 11.6,
11.8, Section 13.8, 13.9, 13.10, Section 18.5
Section 4.1 to 4.3 Section 4.2 to 4.4
Section 11.6 Section 11.7
Partial corrections
Partial additions
Additions
Partial corrections
Additions
Partial corrections
Partial additions
Additions

A- 10
The manual number is given on the bottom left of the back cover.
Print Date Manual Number Revision
Jan., 2006 SH(NA)-080528ENG-E Compatible with GT Designer2 Version2.27D
SAFETY PRECAUTIONS, Chapter 1, Section 2.1, Section 8.1.1, 8.5 to
8.11 8.6 to 8.12, Section 9.2, 9.3, Section 10.1.3, Section 11.1, 11.7.2, Section
13.7.4, 13.10.4
Section 2.2, Section 6.3, Section 13.1.5, 13.2.4, Chapter 14, Section 19.4,
Section 20.2, Appendix 1, 3, 5
Section 8.5, Section 14.8, 14.9
Jun., 2006 SH(NA)-080528ENG-F Compatible with GT Designer2 Version2.32J
Chapter 1, Section 1.1, 2.1, 2.2, 4.1, 4.2, 4.3, 4.4, 5.3.1, 5.4.2, 8.4, 8.5.2, 8.9,
9.3, 11.2.2, 11.3.2, 11.4.2, 11.5.2, 11.7.2, 11.8.2, 12.1.3, 13.1.5, 13.2.2, 13.2.3,
13.2.4, 13.3.1, 13.3.3, 13.4.2, 13.4.3, 13.5.2, 13.5.3, 13.6.2, 13.6.3, 13.7.2,
13.7.3, 13.8.2, 13.8.3, 13.9.2, 13.10.2, 13.10.3, 14.3.2, 14.4.2, 14.5.2, 14.6.2,
14.7.2, 14.9, 18.3.1, 18.4, 18.5.2
Chapter 1, Section 2.2.1, 2.2.2, 3.2.1 ~ 3.2.4, 3.3.1, 3.3.2, 5.3.2, 5.3.3, 6.2, 6.3,
7.1, 7.4, 8.1.2, 8.3.1, 8.7, 8.8, 8.10, 8.11, 8.12, 8.13, 9.2, 9.3.1, 10.1.3, Chapter
11, Section 11.1.1, 11.1, 2, 11.5.1, 11.7.1, 11.8.1, Chapter 14, Section 14.1.1,
14.2.1, 19.6.1, 20.2, Appendix 1, 3, 5
Section 3.2.5, 4.5, 5.3.4, 8.6, 11.9 ~ 11.11, 13.11, 14.8
Sep., 2006 SH(NA)-080528ENG-G
Section 5.1.1, 5.2.4, 5.3.2, 5.3.3, 5.3.6, 5.4.2
Nov., 2006 SH(NA)-080528ENG-H Compatible with GT Designer2 Version2.43V.
SAFETY PRECAUTIONS, Section 2.2.2, 3.1, 3.2, 3.3, 4.2, 4.3, 4.5, Chapter 7,
Section 8.1 8.6, 8.2 8.7, 8.3 8.8, 8.4 8.14, 8.5 8.3, 8.6 8.4, Section
8.6.2, 8.7 8.1, 8.7.2, 8.7.3, 8.8 8.2, 10.1.3, 11.2.1, 11.3.1, 11.7.1, 11.7.2,
11.8.1, 12.1.3, 14.9.2, 14.9.3, 18.4, Chapter 20, Section 20.2
Section 2.2.1, 2.2.2, 3.2.2, 3.2.3, 3.3.2, 5.3.1, 5.3.4, 6.3, 9.2, Chapter 11,
Section 11.1.1, 11.1.3, 11.3.3, 13.1.1, 13.1.2, 13.1.5, 13.2.1, 13.2.2, 13.2.3,
13.2.4, 13.3.1, 13.3.2, 13.3.4, 13.4.1, 13.4.2, 13.4.3, 13.5.2, 13.5.3, 13.6.2,
13.7.2, 13.8.2, 13.9.2, 13.9.3, 13.10.1, 13.10.2, 13.10.3, 13.10.4, 13.11.2,
13.12.3, 14.3.1, 14.3.3, Chapter 17, Section 17.1.3, 18.3, 18.3.1, 19.6.2,
Appendix 1, 3, 5
Section 8.5, 13.12
Partial corrections
Partial additions
Additions
Partial corrections
Partial additions
Additions
Partial corrections
Partial corrections
Partial additions
Additions

A- 11
The manual number is given on the bottom left of the back cover.
Print Date Manual Number Revision
Feb., 2007 SH(NA)-080528ENG-I Compatible with GT Designer2 Version2.47Z.
Section 3.2.1, 3.2.2, 3.2.3, 3.2.4, 3.2.5, 6.1, 6.2, 7.2, 7.6, 7.6.1, 7.6.2, 10.1.3,
11.2.3, 13.1.2, 20.3.2, Appendix 1
Section 2.2.2, 5.2.3, 5.3.4, 6.2, 6.3, 8.5, 8.5.1, 8.5.2, 8.6.3, 14.7.1
Section 8.5.3, 8.5.4, 8.6.4, Appendix 5
May, 2007 SH(NA)-080528ENG-J Compatible with GT Designer2 Version 2.58L
Section 2.2, 3.2.3, 3.2.5, 3.3, 5.4.1, 6.3, 7.2, 8.5 8.7, 8.6 8.8, 8.7 8.9,
8.8 8.10, 8.9 8.11, 8.10 8.12, 8.11 8.13, 8.12 8.14, 8.16.1, 9.2, 10.1.3,
10.2.3, 11.7.1, 11.7.2, 11.7.3, 13.5.2, 13.5.3, 14.1.1, 14.1.2, 14.7, 20.3.2,
Appendix 3, 6
Section 2.2.1, 2.2.2, 3.2.1, 4.5, 5.2.3, 5.3.1, 5.3.4, 8.8, 11.7.1, 13.5.1, 13.5.4,
Chapter 14, 20.3.1, Appendix 1, 6
Section 8.5, 8.6, 11.2, 14.11
Jul., 2007 SH(NA)-080528ENG-K Compatible with GT Designer2 Version 2.62R
Section 14.7.1, 19.6.1, 19.6.2
Section 9.2, 14.1, 20.3.2
Nov., 2007 SH(NA)-080528ENG-L Compatible with GT Designer2 Version 2.73B
Section 3.2.1, 3.2.2, 3.2.3, 3.2.4, 3.2.5, 8.1.1, 8.1.2, 8.2.2, 8.3.2, 8.4.2, 8.5.2,
8.6.2, 8.8.2, 8.10.1,8.10.2, 8.16.1, 8.16.2, 13.7.2, 13.8.2, 14.7.1, 14.7.3, 19.6.2,
Appendix 3
Section 1.2, 2.1, 2.2.2, 3.2, 5.3.1, 9.2, 10.1.3, Chapter 11, 11.12.1, 11.12.2,
11.12.3, 13.2.1, 13.3.1,13.10.2, Chapter 18, 18.1. 18.2, 18.3.1
Section 11.13
Feb., 2007 SH(NA)-080528ENG-M Compatible with GT Designer2 Version 2.77F
Section 1.2
SAFETY PRECAUTIONS, Section 2.2.2, 3.2, 5.3, 6.3, 8.1, 9.2, Chapter 14,
Section 20.3.2, Appendix 1, 3
Partial corrections
Partial additions
Additions
Partial corrections
Partial additions
Additions
Partial corrections
Partial additions
Partial corrections
Partial additions
Additions
Partial corrections
Partial additions

A- 12
The manual number is given on the bottom left of the back cover.
Print Date Manual Number Revision
Dec., 2008 SH(NA)-080528ENG-N Compatible with GT Designer2 Version2.91V
Section 8.11.4, 8.13.2, 18.3.1
SAFETY PRECAUTIONS, Section 2.1, 2.2.2, 3.1, 3.2.2, 6.2, 6.3, 6.4, 8.3.2,
8.8.1, 8.11.2, 9.2, 10.1.3, 12.1.3, Chapter 14, Section 14.11.1, 14.11.3, 19.4,
Appendix 1, Appendix 3
Section 8.18, 14.12
Mar., 2009 SH(NA)-080528ENG-O Compatible with GT Designer2 Version2.96A
Section 6.3, 10.1.3, 10.2.2, 14.7.1, Appendix 1
Section 2.2, 2.2.2, 3.2, 8.1.1, 9.2, 13.3.1, Appendix 3, Appendix 18
Jun., 2009 SH(NA)-080528ENG-P Compatible with GT Designer2 Version2.96A
Chapter 5
Oct., 2009 SH(NA)-080528ENG-Q Compatible with GT Designer3 Version1.01B
Additional information to be compatible with GT Designer3
Jan., 2010 SH(NA)-080528ENG-R Compatible with GT Designer3 Version1.10L.
For SAFETY PRECAUTIONS, the usage of a battery added, the usage of a
protective cover for oil added
• Compatible with the communication between the PC and GOT via modem
• Compatible with the connection to LCPU
• SoftGOT-GOT link function supported
• Change in the insulation sheets for protecting cables supported
Feb., 2010 SH(NA)-080528ENG-S • Compliance with the EMC Directive by the GT1595 power specification
change
• Change in the FG and LG wiring diagram between a PLC and the GOT
• Model name of a ferrite core added
May, 2010 SH(NA)-080528ENG-T Compatible with GT Designer3 Version1.14Q.
Section 11.7
Jun., 2010 SH(NA)-080528ENG-U Compatible with GT Designer3 Version1.17T.
Chapter 3
Oct., 2010 SH(NA)-080528ENG-V Compatible with GT Designer3 Version1.19V.
• Compatible with switching the display order of operation logs on the operation
log information screen.
Partial corrections
Partial additions
Additions
Partial corrections
Partial additions
Partial additions
Partial additions
Partial corrections

A- 13
The manual number is given on the bottom left of the back cover.
Print Date Manual Number Revision
Jan., 2011 SH(NA)-080528ENG-W Compatible with GT Designer3 Version1.23Z.
• Compatible with the Ethernet settings check and the change of the host
• Compatible with "no setting" of the utility call key.
• Compatible with the setting of [Operating priority guaranteed time]/[Operation
status popup notification] in the [SoftGOT-GOT link] screen
• Compatible with the setting of [Comment setting] in the [Q/L/QnA ladder
monitor] screen
• Compatible with Behavior of duplicate IPs.
• Compatible with the latest display in Operation log information
Jul., 2011 SH(NA)-080528ENG-X Compatible with GT Designer3 Version1.31H
• CC-Link IE Field Network communication unit added
• Error codes added
• Compatible with Behavior of duplicate IPs
• Compatible with Save ladder programs setting of Q/L/QnA ladder monitor
• Compatible with language setting of special data
Jan., 2012 SH(NA)-080528ENG-Y Compatible with GT Designer3 Version1.40S
• Error codes added
Apr., 2012 SH(NA)-080528ENG-Z Compatible with GT Designer3 Version1.45X
• Correction of SAFETY PRECAUTIONS
• Compatible with the specification change of JIS B 3502
• Correction of description of the GOT installation position
Jun., 2012 SH(NA)-080528ENG-AA Compatible with GT Designer3 Version1.54G
• The company name of Panasonic Electric Works Co., Ltd. is changed to
Panasonic Corporation.
• The company name of Yamatake Corporation is changed to Azbil
Corporation.
• For the drawing check function, gray is added to the color displayed at the
missing bit check and the color check.
Nov., 2012 SH(NA)-080528ENG-AB Compatible with GT Designer3 Version1.63R
• Corrective action for the error code added
Feb., 2013 SH(NA)-080528ENG-AC Compatible with GT Designer3 Version1.67V
• The backup/restore function supports the check changes.
• Corrective action for the error code added
• Error code list deleted

A- 14
The manual number is given on the bottom left of the back cover.
© 2004 MITSUBISHI ELECTRIC CORPORATION
Print Date Manual Number Revision
Jun., 2013 SH(NA)-080528ENG-AD Compatible with GT Designer3 Version1.74C
• Correction of SAFETY PRECAUTIONS
• The company name of GE Fanuc Automation Corporation is changed to GE
Intelligent Platforms.
• The company name of Panasonic Corporation is changed to Panasonic
Industrial Devices SUNX Co., Ltd.
• The company name of Fuji Electric FA Components & Systems Co., Ltd. is
changed to FUJI ELECTRIC CO., LTD.
• The company name of Fuji Electric Systems Co., Ltd. is changed to FUJI
ELECTRIC CO., LTD.
Sep., 2013 SH(NA)-080528ENG-AE Compatible with GT Works3 Version1.100E
Jan., 2014 SH(NA)-080528ENG-AF Compatible with GT Works3 Version1.108N
• The display angle of the LCD of GT1555-QSBD is changed.
• The Operation Log Data List screen is changed.
• The I/O check and a part of driver names are changed.
Apr., 2014 SH(NA)-080528ENG-AG • Writing errors have been corrected.
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.
Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.

A- 15
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 1
REVISIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 9
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 15
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 15
ABOUT MANUALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 25
QUICK REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 28
ABBREVIATIONS AND GENERIC TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 30
HOW TO READ THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 35
PACKING LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A - 36
1. OVERVIEW 1 - 1 to 1 - 4
1.1 Features 1 - 2
1.2 Rough Pre-operation Procedure 1 - 3
2. SYSTEM CONFIGURATION 2 - 1 to 2 - 20
2.1 Overall Configuration 2 - 1
2.2 Component List 2 - 2
2.2.1 GOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5
2.2.2 Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 7
3. SPECIFICATIONS 3 - 1 to 3 - 20
3.1 General Specifications 3 - 1
3.2 Performance Specifications 3 - 3
3.2.1 GT1595-X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
3.2.2 GT1585V-S, GT1585-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
3.2.3 GT1575V-S, GT1575-S, GT1575-V, GT1575-VN, GT1572-VN . . . . . . . . . . . . . . . . . . . . . . 3 - 9
3.2.4 GT1565-V, GT1562-VN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 13
3.2.5 GT1555-V, GT1555-Q, GT1550-Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 16
3.3 Power Supply Specifications 3 - 19
3.3.1 For GOTs powered from the 100 to 240VAC power supply . . . . . . . . . . . . . . . . . . . . . . . . 3 - 19
3.3.2 For GOTs powered from the 24VDC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 20
4. PART NAME AND SETTINGS 4 - 1 to 4 - 12
4.1 Part Names and Settings of the GT1595 4 - 1
4.2 Part Names and Settings of the GT1585 4 - 3
INTRODUCTION
Thank you for choosing the Mitsubishi Graphic Operation Terminal.
Before using the equipment, please read this manual carefully to use the equipment to its optimum.
CONTENTS

A- 16
4.3 Part Names and Settings of the GT157 4 - 6
4.4 Part Names and Settings of the GT156 4 - 9
4.5 Part Names and Settings of the GT155 4 - 11
5. EMC AND LOW VOLTAGE DIRECTIVE 5 - 1 to 5 - 24
5.1 Requirements to Meet EMC Directive 5 - 1
5.1.1 EMC directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2
5.1.2 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4
5.1.3 Noise filter (power supply line filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5
5.2 Requirements for Conpliance with the Low Voltage Directive 5 - 6
5.2.1 Standard subject to GOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
5.2.2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
5.2.3 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
5.2.4 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
5.2.5 External wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 8
5.3 EMC Directive-Compliant System Configuration 5 - 9
5.3.1 GOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 9
5.3.2 Connection method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 10
5.3.3 When the communication unit is used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 11
5.3.4 When the option unit is used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 13
5.3.5 When the option is used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 13
5.3.6 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 14
5.4 Precautions for Wiring/Connecting the EMC Directive-Compliant Product 5 - 15
5.4.1 Power and ground wires wiring method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 15
5.4.2 Processing connection cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 18
5.4.3 Grounding the cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 24
6. INSTALLATION 6 - 1 to 6 - 12
6.1 Control Panel Inside Dimensions for Mounting GOT 6 - 1
6.2 Panel Cutting Dimensions 6 - 2
6.3 Mounting Position 6 - 3
6.4 Control Panel Inside Temperature and Mounting Angle 6 - 11
6.5 Installation Procedure 6 - 11
7. WIRING 7 - 1 to 7 - 16
7.1 Power Supply Wiring 7 - 3
7.2 Wiring to GOT Power Section 7 - 4
7.3 Grouding 7 - 6
7.3.1 Grounding the GOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 6
7.3.2 Wiring-related malfunction causes and the measures examples . . . . . . . . . . . . . . . . . . . . 7 - 9
7.4 Panel Inside Wiring, Panel Outside Wiring 7 - 11
7.4.1 Panel inside wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 11
7.4.2 Panel outside wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 11
7.5 Attaching Surge Suppressor for Control Equipment 7 - 12

A- 17
7.6 Grounding Extension Units 7 - 13
7.6.1 Wiring FG cable of bus connection cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 13
7.6.2 Wiring FG cable of CF card extension unit connection cable . . . . . . . . . . . . . . . . . . . . . . . 7 - 15
8. OPTION 8 - 1 to 8 - 62
8.1 Communication Unit 8 - 1
8.1.1 Applicable communication unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
8.1.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 3
8.1.3 Installing multiple extension units in layers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 15
8.2 RS-422 Conversion Unit 8 - 17
8.2.1 Applicable RS-422 conversion unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 17
8.2.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 17
8.3 Printer Unit 8 - 18
8.3.1 Printer unit type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 18
8.3.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 18
8.4 Video/RGB Unit 8 - 22
8.4.1 Video/RGB unit types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 22
8.4.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 22
8.5 External I/O Unit 8 - 25
8.5.1 Applicable external I/O unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 25
8.5.2 Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 25
8.6 Sound Output Unit 8 - 27
8.6.1 Applicable sound output unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 27
8.6.2 Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 27
8.7 CF Card Unit and CF Card Extension Unit 8 - 30
8.7.1 Applicable CF card unit and CF card extension unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 30
8.7.2 Installing on GOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 30
8.7.3 Installing on control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 32
8.7.4 Protective structure for CF card extension unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 33
8.8 CF Card 8 - 34
8.8.1 Applicable CF card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 34
8.8.2 CF card inserting/removing method with CF card interface of GOT. . . . . . . . . . . . . . . . . . 8 - 35
8.8.3 CF card inserting/removing method with CF card unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 39
8.8.4 CF card inserting/removing method with CF card extension unit . . . . . . . . . . . . . . . . . . . . 8 - 41
8.9 Memory Card Adaptor 8 - 43
8.9.1 Applicable memory card adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 43
8.9.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 43
8.10 Option Function Board 8 - 44
8.10.1 Applicable option function board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 44
8.10.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 44
8.11 Battery 8 - 46
8.11.1 Applicable battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 46
8.11.2 Battery specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 46
8.11.3 Battery replacement procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 46
8.11.4 Battery life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 47

A- 18
8.12 Protective Sheet 8 - 48
8.12.1 Applicable protective sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 48
8.12.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 49
8.13 Protective cover for oil 8 - 50
8.13.1 Applicable protective cover for oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 50
8.13.2 Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 50
8.14 USB Environmental Protection Cover 8 - 54
8.14.1 Applicable USB environmental protection cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 54
8.14.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 54
8.15 Stand 8 - 56
8.15.1 Applicable stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 56
8.15.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 56
8.16 Attachment 8 - 58
8.16.1 Applicable attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 58
8.16.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 59
8.17 Multi-Color Display Board 8 - 61
8.17.1 Applicable multi-color display board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 61
8.17.2 Installing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 62
9. UTILITY FUNCTION 9 - 1 to 9 - 12
9.1 Utility Execution 9 - 1
9.2 Utility Function List 9 - 2
9.3 Utility Display 9 - 5
9.3.1 Display operation of main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 7
9.3.2 Utility basic configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 10
9.3.3 Basic operation of settings change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 11
10. COMMUNICATION INTERFACE SETTING
(COMMUNICATION SETTING) 10 - 1 to 10 - 21
10.1 Communication Setting 10 - 1
10.1.1 Communication setting functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
10.1.2 Communication setting display operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2
10.1.3 Communication setting contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
10.1.4 Communication setting display operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 7
10.2 Communication Detail Settings 10 - 13
10.2.1 Communication detail settings functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 13
10.2.2 Communication detail settings display operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 13
10.2.3 Display contents of communication detail settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 15
10.3 Ethernet Setting 10 - 19
10.3.1 Ethernet setting function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 19
10.3.2 Display operation of Ethernet setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 19
10.3.3 Display contents of Ethernet setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 20