ML Accessories Knightsbridge SK0012 Instruction Manual

1
INSTALLATION & MAINTENANCE MANUAL
SK0012
ACCESSORIES LTD 11
IP
20

2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product: SK0012
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class II double insulated
• This product is IP20 rated
Note – The selected surface of installation must be at least 10mm thick.
This product is designed to fit into standard sized office desk cut-outs of 60mm or 80mm, without the need
to cut further holes (see Fig. 1)
INSTRUCTIONS –SK0012
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product: SK0012
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•This product is Class II double insulated
•This product is IP20 rated
INSTALLATION
Note –The selected surface of installation must be at least 10mm thick.
•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1)
Fig. 1
•Insert the 60mm or 80mm ring into the cut-out (see Fig. 2)
Fig. 2
•Insert the USB charger and lock (see Fig. 3)
Fig. 3
INSTRUCTIONS –SK0012
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product: SK0012
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•This product is Class II double insulated
•This product is IP20 rated
INSTALLATION
Note –The selected surface of installation must be at least 10mm thick.
•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1)
Fig. 1
•Insert the 60mm or 80mm ring into the cut-out (see Fig. 2)
Fig. 2
•Insert the USB charger and lock (see Fig. 3)
Fig. 3
Fig. 1
Fig. 2
• Insert the 60mm or 80mm ring into the
cut-out (see Fig. 2)
• Insert the USB charger and lock (see Fig. 3)

7
WARNING
GENERAL
WARRANTY
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch
code will invalidate the warranty. If this product should fail within its warranty period it should be returned
to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for
any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
INSTRUCTIONS –SK0012
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product: SK0012
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•This product is Class II double insulated
•This product is IP20 rated
INSTALLATION
Note –The selected surface of installation must be at least 10mm thick.
•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1)
Fig. 1
•Insert the 60mm or 80mm ring into the cut-out (see Fig. 2)
Fig. 2
•Insert the USB charger and lock (see Fig. 3)
Fig. 3
Fig. 3
• Connect to the plug-in adapter, plug into a
socket and check for correct operation

ML Accessories Limited
LU5 4LT
www.mlaccessories.co.uk AVNOV19_V1
ACCESSORIES LTD
8