Mobotix T26 Original operating instructions

Quick Installation
Door Station T26
33.095-001_EN_10/2018

2
T26 Quick Installation
Step 1 – Start The Auto Conguration
Connect And Start Up The Devices
Connect all the devices as shown in the connection diagram in the enclosed System Manual Part 1,
Chapter 2.1.3. Switch on the power supply (MxDisplay+ via PoE-switch or NPA PoE set, door station
via PoE switch). Aer the MxDisplay+ has started up, disconnect the door station briey from the
power supply (for example, remove network connector). Then restore the power supply to the door
station(s) (e.g. plug in the network plug). This restarts the boot process.
Press The Bell Button On The Camera Module
The red LED lights up approx. 5-10 s for 10 s aer the power supply has been established. Press the
light button briey during this time.
The LED now ashes once and repeats this ashing signal aer a pause of one second. Then press
the light button longer (> 2 s). The camera acknowledges the selection by a 3 s fast ash and a ring
tone aer 20 s. The autoconguration starts.
Each MxDisplay+ device is recongured from the T26 and reboots with an updated conguration.
The network data of the camera is announced (e.g. IP address). The camera LEDs will then light, the
keypad number buttons will ash white, the ESC/ALARM button will ash red, and the OK/MENU
button will ash blue.
• 5 - 10 s aer establishing
the power supply, the red
LED lights up.
• Briey press the light
button within 10 seconds.
• Then press and hold the
light button (> 2 s).

3
Step 2 – Enter Super PIN
Choose an 8 to 16 digit number. The number should not be composed only of zeros and must be
diicult to guess. Important: Make a note of the Super PIN straight away and keep it in a safe place!
Enter the Super PIN and press the OK/MENU button. Enter the Super PIN again and press the OK/
MENU button.
The input of the Super-PIN is conrmed by the KeypadRFID showing a ring-shaped ashing pattern.
Step 3 – Set Up RFID Cards
Set Up Red Admin Card
Aer you have entered your Super PIN, the keypad number buttons light up white, the bell, key and
OK/MENU buttons ash blue and the ESC/ALARM button ashes red.
Now hold the Admin card in front of the keypad for approximately ve seconds until you no longer
hear any beeps.
Set Up Blue User Cards
Aerwards, the keypad remains in Add mode for two minutes to allow you to train the User cards,
i. e.,the bell button, key button, OK/MENU button and ESC/ALARM button all ash blue.
Hold a User card to be set up in front of the keypad until a beep sounds. You can now set up as many
additional User cards as you choose, simply by holding them in front of the keypad. To exit the Add
mode before completion, press the ESC/ALARM button.
0 9
Super-PIN
OK 0 9
Super-PIN
OK
Add mode Hold in front for ve seconds Conrm
Add mode Hold briey in front Conrm

4
T26 Quick Installation
Step 4 – Customize System Via MxDisplay+
Aer the autoconguration has been completed and the access modules have been set up, you still
have to set up MxDisplay+ as the remote terminal.
Add the door stations using the installation wizard and then set up the door stations. This includes
conguring the door and door latch contacts, disabling auto-conguration, and activating recording.
Dene the ringing behaviour for each doorbell and assign the bells to the MxDisplay+ device. Set
the date and time on the device. The settings to be made are carried out on an MxDisplay+. If
several MxDisplay+ devices are used, you only need to transfer the settings of the rst device to
the other devices. A detailed description of the system adjustment can be found in the System
Manual Part 2, Section 2.4.
Step 5 – Secure System Via MxDisplay+
By securing the system, you prevent unauthorised persons from gaining unwanted access to the
door station and its remote stations. The door camera has already received secure access data with
the learning of the Super PIN: User name: admin, camera admin password: current Super PIN.
Change the MxDisplay+ web password, lock the autoconguration and save the current system
conguration. A detailed description of the system backup can be found in the System Manual
Part 2, Section 2.5.
Fig.: Aer autoconguration, the MxDisplay+ is opened in standby mode with date/time display.
Fig.: Changing the web password under menu item Administrator.