Mobotix T26 User guide

System Manual Part 1
System Overview and Installation
DoorStation T26
33.071-002_EN_05/2020

2
T26 System Manual Part 1
Access module (KeypadRFID or BellRFID)
• Keyless access (RFID and PIN)
• Operate voice mailbox
• Contact remote stations
• Incl. RFID transponder cards
Info Module/Info Module Mx2wire+
• With integrated Mx2wire+ unit (optional)
• Data and power (PoE) via two-wire connection
• Instead of connection via network cable
• For two-wire cables up to 500m
MX-DoorMaster (indoors)
• Opens door, doorbell on/o
• Status LEDs for door and messages
• Backup power supply with battery
• Connects to door opener and sensors
T26-CamCore (camera module)
• Allround view with no blind spots
• Internal memory
• Speaker
• Microphone
Cindy Jones
Thomas Jones
Dr. Jones, MD

3
Table of Contents
SYSTEM MANUAL PART 1 – SYSTEM OVERVIEW AND INSTALLATION
This T26 System Manual Part 1, «System Overview and Installation» is supplemented by the T26
System Manual Part 2, «Initial Operation and Conguration»
. If you no longer have a manual at
your disposal, you can download a PDF le from the MOBOTIX website (www.mobotix.com >
Support > Download Center > Documentation > Manuals).
TABLE OF CONTENTS
Legal Notes 6
Safety Warnings 7
Foreword 8
Overview of the System Components 22
1 System Overview 24
1.1 Outdoor Station 24
1.1.1 Hemispheric Camera T26-CamCore 24
1.1.2 ETH Module (Ethernet Terminal Board) 26
1.1.3 Access Module KeypadRFID 28
1.1.4 Access Module BellRFID 30
1.1.5 Info Module 32
1.1.6 Info Module Mx2wire+ (With Mx2wire+ Indoor Unit) 34
1.1.7 Housing and Module Frames 38
1.2 MX-DoorMaster 44
1.3 Remote Stations 46
1.3.1 MxDisplay+ 46
1.3.2 MOBOTIX MxBell 48
1.3.3 MxManagementCenter 49
1.4 Accessories 50
1.4.1 NPA-PoE Set 50
1.4.2 IO Module (Extended Terminal Board) 51
1.4.3 MX-Overvoltage-Protection-Box 51
1.4.4 MX-GPS-Box 52
1.4.5 Additional Devices for PoE Power Supply 52
1.4.6 Additional Video Remote Stations 53
1.4.7 Door Sensors 53
1.4.8 Electrical Door Opener 53
2 Installation 54
2.1 Overview: Connection and Wiring Diagrams 54
2.1.1 With MX-DoorMaster 54
2.1.2 Without MX-DoorMaster 56
2.1.3 With Info Module Mx2wire+ and MX-DoorMaster 58

44
Table of Contents
2.1.4 Recommendation for Cabling 60
2.1.5 Installation Tip: Replacing an Existing Doorbell by a T26 62
2.2 Remote Stations and Network Connection 64
2.2.1 Notes on Cable Lengths and Power Supply 64
2.2.2 Direct Connection of One Remote Station 64
2.2.3 Network Connection with Multiple Remote Stations 65
2.3 Mounting the Frame and Housing 68
2.3.1 Determining the Installation Position 68
2.3.2 Inserting the Cables 70
2.3.3 Attaching the Housing 72
2.3.4 Cabling in the On-Wall Housing 74
2.3.5 Mounting the Terminal Board and Fitting the Network Cable 76
2.3.6 Applying the Gasket 77
2.3.7 Attaching the Frame and Connecting the The Protection 78
2.3.8 Mechanical The-Protection Lock 80
2.4 Installing the T26 Modules 82
2.4.1 Installing the T26-CamCore Camera Module 82
2.4.2 Preparing the BellRFID Access Module 86
2.4.3 Installing the Access Module (KeypadRFID/BellRFID) 88
2.4.4 Installing the Info Module 92
2.4.5 Installing the Info Module Mx2wire+ 94
2.4.6 Labeling the Info Module 96
2.4.7 Removing, Exchanging and Modifying Modules 98
2.5 Installing the MX-DoorMaster 100
2.5.1 Overview of Connectors 100
2.5.2 Connection Diagrams for Door Opener Versions 102
2.5.3 Mounting Instructions 104
2.5.4 Installation Using Cavity or In-Wall Socket 107
2.6 Installing the Mx2wire+ Indoor Unit 110
2.6.1 Overview of Mx2wire+ Technology and Connectors 110
2.6.2 Mounting Instructions 112
2.6.3 Installation Using Cavity or In-Wall Socket 113
2.6.4 Installation With Surface-Mounted Socket 115
2.6.5 Function of Mx2wire+ Status LEDs 117
2.7 Connecting External Devices to the Door Station 118
2.7.1 Using the IO Module 118
2.7.2 Using the Signal Outputs of the Access Module (KeypadRFID/BellRFID) 122
2.8 Finishing the Installation 124
2.8.1 Checking the Wiring and Activating The Protection 124
2.8.2 Conguring the MX-DoorMaster 126

5
Table of Contents

66
Table of Contents
LEGAL NOTES
Legal aspects of video and sound recording: You must comply with all data protection
regulations for video and sound monitoring when using MOBOTIX products. Depending
on national laws and the installation location of the T26, the recording of video and sound
datamaybesubjecttospecialdocumentationoritmay be prohibited.AllusersofMOBOTIX
products are therefore required to familiarize themselves with all applicable regulations
and to comply with these laws. MOBOTIX AG is not liable for any illegal use of its products
§

7
SAFETY WARNINGS
Notes on Installing:
• This product must not be used in locations exposed to the dangers of explosion.
• Make sure that you install this product as outlined in Chapter 2, «Installation» of the
corresponding manual. A faulty installation can damage the camera!
• When installing this product, make sure that you are only using genuine MOBOTIX
parts and MOBOTIX connection cables.
• Only install this product on suitable, solid materials that provide for a sturdy installa-
tion of the xing elements used.
Electrical installation: Electrical systems and equipment may only be installed, modied
and maintained by a qualied electrician or under the direction and supervision of a qual-
ied electrician in accordance with the applicable electrical guidelines. Make sure to prop-
erly set up all electrical connections.
Electrical surges: MOBOTIX cameras are protected against the eects of small electrical
surges by numerous measures. These measures, however, cannot prevent the camera from
being damaged when stronger electrical surges occur. Special care should be taken when
installing the camera outside of buildings to ensure proper protection against lightning,
since this also protects the building and the whole network infrastructure.
Max. power consumption of attached extension modules: The power consumption of all
attached
MxBus modules must not exceed 3 W . When attaching modules to the MxBus
connector
and the USB socket, the power consumption of all attached modules must
not exceed 4 W
, if the camera is powered by PoE class 3 . If PoE class 2 is used, the power
consumption of all attached modules must not exceed 1 W!
Risk of overheating when exposed to direct sunlight: When mounting a black, dark gray
oramber-coloredT26DoorStationinlocationswherethedeviceis exposedtodirectsunlight,
the housing temperature can exceed the maximum allowed temperature limit. This can
result in electronic failures and injuries especially when touching exterior metal parts. If the
intended use of the device is at an (unprotected) outdoor location, you should only install
white or silver-colored modules and frames. This product must not be installed within the
reach of persons without the dome.
Power o before opening the camera: Make sure the power supply to the camera is discon-
nected before opening the camera housing (e.g., when inserting or exchanging lenses, lens
units and SD cards).
Network security: MOBOTIX products include all of the necessary conguration options for
operation in Ethernet networks in compliance with data protection laws. The operator is
responsible for the data protection concept across the entire system. The basic settings
required to prevent misuse can be congured in the soware and are password-protected.
This prevents unauthorized parties from accessing these settings.

8
T26 System Manual Part 1
FOREWORD
Dear MOBOTIX customer,
Congratulations on your decision to purchase an exceptionally versatile and innovative
DoorStation “made in Germany.” The T26 system contains a hemispheric door camera
with a 6 megapixel color sensor (T26-CamCore) and captures the entire room 180° from
wall to wall and from oor to ceiling without any blind spots.
Another plus – the improved light sensitivity of the 6MP sensors, which
drastically reducesexposure times. In conjunctionwith MxLEO, the exposure
and image optimization program working in the background, the camera
generates perceptibly better and more detailed images especially under
low-light conditions. This signicantly reduces motion blur that is typical
of longer exposure times with little light and thus provides much more
image detail (faces, etc.) for proper identication.
Chapter 1,«SystemOverview», of this manualcontains all product details
andthe technicalinformationofthesystem.Chapter 2,«Installation»,deals
with the installation of the T26 with a direct network connection or the
optionalconnectionviatwo(existing)wires.TheT26SystemhandbuchTeil 2
will demonstrate how you operate the door station and congure it to
meet your specic needs. The system manuals are supplemented by the
T26 Quick Guide .
Forinstallingthe DoorStationandforrunningitona day-today basis,MOBOTIXrecommends
using the MxDisplay+. The MxManagementCenter video management soware, which is
tailoredto MOBOTIX cameras,can be downloaded from the MOBOTIX websitefreeofcharge:
www.mobotix.com > Support > Download Center > Soware Downloads. The tutorial for
theapplicationisavailableunderSupport > Download Center > Documentation > Brochures
& Guides > Tutorials. MOBOTIX also provides a mobile solution for iOS/Android devices
(iOS10/Android4.4 and higher). Search for “MOBOTIX AG” in the App Store or on Google
Play to nd the free MOBOTIX MxBell app.
If you still have any questions, our support and international sales sta are available at
[email protected] from Monday through Friday.
We would like to thank you for your trust and wish you all the best with your new high-per-
formance MOBOTIX T26 DoorStation.
Cindy Jones
Thomas Jones
The Jones
Family
Dr. Jones, MD

9
More security thanks to
maximum overview
HD 360° Full Image: Entire scene in one view
HD Super 180° Panorama

10
T26 System Manual Part 1
What Are the Specic Advantages of A MOBOTIX DoorStation?
The new DoorStation from MOBOTIX oers an innovative, powerful solution that is easy
to install and takes a dierent approach to the solutions available on the market up to
now. The T26 is based on the international video telephony standard VoIP/SIP. All of the
modules oered for outdoor use are weatherproof, maintenance-free and can be used in
temperatures ranging from –30 to 50°C/–22 to 122°F. Here are the most important system
advantages at a glance:
Allround View Without Blind Spots
With6megapixelimagesensorand internalmemory,thishemisphericdoor camerarecords
the entire entrance area. No blind spots from wall to wall and from oor to ceiling.
Two-Way Video Communication Worldwide
When the doorbell rings, a connection is established with an IP video phone or a standard
computer via the network. For two-way video communication and for opening the door.
Recording With Sound
Thecamerain the door stationcanrecordevents automatically. Forexample,whensome-
one rings the doorbell or if something moves in front of the door.
Keyless Access
Who has access and who doesn’t? The door opener can be controlled tamper-proof using
the KeypadRFID with a PIN code or an RFID transponder.
Integrated Message Function
Digital voice messages for residents can be le directly at the door station and played
back aer authentication.
Very Simple Installation
Thedoor stationisconnectedto the networkviaanEthernetcableorviatwo-wirecabling
thanks to Mx2wire+ technology.
The T26 modules are avail-
able individually or in a set
MOBOTIX integrates hemispheric technology into exist-
ingsystemsof third-partymanufacturers,thusproviding
added security thanks to superior overview images and
event-controlled recording of video and sound.