Mocka Dahlia User manual

Dahlia Three Drawer
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
1
Wall Strap
x2
washer
Z
Y
wall
anchor
x1
X
safety
strap x1
WV
screw
x1
wall
screw
x1
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device
provided should fit most wall types, but please note that different wall materials may require different fixing
devices from those supplied.
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
bolt
x37
ABCDEF
G H J K I
Hardware Supplied
dowel
x10
small
screw x30
slide
rail x3
slide
rail x3
slide
rail x3
slide
rail x3
locking
nut x37
screw
x18
x8
wedge plastic
glide x4
Phillips & Flathead screwdrivers
and hammer required
L
screw
x8

Dahlia Three Drawer
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
2
1 2
E
E
E
Attach 3x slide rails (F) to panel [2] and secure with 9x small screws (E).
Tighten with a screwdriver. Insert 9x bolts (C) into panel [2]. Tighten
with a screwdriver.
Attach 3x slide rails (G) to panel [3] and secure with 9x small screws (E).
Tighten with a screwdriver. Insert 9x bolts (C) into panel [3]. Tighten with
a screwdriver.
.
F
F
F
G
G
G
C
C
C
C
C
C
3
2
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C
F
E
G
CR
CL
C
C
C
C
C
CC
CC
CC

Dahlia Three Drawer
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
3
34
Attach panels [4], [5], [6], [7] and [8] to panel [2] with 3x dowels (A)
and secure with 9x locking nuts (D). Tighten with a screwdriver.
Slide panel [9] down along the grooves between the panels [7] and [8] as shown.
4
5
6
7
7
8
8
9
5
2
A
A
A
D
D
D
D
D
DD
DD
D
D

Dahlia Three Drawer
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
4
65
Attach panel [3] to panels [4], [5], [6], [7],and [8] with 3x dowels (A)
and secure with 9x locking nuts (D). Tighten with a screwdriver.
Attach 4x plastic glides (K) to the panels [2] and [3] using a hammer
as shown.
Slide panel [9] down along the grooves between the panels [2] and [3] as shown.
4
5
5
6
7
8
3
2
9
2
D
D
D
D
D
D
K
D
3
A
A
A
K
K
K
K

13
2
1
Dahlia Three Drawer
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
5
78
Insert 4x bolts (C) to panel [1]. Tighten with a screwdriver. Attach panel [1] to the unit with 4x dowels (A) and secure with 4x locking
nuts (D). Tighten with a screwdriver.Attach panel [1] to panel [4] and
secure with 3x screws (B). Tighten with a screwdriver.
C
C
C
C
A
A
B
B
B
D
D
D4
B

Dahlia Three Drawer
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
6
9 Drawer x3 10 Drawer x3
Insert 5x bolts (C) to panel [10]. Tighten with a screwdriver. Attach panel [11], [12] and [13] to panel [10] and secure with 5x locking nuts (D).
Tighten with a screwdriver.
C
C
C
C
C
10
10
11
13 12
D
D
D
D
D

Dahlia Three Drawer
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
7
11 Drawer x3
Assembly Instructions
Slide panel [14] along the grooves between the panels [11] and [12] . Attach panels [11], [12] and [15] as shown using 5x screws (B).
Tighten with a screwdriver.
12 Drawer x3
14 12
12
11
11
15
B
B
B
B
B

13 Drawer x3
Dahlia Three Drawer
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
8
14
Attach slide rail (I) and slide rail (H) to the underside of the side panels
as shown. Secure with 4x small screws (E) and tighten with a screwdriver.
Insert the assembled drawers into the corresponding compartments
as shown. Ensure the drawers slide easily along the rails.
I
H
E
E
E
E
12
11

Dahlia Three Drawer
Assembly Instructions
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
9
15 16
Attach 8x wedges (J) into the corners of the back of the unit and
secure with 8x screws (L). Tighten with a screwdriver. Attach 1x
safety straps (V) to the top of the back side of the unit as shown
using 1x washers (Z) and 1x screws (W). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to
create a small hole lining up with the top of the safety strap (V).
Fasten to the wall using 1x washer (Z) , 1x wall anchor (X) and
1x wall screw (Y). Ensure unit is balanced and steady before
use. You're done, enjoy!
L
J
J
L
V
V
Z
W
Z
W
X
Y
Z
wall
anchor
screw
strap
washer