Mocka Kennedy User manual

Phillips & Flathead screwdrivers required
*We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.
Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%.
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing
device provided should fit most wall types, but please note that different wall materials may require
different fixing devices from those supplied.
Wall Strap
x2
washer
Z
Y
wall
anchor
x1
X
safety
strap x1
WV
screw
x1
wall
screw
x1
A B C D E F G HJKL
M N
I
O
Hardware Supplied
PQR
dowel
x20
screw
x41
bolt
x24
locking
nut x24
bolt
x4
screw
x5
slide
rail x1
wedge
x12
slide
rail x1
slide
rail x1
slide
rail x1
allen
key x1
bracket
x3
cover
x3
stopper
x3
hinge
x4
small
bolt x16
bracket
x4
ST
screw screw
x10 x12
U
adjuster
x1
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
A1
washer
x16
Kennedy Entertainment Unit
1
mocka.co.nz | mocka.com.au
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.

12
19
Attach 2x brackets (M) to panel [1] and secure with 4x screws (E). Place 2x
covers (N) over them as shown. Attach panel [8] to panel [1] using 2x screws
(S). Attach 1x bracket (M) to panel [2] and secure with 2x screws (E). Place
1x cover (N) over the bracket. Attach the support leg [19] to the underside of
panel [2] with 1x screw (F). Tighten with a screwdriver.
Attach 1x slide rail (H) to panel [5] and secure with 2x screws (E).
Attach 1x slide rail (J) to panel [6] and secure with 2x screws (E).
Tighten with a screwdriver.
8
2
1
EE
E
SE
EE
M
M
M
N
M
E
6
5
H
E
E
J
EE
M
S
E
F
EE
H x1 & J x1
Kennedy Entertainment Unit
2
mocka.co.nz | mocka.com.au
Assembly Instructions

34
Attach panels [5] and [6] to panel [7] using 4x dowels (A) and 4x bolts
(B). Secure with 4x locking nuts (C) and tighten with a screwdriver.
Attach panels [4], [6], [5] and [3] to panel [1] using 8x dowels (A), 8x bolts
(B) and secure with 8x locking nuts (C). Tighten with a screwdriver.
C
6
7
5
4
3
C
C
CA
B
A
B
A
B1
C
C
C
C
A
BA
B
A
BAB
A
BAB
A
BAB
C
6
5
Kennedy Entertainment Unit
3
mocka.co.nz | mocka.com.au
Assembly Instructions

56
Slide panels [9] and [10] along the grooves between panels [3], [4], [5]
and [6] to form the back of the unit.
Attach panel [2] to the rest of the unit using 8x dowels (A), 8x bolts (B)
and 8x locking nuts (C). Tighten with a screwdriver.
10
9
9
2
A
B
C
C
CC
C
C
C
AB
BB
BB
AA
AA
A
B
AB
4
3
5
6
Kennedy Entertainment Unit
Assembly Instructions
4
mocka.co.nz | mocka.com.au

Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
mocka.co.nz | mocka.com.au
78
Attach a leg bracket (R) to each leg [18] using 2x screws (S) and 1x bolt
(G). Tighten with a screwdriver and allen key (L). Attach each leg [18] to
panel [2] using 4x small bolts (Q) and 4x washers (A1) as shown. Tighten
with the allen key (L). Insert the adjuster (U) into the middle support.
Attach 12x wedges (D) to the back of the unit as shown and secure with
12x screws (T). Tighten with a screwdriver.
D
T
2
18
R
Q
Q
Q
U
L
G
LS
S
X4
19
A1
A1
A1
A1
Q
18
Front
Back
Front
Kennedy Entertainment Unit
Assembly Instructions
5
mocka.co.nz | mocka.com.au

910
Attach 1x stopper (O) to door panel [11] using 1x screw (E). Attach 2x
hinges (P) to panel [11] and secure with 4x screws (E). Attach 1x
stopper (O) to door panel [12] using 1x screw (E). Attach 2x hinges (P)
to panel [12] and secure with 4x screws (E). Tighten with a screwdriver.
Secure door panels [11] and [12] to the main unit by attaching the other end
of the hinges (P) with 16x screws (E) as shown. Tighten with a screwdriver.
12
11
E
O
E
O
P
P
EE
E
E
NOTE: If the doors are uneven or
there is a gap in the middle, loosen
or tighten the screw on the door
hinge until they are sitting flush.
12
11
x4
P
E
Kennedy Entertainment Unit
Assembly Instructions
6
mocka.co.nz | mocka.com.au

11
12
Insert 4x bolts (B) into panel [13].Attach 1x plug (O) to panel
[13] and secure with 1x screw (E).Tighten with a screwdriver.
Drawer x1
Kennedy Entertainment Unit
Assembly Instructions
7
mocka.co.nz | mocka.com.au
B
B
B
B
C
C
14
15
C
C
E
O
13
13
Drawer x1
Attach panel [14] and [15] to front panel [13] using 4x locking nuts (C).
Tighten with a screwdriver.

13
14
Slide panel [17] along the grooves between the side panels [14] and
[15] to form the base of the drawer.
Attach panels [14], [15] and [16] as shown using 4x screws (F).
Tighten with a screwdriver.
Drawer x1
Kennedy Entertainment Unit
Assembly Instructions
8
mocka.co.nz | mocka.com.au
14
15
17
14
15
17
FF
F
F
16
13
13
Drawer x1

15
16
Attach slide rails (K) and slide rails (I) to the underside of the side panels
as shown.Secure with 4x screws (E) and tighten with a screwdriver.
Drawer x1
Kennedy Entertainment Unit
Assembly Instructions
9
mocka.co.nz | mocka.com.au
14
Insert the drawer into the unit at an upwards 45˚angle. See the diagram
above for the correct positioning of the slide rails.
Ensure the drawer slides easily along the rails.
E
E
E
E
I
K
14
17
13
angle. See the diagram˚
above for the correct positioning of the slide rails.
Insert the drawer into the unit at an upwards 45
45°

17 18
Attach 1x safety strap (V) to the top of the back side of the unit as shown
using 1x washer (Z) and 1x screw (W). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (V). Fasten to wall
using 1x wall plug (X), 1x washer (Z) and 1x wall screw (Y). Ensure unit
is balanced and steady before use. You’re done, enjoy!
Wall Mount
wall
plug
wall
screw
strap
washer
X
Y
Z
V
Z
V
W
V
W
Z
Kennedy Entertainment Unit
Assembly Instructions
10
mocka.co.nz | mocka.com.au