Modular Closets Cubby Tower 18" Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
CUBBY TOWER
18" / 24" / 30"
1-844-969-4247
suppor[email protected]

ASSEMBLY AND INSTALLATION INSTRUCTIONS
CUBBY TOWER - 18" / 24" / 30"
PARTS LIST
KLM
N
1
A
B
C
D
E
Left Side Panel (Qty 1)
Right Side Panel (Qty 1)
Adjustable Shelf (Qty 2)
Set Shelf (Qty 2)
Rear Hanging Cleat (Qty 3)
F
G
H
I
J
Floor Support Panel (Qty 2)
Cam Post (Qty 18)
Camlock (Qty 19)
Shelf Pins (Qty 8)
Wood Dowels (Qty 4)
K
L
M
N
O
Level
Stud Finder
Drill, 3/32" bit size
Phillips Screwdriver
Screws, 3"
TOOLS REQUIRED
(not included)
1.1
1.2
Lay parts out on a protective surface to prevent damage. Tip: Spread out the cardboard packaging to
use as a protective surface.
Inventory parts against the Parts List. Make sure all parts are present before proceeding.
G
IH
O
AB C
D
E
FINISHED EDGE
FINISHED EDGE
FINISHED EDGE
FRONT
FRONT
F
FRONT
J

ASSEMBLY AND INSTALLATION INSTRUCTIONS
CUBBY TOWER - 18" / 24" / 30"
2
3
2.1 Install one Cam Post (F) into each of the eight holes on Left Side Panel (A) and Right Side Panel (B). Tighten until
Cam Posts are seated against Side Panels.
B
A
G
G
G
G
3.1 Assemble Set Shelves (D) and Rear
Hanging Cleats (E) onto Right Side Panel
(B) by sliding the Shelves and Cleats onto
the Cam Posts (F) on Side Panel. BE SURE
dowel pins in Shelves and Cleats engage
drilled holes in Side Panel, and all parts are
pressed flush against Side Panel.
IMPORTANT NOTES
Install Set Shelves (D) with finished edges facing
forward (toward front of unit).
Install Rear Hanging Cleats (E) with holes for
Cam Locks facing the rear of the unit and the
unfinished edge against the Set Shelf (D).
If the Tower will be installed with upper Set Shelf
(D) above eye level, install upper Set Shelf (D)
with holes for Cam Locks facing the top of the
unit. If the Tower will be installed with upper Set
Shelf (D) below eye level, install upper Set Shelf
(D) with holes for Cam Locks facing the bottom
of the unit.
Install lower Set Shelf(D) with holes for Cam
Locks facing the bottom of the unit.
D
B
E
D
E
G
G
NOTE: There are drilled holes in the bottom edge of Side Panels for installation
of Floor Support Panels. BOTTOM

ASSEMBLY AND INSTALLATION INSTRUCTIONS
CUBBY TOWER - 18" / 24" / 30"
4
5
E
D
E
D
B
A
4.1 Install Left Side Panel (A) onto assembled
Set Shelves (D) and Rear Hanging Cleats
(E). BE SURE dowel pins in Shelves and
Cleats engage drilled holes in Side Panel,
and Side Panel is pressed flush against Set
Shelves and Cleats.
D
D
E
E
H
H
H
H
ARROW TOWARD
CAM POST OPENING
5.1
5.2
Insert Camlocks (H) in holes in Set
Shelves (D) and Rear Hanging Cleats
(E), with arrow pointing toward Cam
Post opening. Be sure Camlocks engage
Cam Posts, and are fully seated in Shelves
and Cleats.
Tighten Camlocks (H) clockwise to lock.

ASSEMBLY AND INSTALLATION INSTRUCTIONS
CUBBY TOWER - 18" / 24" / 30"
6
FOR FLOOR MOUNT INSTALLATIONS ONLY
6.1
6.2
6.3
6.4
6.5
Install one Cam Post (G) into each of two Floor Support
Panels (F). Tighten until Cam Posts are seated
against Panels.
Assemble Floor Support Panels (F) onto Rear Hanging
Cleat (E) by sliding the Cam Posts (G) into Cleat. BE SURE
dowel pins in Cleat engage drilled holes in Floor Support
Panels, and all parts are pressed flush against each other.
Insert Camlocks (H) in holes in Rear Hanging Cleat (E),
with arrow pointing toward Cam Post opening. Be sure
Camlocks engage Cam Posts, and are fully seated in Cleat.
Tighten Camlocks (H) clockwise to lock.
Insert four Wood Dowels (J) into holes in edges of Floor
Support Panels (F).
Align Wood Dowels (J) in assembled Floor Support with
holes in Cubby Tower and press Tower and Floor Support
together.
G
F
F
E
J
J
H
ARROW TOWARD
CAM POST OPENING

ASSEMBLY AND INSTALLATION INSTRUCTIONS
CUBBY TOWER - 18" / 24" / 30"
7
INSTALLATION
7.1
7.2
7.3
Determine the mounting location for the unit. The unit can be wall mounted or floor mounted (by installing the Floor
Support Panels as shown in step 6).
Using a stud finder, locate studs to which the unit will be secured. Mark stud locations with a pencil.
With the unit positioned at the desired location, level the unit, then drill pilot holes through Rear Hanging Cleats (E),
NOTE: For 18" and 24" units, it is likely that only one stud will pass through the unit. In these cases, use two screws
through each Rear Hanging Cleat.
12" FROM
FLOOR STUDSSTUDS
E
E
PILOT
HOLES
PILOT
HOLES
FLOOR MOUNT WALL MOUNT

8.1 Secure Rear Hanging Cleats (E) to studs
using 3" Screws (O).
ASSEMBLY AND INSTALLATION INSTRUCTIONS
CUBBY TOWER - 18" / 24" / 30"
8
9
C
9.1
9.2
For each Adjustable Shelf (C), insert
four Shelf Pins (I) into pin holes inside
the Tower at the desired height.
Rest Adjustable Shelves (C) on Shelf
Pins (I).
E
M
I
II
I