Modular Closets MUDROOM Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
MUDROOM
suppor[email protected]
1-844-969-4247

ASSEMBLY AND
INSTALLATION INSTRUCTIONS
MUDROOM
FRONT
FRONT FRONT
FRONT
AB
EF
GH
CDi
FINISHED EDGE
FINISHED EDGE
FINISHED EDGE
FINISHED EDGE FINISHED EDGE
PARTS LIST
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Left Side Panel, Upper (Qty 1)
Right Side Panel, Upper (Qty 1)
Set Shelf, Upper (Qty 2)
Adjustable Shelf, Upper (Qty 1)
Left Side Panel, Bench (Qty 1)
Right Side Panel, Bench (Qty 1)
Top Shelf, Bench (Qty 1)
Set Shelf, Bench (Qty 1)
Cleat (Qty 5)
Cam Post (Qty 30)
Camlock (Qty 30)
Shelf Pins (Qty 4)
Wood Dowel, 8mm (Qty 8)
Screw, 2.5" (Qty 2)
Hook, 3-Prong (Qty 2)
Hook, 2-Prong (Qty 1)
Screw, 0.75" (Qty 6)
L
JK
M
O
P
N
Q
1A

R
S
T
U
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
MUDROOM
1B
V
W
X
Y
ZAABB
CC DD
PARTS LIST
R
S
T
U
V
W
X
Y
Z
AA
BB
CC
DD
Drawer Panel, Front (Qty 1)
Drawer Panel, Rear Qty (1)
Drawer Panel, Side (Qty 2)
Drawer Front (Qty 1)
Drawer Bottom (Qty 1)
Drawer Slide (Qty 2)
Shelf Slide (Qty 2)
Drawer Handle (Qty 1)
Euro Screw, 5/8" (Qty 2)
Screw, 5/8" (Qty 2)
Screw, 1" (Qty 18)
Screw, 1.5" (Qty 6)
Wood Dowel, 6mm (Qty 24)
1C
1.1
1.2
Lay parts out on a protective surface to prevent
damage. Tip: Spread out the cardboard packaging
to use as a protective surface.
Inventory parts against the Parts List. Make sure
all parts are present before proceeding.
Level
Stud Finder
Drill, 5/32" bit size
Phillips Screwdriver
TOOLS REQUIRED
(not included unless noted)

ASSEMBLY AND
INSTALLATION INSTRUCTIONS
MUDROOM
TOP
2
3
2.1 Install one Cam Post (J) into each of the 6 holes on Bench Top Shelf (G). Tighten until Cam Posts are seated
against Top Shelf.
3.1 Install one Cam Post (J) into each of the 10 holes on Bench Left Side Panel (E) and Bench Right Side Panel (F).
Tighten until Cam Posts are seated against Side Panels.
G
E
F
J
J
J
J
JJJJ
JJ
JJJ
J
J
J
TOP

ASSEMBLY AND
INSTALLATION INSTRUCTIONS
MUDROOM
4
5
TOP
TOP
IMPORTANT NOTES
Install Bench Set Shelf (H) with finished edge facing forward
(toward front of unit) and holes for Cam Locks facing down (toward
the bottom of the unit).
Install lower Cleat (I) with holes for Cam Locks facing the rear of
the unit and the unfinished edge against Set Shelf (H).
Install upper Cleat (H) with holes for Cam Locks facing the rear of
the unit and the unfinished edge facing the top of the unit.
4.1 Assemble Bench Set Shelf (H), and two Cleats (I) onto Bench
Right Side Panel (F) by sliding the Shelf and Cleats onto Cam
Posts (J) on Right Side Panel. BE SURE dowel pins in Shelf
and Cleats engage drilled holes in Right Side Panel, and all
parts are pressed flush against Panel.
H
F
E
H
J
JJ
J
J
I
I
I
I
5.1 Install Bench Left Side Panel (E) onto assembled Set Shelf
(H) and Cleats (I). BE SURE dowel pins in Shelf and Cleats
engage drilled holes in Side Panel, and Side Panel is pressed
flush against Set Shelf and Cleats.