Modular Closets Vista Short Tower Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
SHORT TOWER
1-844-969-4247 suppor[email protected]

PARTS LIST
A
BLeft Side Panel (Qty 1) Right Side Panel (Qty 1)
J
A B
C
EFINISHED EDGE
FINISHED EDGE
FRONT FRONT
D
C
FINISHED EDGE
FINISHED EDGE
F G
FRONT FRONT
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
SHORT TOWER
BOX 1 BOX 2
H
I
L
C
D
H
I
L
Rear Hanging Cleat (Qty 2)
Set Shelf (Qty 2)
Cam Post (Qty 12)
Camlock (Qty 12)
Screw, Square Drive, 2.5" (Qty 4)
BOX 4 Leg Extension Kit (Optional)
BOX 3
E
JAdjustable Shelf (Qty 2) Shelf Pins (Qty 8)
C
F
G
H
I
K
Rear Hanging Cleat (Qty 1)
Left Leg Extension (Qty 1)
Right Leg Extension (Qty 1)
Cam Post (Qty 2)
Camlock (Qty 2)
Wood Dowels (Qty 4)
Level
Stud Finder
Drill, 3/32" bit size
Phillips Screwdriver
Drill Bit, Square,
#2
TOOLS REQUIRED
(not included unless noted)
HK I
1A

2
2.1 Install one Cam Post (H) into each of the sic holes on Left Side Panel (A) and Right Side Panel (B). Tighten until
Cam Posts are seated against Side Panels.
BH
H
H
A
NOTE: There are drilled holes in the bottom edge of Side Panels for installation
of Floor Support Panels. BOTTOM
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
CUBBY TOWER
TOP
1.1
1.2
Lay parts out on a protective surface to prevent damage. Tip: Spread out the cardboard packaging to
use as a protective surface.
Inventory parts against the Parts List. Make sure all parts are present before proceeding.
1B

3
4
C
C
B
D
D
A
4.1 Install Left Side Panel (A) onto assembled
Set Shelves (D) and Rear Hanging Cleats
(C). BE SURE dowel pins in Shelves and
Cleats engage drilled holes in Side Panel,
and Side Panel is pressed flush against Set
Shelves and Cleats.
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
CUBBY TOWER
3.1 Assemble Set Shelves (D) and Rear
Hanging Cleats (C) onto Right Side Panel
(B) by sliding the Shelves and Cleats onto
the Cam Posts (H) on Side Panel. BE SURE
dowel pins in Shelves and Cleats engage
drilled holes in Side Panel, and all parts are
pressed flush against Side Panel.
IMPORTANT NOTES
Install Set Shelves (D) with finished edges facing
forward (toward front of unit).
Install Rear Hanging Cleats (C) with holes for
Cam Locks facing the rear of the unit and the
unfinished edge against the Set Shelf (D).
Install lower Set Shelf(D) with holes for Cam
Locks facing the bottom of the unit.
B
C
C
D
D
H
H
TOP
TOP

5
6
D
D
C
C
H
H
K
K
F
G
C
HI
H
H
H
H
ARROW TOWARD
CAM POST OPENING
5.1
5.2
Insert Camlocks (H) in holes in Set
Shelves (D) and Rear Hanging Cleats
(E), with arrow pointing toward Cam
Post opening. Be sure Camlocks engage
Cam Posts, and are fully seated in Shelves
and Cleats.
Tighten Camlocks (H) clockwise to lock.
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
CUBBY TOWER
FOR LEG EXTENSION KIT INSTALLATIONS ONLY
Leg Extension Kit purchased separately)
6.1
6.2
6.3
6.4
6.5
Insert four Wood Dowels (K) into holes in edges of Left Leg
Extension (F) and Right Leg Extension (G).
Install one Cam Post (H) each into Left Leg Extension (F)
and Right Leg Extension (G). Tighten until Cam Posts are
seated against Leg Extensions.
Assemble Left Leg Extension (F) and Right Leg Extension
(G) onto Rear Hanging Cleat (C) by sliding the Cam Posts (H)
into Cleat. BE SURE Wood Dowels (K) in Cleat engage drilled
holes in Leg Extensions, and all parts are pressed flush against
each other.
Insert Camlocks (I) in holes in Rear Hanging Cleat (C),
with arrow pointing toward Cam Post opening. BE SURE
Camlocks engage Cam Posts, and are fully seated in Cleat.
Tighten Camlocks (I) clockwise to lock.
Align Wood Dowels (K) in assembled Leg Extensions with
holes in Shelf Tower, and press Tower and Leg Extensions
together.

7
INSTALLATION
7.1
7.2
7.3
Determine the mounting location for the unit. The unit can be wall mounted or floor mounted (by installing the Floor
Support Panels as shown in step 6).
Using a stud finder, locate studs to which the unit will be secured. Mark stud locations with a pencil.
With the unit positioned at the desired location, level the unit, then drill pilot holes through Rear Hanging Cleats (C),
NOTE: For 18" and 24" units, it is likely that only one stud will pass through the unit. In these cases, use two screws (L)
through each Rear Hanging Cleat.
12" FROM
FLOOR STUDSSTUDS
C
C
WITH LEG
EXTENSION KIT WITHOUT LEG EXTENSION KIT
ASSEMBLY AND
INSTALLATION INSTRUCTIONS
CUBBY TOWER
PILOT
HOLES
C
C
PILOT
HOLES

ASSEMBLY AND
INSTALLATION INSTRUCTIONS
CUBBY TOWER
8
9
8.1 Secure Rear Hanging Cleat (C) to studs
using 2.5" screws (L).
9.1
9.2
For each Adjustable Shelf (E), insert
four Shelf Pins (J) into pin holes inside
the Tower at the desired height.
Rest Adjustable Shelves (E) on Shelf
Pins (J).
C
L
E
JJJ
J